Question about Honda Accord

Open Question

How to change fuel filler neck on 1989 honda accord

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

polarcycle
  • 1392 Answers

SOURCE: How to change dodge neon fuel filler neck

unbolt the neck from the body of the car. Drop the gas tank enough to get the neck out. Reinstall.

Posted on Mar 10, 2009

  • 5 Answers

SOURCE: Is a 2000 Dodge Grand Caravan fuel filler neck usable in a 1999?

yes it will swap and you have to remove it from the bottom of the van remove the screw/clips from inside the filler door and then from underneth disconect the filler tube ti tank and the vent hose to the tank i belive there is a bracket also holding the filler tube to the body with one bolt then it snakes out of the va r insalating is just reverse

Posted on Jun 25, 2009

scottyoung56
  • 89 Answers

SOURCE: gas cap is contacting inside of filler neck

YES IT CAN FROM THE RUBBER HOSE UP TO WHERE YOU PUT THE GAS IN

Posted on Aug 08, 2009

jim9813
  • 124 Answers

SOURCE: Replacing fuel filler neck on 2000 Crown Vic

Good news, no the tank doesn't have to come down. However, there needs to be less than 3/4 tank. Jack it up and set on a jack stand, remove the wheel, four screws housing to pipe, filler pipe sensing hose from filler pipe, screw retaining the cap, four retaining screws from filler pipe, screw from filler pipe retainer, slide into the tank until it can be rotated and pulled out through the fender. lube the tank grommet with clean oil and reverse the removal for install.

Posted on Aug 21, 2009

  • 169 Answers

SOURCE: gas leak on fuel filler neck

if it's a hose or pipe go to dealer or junk yard get another if broken clamp replace if neck part of tank call rad shop see if the can solder if you drain & pull tank

Posted on Aug 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car is a 2000 Honda accord, engine light came on checked gas cap,it was ok,shop checked it with machine and code P 1457 came up.What does it mean, & and how do i fix it?


P1457 90 EVAP Emission Control System Leak Detected (Control Canister System) Possible causes
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
It means that your fuel tank isn't airtight. It could be a crack in the filler pipe, a loose hose or even a blown gasket at the fuel gauge sender.
Your car does a vacuum check on the fuel system now and then. If it detects it's not air tight, it throws a code. Now, the gas capis the most common thing. But from the fuel filter to the filler neck something is not right. Look for a small gas leak, stick your head under the car and give it a whiff. see if you smell it, if you have a garage put sheets of news paper under your car over night and see if any leeks drip on it. There's other things but try those first.

May 31, 2014 | 2000 Honda Accord

1 Answer

P0442 CODE SMALL LEAK IN EVAP. CHANGED GAS CAP CODE CAME BACK CAP IS OEM PARTS


There could be a tiny rust hole in the fuel filler neck ,or the cap may not be sealing the filler neck properly. Check for rust on the filler neck, and on the sealing surface of the filler neck opening.

Sep 25, 2010 | 2003 Kia Spectra

1 Answer

My 1998 honda accord check engine light Is on. And there are two p codes 1259 and 1456. how to fix?


Fuel filler cap is loose. 1456

Tighten *at least SIX* clicks. Wait three engine on-off cycles. Light
should go off.

If it does not go off, the cap may not fit tightly enough for a proper
seal. Replace cap. Occasionally, the threads in the filler necks can be
damaged, preventing the cap from being properly tightened.

"P.O. 1259 - VTEC malfunction
http://www.honda-tech.com/showthread.php?t=871949
this should help

Aug 18, 2010 | 1998 Honda Accord

3 Answers

How do you put a fuel pump on?


I HAD A 92 HONDA AND ALL I DID WAS LOWER THE BACK SEAT AND LIFT THE RUG FROM THE TRUNK AND THERE IS A COVER WITH ABOUT 6 SCREWS THAT GIVE YOU ACCESS TO THE FUEL PUMP.I BELIEVE THIS HONDA SHOULD HAVE THE SAME ACCESS COVER.HOPE THIS INFO HELPS.TAKE CARE AND GOOD LUCK, MANNY

Feb 25, 2010 | 1994 Honda Accord

1 Answer

What is the best way to replace the fuel intake hose to the fuel tank on a 1989 ford ranger truck?im told by the state of calif. smog station that it releases fumes and will not pass the smog test.


If you are talking about the fuel filler neck or fuel filler hose, the easiest way is to remove the bed by removing the six bolts that attach it to the chassis. also disconnect the light harnesses and lift up your bed. don't forget to first release the fuel filler neck by removing three small screws at the gas filler port. then remove the hose from the tank. it is attached to the tank by a clamp. I just did two of them and it is fairly simple. It should take you about three hours if you have all the tools.

Oct 16, 2009 | 1989 Ford Ranger

1 Answer

Leaky filler tube 1992 Accord LX need replacement


The filler neck is much more than the rubber boot you speak of. Here's a link to one place it can be purchased on line. You can do a Google search for other sources.

http://www.ecrater.com/product.php?pid=3619135


1f2f801.jpg

Sep 22, 2009 | 1992 Honda Accord

1 Answer

INSTRUCTIONS TO INSTALL FUEL PUMP ON 1989 CORVETTE


REMOVAL
  1. Relieve fuel system pressure.
  2. Disconnect battery ground cable.
  3. Remove fuel filler door.
  4. Remove fuel cap.
  5. Remove fuel tank filler neck housing and disconnect drain hose.
  6. Remove screws attaching fuel meter/fuel pump to tank.
  7. Disconnect fuel lines, fuel vapor line and electrical connector.
  8. Remove fuel meter/fuel pump and gasket.
  9. Replace fuel pump.
INSTALLATION
  1. Reverse procedure to install.

Jul 27, 2009 | 1989 Chevrolet Corvette

2 Answers

Fuel pump


i have an 1989 accord ,and i changed the fuel pump.1. take out the back set.2,there will be an acess panel under the set, take the screws out then you have 8 nuts to remove the pump.

Aug 03, 2008 | 1989 Honda Accord 4 Door

1 Answer

Need pressure spec for fuel pump on carburated 89 accord


need to know how to change the fuel pump, do i have to drop the fuel tank or can i get to it from under the back seat

Jul 26, 2008 | 1989 Honda Accord 4 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...