Question about GMC Sierra 1500

Open Question

2008 gmc sierra 1500 spindle nut torque specifications

Torque specs for a 2008 gmc sierra 1500 z71 4x4 spindle nut

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

Ad
  • 15 Answers

SOURCE: what are the front axle nut torque specs for a

185 ft.lbs

Posted on Oct 10, 2009

  • 14036 Answers

SOURCE: Just replaced front wheel bearing hubs assy. What

THE HUB AND BEARING ASSEMBLY MOUNTAINING BOLTS TORQUE IS 133 FT LBS.

Posted on Nov 14, 2009

c17hydro
  • 2984 Answers

SOURCE: is there a torque spec on the spindle nut for the

  1. nstall the caliper mounting bolts. Perform the following procedure before installing the caliper guide pin bolts (15 Series only).
  2. Remove all traces of the original adhesive patch.
  • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
  • Apply Red Loctite#272 to the threads of the bolt.
  1. Install the caliper mounting bolts (25 series). Tighten the caliper guide pin bolts to 42 Nm (31 ft. lbs.) on the 15 series; 108 Nm (80 ft. lbs.) on the 25 series.

Posted on Nov 19, 2009

Testimonial: "thank you that was very helpful"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 GMC Seirra Truck 4wheel drive 5.3L. Torque specs for lug nuts?


2001 GMC Truck Sierra 1500 4WD 5.3L SFI 8cyl

The Lug Nut Tightening Torque 140 Foot pounds (Final torque).

Oct 06, 2015 | GMC Cars & Trucks

2 Answers

How many ft/lbs of torque is recommended on the flywheel bolts when installing the flywheel on a 1996 GMC Sierra Z-71 4x4 5.7L engine?


GMC Sierra Bolt Torque Specifications. ... The torque converter bolts to the flywheel with 46 foot-lbs. of torque. ... 1996 GMC Sierra Horsepower Torque Specs.

May 02, 2014 | Cars & Trucks

1 Answer

How to assemble a front wheel bearing on a 2003 GMC Sierra 1500 4x4


The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

Oct 08, 2011 | Cars & Trucks

1 Answer

Yes what is the torque spec for the nut on the rear diff yoke?


Hi, there is no real torque spec., as the pinion gets tightened against a crush collar, creating a preload for the pinion, as the preload is tightened to 20-25 lbin, on a rotational measurement, the nut torques itself. This measurement can only be measured with the ring gear, and center section out of the housing. This may sound confusing, but this is how a typical setup would work. If you are replacing the seal, because of a leak, you could remove the flange, replace the seal reinstall the flange, snug it up, untill it is seated, then give it a small amount of tightening. You should not over tighten this nut, as it could result in pinion bearing damage. If you use caution, you can do this without an issue, Good luck...Coop

Sep 26, 2010 | 2006 GMC Sierra 1500 2WD

1 Answer

Torque specs for front spindle (nut hold brake drum in place)


Tighten till the wheel bearing is tight. No one really uses a specification for that, do it by feel. when the nut is tight, and there is no play in the bearing. Should be about 15-20 ft/lbs, with about .001-.003 end play if you need exact numbers though.

May 29, 2009 | 1965 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

850 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...