Question about Chrysler Cars & Trucks
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: 1997 sonoma turn signal flasher
it is inside, under dash, on left side is a plastic sound protector, mine had 3 screws holding it up, drop this down and straight in you will see a 1" round thing - this is the flasher, pull it out and replace with new one (there are two flat prongs that plug in). It appears this is a well guarded secret!
Posted on Aug 26, 2008
SOURCE: 1994 devilles flasher location
Turn signal flasher module is behind dash left of steering column near chime module. I have a 94 Seville and I had that same problem you need a Turn Signal Flasher Moduel, I forgot the proper term for it but I had to get mine replaced too. When I hit the signals to turn the side light would come on but the signal light wouldn't. Its a little box you get from Cadillac it only cost like $20 - $25 and you get it installed and trust. It'll work again. I just got mine done this week and my car now has turn signals again.
Posted on Dec 15, 2008
Unsure what engine or Vin Number is for your Car. All 0f the diagrams looked the same for the 2.2 - 2.5 and others, with and with out turbo.
Hope this helps, - Jarett
Posted on Aug 17, 2009
On the 1993 Sedan de Ville, The hazard flasher is easy to locate, under the dash between the steering column and the radio. Looking up, you will see the smooth round side of the flasher and the wires will be attached to the top.
The turn signal flasher is more difficult to get to, but readily accessed with a T-15 torx driver and a little patience. It is located to the left of the steering column, but is most easily accessed through the dash panel instead of from underneath.
1. remove the T-15 screw from above the headlight switch, above the fuel data center, and above the small panel similar to the one around headlight switch. All of these are somewhat hidden, and you'll need to feel for them or get low and look up at them.
2. Using a bent piece of wire or an allen wrench, or anything else handy, pull off the small trim piece that is directly below the steering column. On my car, this is wood-grained plastic. This will expose two more screws that need to be removed.
3. Now, you should be able to remove the large dash trim panel that goes around the fuel data center.
4. Unscrew the two T-15 screws that hold the fuel data center into the dash, and it should pull straight forward. There should be plenty of wire to move it out of the way.
5. The turn signal flasher is the silver can that you see to the right in the opening you just created by removing the fuel data center module. It has a single plug with two conductors on the back. I had to use a small screwdriver to pry it off.
It is a different part number, so I don't know if you can just swap it for the hazard flasher to test it like you can on many cars. I just replaced mine with a Wagner 323, which is what came out of mine.
Posted on Apr 30, 2010
Tips for a great answer:
Jan 27, 2013 | 1993 Plymouth Sundance
Jan 16, 2013 | 1994 Plymouth Sundance
Apr 26, 2012 | 1992 Plymouth Sundance
Jun 27, 2011 | 1989 Plymouth Acclaim
Mar 31, 2011 | 1991 Plymouth Sundance
Sep 07, 2010 | 1993 Plymouth Sundance
Jan 29, 2010 | 1990 Plymouth Sundance
Dec 13, 2009 | 1994 Plymouth Sundance
Jun 05, 2009 | 1992 Plymouth Sundance
80 people viewed this question
Usually answered in minutes!