Question about 1996 Ford Ranger SuperCab

Open Question

How do i remove c clips in 7.5 ford ranger axle rear seal out

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fyrebyrd1
  • 121 Answers

SOURCE: 98 Ford F-150 2WD rear axle removel

The Ford is similar to the Chevy. Same procedures apply. Same retaining bolt in center section needs to be removed to allow cross shaft to come out. Same technique in removing spider gears. Same "C-clip" retainers on axle ends. you shouldn't have any issues.

Posted on Nov 02, 2008

Ad
ourhowse
  • 2007 Answers

SOURCE: removal of axle 1997 ford explorer awd

You have to take the rear differential apart, and then pull the axle.

Posted on May 05, 2009

heavymetal77
  • 721 Answers

SOURCE: rear axle leaking

Block the front tires. Break the rear lugs loose. Jack up the rear of the truck at the center if possible. remove the wheels & brake drums. Remove the brake shoes,return springs & all the other hardware. Remove the differential cover & drain oil. If you have a posi the next step sucks. You need to remove the threaded pin from the housing & remove the axle retaining clips. All the while,being carefull of the spring in the posi unit. If no posi,then same procedure,minus the "pucker factor". After the axle is out,take a large flat blade screw driver or pry bar & pop the seal out. Keep in mind the axle bearing is probably gone too , so that's another procedure. Keep it apart,you'll be glad you did.

Posted on Jun 23, 2009

2coolrick
  • 560 Answers

SOURCE: How do you remove c-clips on axle of 95 ford rear

If you have already removed the outer axle bearing cover in the rear hub, try popping the axle out as some of them have a compression clip holding it in place in the differential. If it doesn't pop loose, you wil have to remove the differential cover and push the axle inward enough to access the retaining clip to remove it. It should slide out fairly easile once the axle is pushed in far enough to clear the retainer clip lock collar.

Posted on Aug 17, 2009

  • 1 Answer

SOURCE: want to replace rear axle seal on 2000 ford

i have problem with my car ford expedetion air suespention syestem some time it is not work

Posted on Sep 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear axel seal replacement 1988 Ford F150


Pull rear differential cover, remove small bolt/pin that holds pin in, remove pin, push axles in and remove both c clips, pull axles out and then remove seals....reverse procedure but ensure to fill diff with gear oil until it comes out the fill hole.

Feb 17, 2015 | Ford Cars & Trucks

1 Answer

How do you remove rear axle from 1995 ford ranger 2 wheel drive need to replace oil seal


Raise the vehicle and properly support it. Remove the wheel and drum. Remove the rear diff cover, have a drain pan underneath to catch the gear oil. Place the trans in nuetral, chalk the front wheels to keep vehicle from moving if you forget to put it back into park befor you lower the vehicle. Rotat the differential until you see the bolt that holds the diff pin in place. Remove the bolt, 5/16 or 8 mm I believe. You can then remove the diff pin, do not rotate the diff with the diff pin removed! Push the axle in, you can then remove the C-clip that holds the axle to the side gear, it will usuall drop or just fall out. Pull the axle out of the rear diff and replace the seal. Put everything back together. Use black or grey RTV to reseal the diff cover making sure o clean up both surfaces as best you can. Put trans in park. Lower the vehicle. Remove the fill plug from the side of the differential and fill with gear lube until lube comes out the hole. Reinstall the plug and your good to go. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Mar 15, 2012 | 1995 Ford Ranger Supercab

1 Answer

The right rear axle is bent on my 2005 Ranger. How do I remove and replace this axle? Does it have a clip that locks it into the differential?


kiker graham, Yes there is a clip that holds the axle in the differential. First jack up the back of the vehicle and support with jack stands. Put the transmission in neutral. Remove the wheel and brake drum from the axle you want to remove. Place a catch basin under the differential and remove all the bolts on the rear cover of the differential. Remove the cover and let the gear oil drain out. You may have to move the break line to remove the cover. When the oil has drained out turn the drive shaft until you see a small bolt in a recess on the right side of the assembly on the opposite side on the main drive gear. This is an 8MM bolt that has to loosened very carefully. First, using a punch, place the punch on the head of the bolt and hit it a few times with a hammer to "loosen" it up. This is done to avoid breaking the bolt. If this bolt is broken then you are going nowhere with this job. BE VERY CAREFUL when removing this bolt. When the bolt is out you can move the pin that it is holding. You will notice that this pin is very close to the ends of the axles. Do not completely remove this pin as the side gears will fall out. Pull the pin out only as far as you need to, to push the axle in towards the center of the vehicle. There is a C clip that will fall out when you have done this. Sometimes you have to spin the C clip to get it to fall out. Pull the axle out only far enough to put the center pin back in place. After you do this push the center pin back in and put the small bolt back in to hold it in place. Remove the axle. If the axle is bent and you say it is then it would be a good idea to replace the axle seal at this time. You can use the axle itself to remove the seal. Use the groove where the C clip sits. Place on the inside of the seal. Using the axle as a pry bry, remove the seal. Replace the seal and put the new axle in. You will have to move the axle around a little to get it to engage the splines on the inside of the side gear. Once again pull the center pin out only far enough to push the axle all the way in. Place the C clip in the slot at the end of the axle and pull the axle out as far as you can. This wont be much. Push the center pin back in and replace the little lock bolt and tighten it up. Clean the cover and the back of the differential and use silicone to seal it. There is a fill hole on the front side of the differential. The plug for this hole will accommodate a three eigths ratchet. Fill the differential until the gear oil starts to spill out of the hole. Replace brake drum and wheel. Good luck with this.

May 13, 2011 | 2005 Ford Ranger

1 Answer

How do you remove an axle on the right rear of a 1999 explorer? it has a leaking wheel seal.


1. Drain diff if it has a plug.
2. Remove rear cover
3. Undo cross pin bolt and slide the cross pin out of the carrier
4. Push axle shaft in so you can remove the C clip
axle retainers
5. Slide axle out of housing.
6. Remove axle seal and then replace axle seal
7. Reverse steps

May 25, 2010 | 1999 Ford Explorer

1 Answer

Change rear whell seal 1997 f-150 gear oil comeing out of rear whell took tire off; took drum off; and saw gear oil all over brake shoes. Seal or bearing need to be replace? how?


replace the axle seal to replace pull the rear cover draining the gear oil then rotate the carrier around till the small bolt holding the carrier pin remove bolt pull pin out don"t turn carrier after pulling the pin push the axle in and remove the clip from the inside of the carrier that pin holds the axle clips in place after pulling out you can remove the axle then just pop the seal out and install new one use a socket or something that is the same size as the seal lube the axle and slide axle back in lift up when almost all the way in the tube putting it in the carrier once in replace clip and pullout on the axle thats it pretty much hope this helps you out

Mar 24, 2010 | 1991 Ford F250

1 Answer

Rear axle seal is leaking on 04 heritage model,does this rear end have same c-clip to remove axle as older models?


Should be same, just don't forget differential bolt and pin removal first to allow you to push axle in to remove "C" clip.

Oct 25, 2009 | 2004 Ford F150

2 Answers

How do i remove c clips in 7.5 ford ranger rear axle


Best method is to buy a pair of c-clip pliers which are designed for that purpose. Maybe Pep Boys or similar?

Charlie

Oct 03, 2009 | 1996 Ford Ranger SuperCab

2 Answers

Rear wheel seal leaking


Remember SAFETY FIRST. Jack up the right rear wheel, support the axle with a jack stand, remove the wheel, the brake drum, the banjo cover or differential cover. Allow the gear oil to drain out into you drain pan, carefully and slowly spin the ring gear (watch out not to pinch your fingers) look for a small bolt that is restraining the king pin, remove the bolt and then carefully slide the pin out !(don't spin the axles or ring gear while the pin is out) if you do the bushings and spider gers will move out of their places. After the pin is out then go over to the exposed axle and push it in until it stops. Go back over to the pumpkin and look inside, for a "U" shaped washer it will be on the end of the axle. Remove it from the axle. Now you can remove the axle and replace the wheel seal. Either rent a seal installing tool or carefully use a block of wood and evenly install the seal. If you kink or damage the new seal remove it and try it again. When you put everything back together put a little thread lock on the bolt for the king pin. dont over tighten it, could snap it. Let me know if I can help any more.

May 27, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Rear axle seal replacement 1994 ford bronco


It is fairly easy to do. remove rear wheels and brake drums, remove the differential cover, rotate the diff to access the diff pin bolt and remove, remove pin, push axles inward and remove c clips, slide out axles and replace seals. reverse procedure

Dec 29, 2008 | 1994 Ford Bronco

1 Answer

Rear Axle Removal


if you are talking about the axle seals, 1.REMOVE THE WHEELS.2. REMOVE THE DIFF COVER(slowly)3.REMOVE THE BRAKE CALIPER ASSEMBLY.4.REMOVE THE 8MM PIN IN THE DIFF CARRIER. 5.TURN CARRIER AND REMOVE THE LARGE PIN.6. FIRMLY HIT IN THE AXLE, A SMALL RETAINING C CLIP WILL FALL INTO THE DIFF HOUSING. DO THE SAME WITH THE OTHER SIDE. ( be careful if you have rear speed sensors remove it when you remove the brake calipers . you will break it when you are pushing in the axles.)7.pull axles and replace seals

May 29, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1996 Ford Ranger SuperCab Logo

Related Topics:

276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...