Question about Nissan Pickup

Open Question

How to replace a clutch in a 95 nissan pickup 4x4

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
carsandcomps
  • 722 Answers

SOURCE: i have a 95 nissan pickup it runs fine but has no

mfoster93,

Answer these questions to determine power loss while driving:

1. Do you hear any pinging or knocking? A bent rod will cause loss of power. ( should be able to hear wihtout strain)

2. Have you changed the fuel filter/airl filter recently? A plugged (dirty) fuel filter will cause this, as well as a plugged (dirty) air filter. Change both if needed.

3. Injected? On a full tank run one can of SeaFoam in the tank - first, pull vacuum lines and run through lines for about 20 seconds (will have to put hose in can, and manually rev the engine to keep from dying). Pour rest of contents into tank (full tank) and drive.

4. If you use Pemium fuel, use up what you can (if possible) and switch to regular (or vise versa). Some vehicles don't run well, if at all with Premium fuel.

5. Upon changing fuel filter, make sure all air lines, fuel lines and vacuum lines are not kinked, or have holes in them.

6. If none of the above make a difference, start the truck and locate the MAS (mass air flow sensor) which is between the intake and the air filter. (black); lightly tap on the top of the MAS with a screwdriver handle or a wrench. If the truck stalls (hesitates, stutters) or dies, then it needs replaced. Before replacing however, go to the local parts dealer and purchase a can of MAS cleaner. It is safe for sensors and will clean the sensor inside (honey come inside like a catalytic converter).

Sometimes the MAS is dirty and the sensor isn't able to read the air intake causing it to mix the air and fuel incorrectly. This is a cheap and affective fix for the problem you're having.

If this does not work, try first options above, and this should cure the issue. If not, you may have a timing issue. If you have access to, or own a timing light, use it to determie timing placement is correct. Also, make sure that two of the spark plug wires have not been misplaced. Though it idles fine it will not make too much of a difference at idle but will while driving. I've experienced this first and, and thus I mention it.

Please let me know if you need any further assistance. Here is a tip to get you started. Check with your local parts dealer and find out what the cheapest fix is, and work your way up. 99% of the time it's the simplist components that cause the biggest issues.

Cordially,

carsandcomps
Guru, Premium Expert @ Fixya

Posted on Apr 10, 2010

Ad
aaangie220
  • 202 Answers

SOURCE: clutch replacement 91 pickup 4x4 toyota

ase mechanic:

well depends how strong you are, and if you are using a car lift or doing on your back. either way drain the transfer case fluid, should be bolt on bottom, otherwise when you seperate the transfer case from trans there will big mess. take transfer case off first note how it is mounted with paint marker and then take trans out. much easier then leaving together.

Posted on Jan 29, 2009

  • 563 Answers

SOURCE: how do I replace the driveshaft bearing support?

You jack up the truck, and support it on jack-stands. (no wheel must touch the ground, for safety).
Remove the two front tires for visibility.
Put the tansmission in neutral and apply the handbrake.
Get under the truck and in the area of the support-bearing, mark the position of the driveshaft to the flange, which has 4-bolts.
Remove the 4-bolts.
Pry off the driveshaft with a flat-end screwd-river.
Remove the bolts holding up the support bearing.
Drop it down and pull off the support bearing.
Reverse these procedure for installation.

Posted on Nov 26, 2009

  • 11 Answers

SOURCE: how to replace a clutch in a 95 nissan pickup

hELLO remove your transmission from your truck and unplug all lines and electric wire from it and you will see your pusher plate removed all bolts on the pusher plate and remove the plate and the clutch disc also remove the flywell from the engine and get it refaced from the brake shop and also install a new clutch bearing at the same time,you will have to center your clutch disc when you will install the clutch the way to do it is you put the disc and the pusher plate togeter you install the bolt on the pusher plate snog by hand but dont tight it at this time put the centering toll trought the hole in pusher plate and the disc and center the disc and tight the bolts on the pusher plate at this time and remove the toll(if you remove the flywell those bolts have a torque on it be sure to torque the bolts at the right torque for it refer to a mecanic for it and reinstal your transmission.

Posted on Mar 08, 2010

  • 192 Answers

SOURCE: Can I swap an engine from a '95 Nissan pickup

Yes.. the 2.4 liter configuration will work as the same power plant is in both models. The issue will be the transmission mounting surface on the 4x4 vs the 2x4. You need to insure that the main seal area has same pattern and bolt pattern. YOu will also need to be conscious that the motor you are getting the 2x4 has been broken in on 2 wheel drive and a 4 wheel puts more torque and strain on engine.... so be sure once placed you give a good slow break in process or you could crack the block or crank shaft

Posted on Aug 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch not worhing


Is your clutch master cylinder about empty,your slave cylinder could be bad and leaking,also look for leakage at clutch master cylinder,go to transmission and see if leakage is at slave cylinder,here's how to replace,Here's the part.Here's my 85 Nissan 4x4.

Jan 18, 2013 | 1991 Nissan Pickup

1 Answer

I have a 1995 nissan 4x4 pickup. 4cyl, 5 speed. transmission will not go into gear. it shifts fine into gear but when you let off the clutch it will move maybe an inch before it pops outta gear. the stick...


Could be your clutch slave cylinder is bad,check your clutch fluid,if real low or empty then it is bad,it's located on the side of the transmission with a hydraulic hose connected to it,I have a 85 Nissan 720 4x4 5- speed,had to replace mine a few times.Here's a link on how to do. Repair Guides Clutch Clutch Release Cylinder AutoZone com Here's another link. Repair Guides Clutch Clutch Master Cylinder AutoZone com Here's the new part. Duralast Clutch Slave Cylinder 12425 Read Reviews on Duralast 12425 Your master cylinder probably is good,I just had to change the slave cylinder on mine,unless your's is leaking.If you are in a bind you can add brake fluid,yes it uses brake fluid.Then bleed it then it will get you home,you can get a one man bleeder kit,I have one,here it is. OEM One man brake bleeder kit 25036 Read 17 Reviews on OEM 25036

Jul 19, 2017 | 1994 Nissan Pickup

1 Answer

I have a 96 nissan xe pickup 4x4 standard shift. The gears seems to shift better (not good) when engine is still cool, and the more I drive the harder it is to shift. I have to take clutch petal all the...


Depending how many miles are on the vehicle, the clutch plate may need to be replaced. Do you hear any strange "grinding" noises when engaging or disengaging the clutch? I'm assuming you have checked the hydraulic fluid in the reservoir and it is full. You may also want to change the fluid as hydraulic fluid deteriorates over time and it may not be completely disengaging the clutch. Please rate this answer, thanks.

Feb 01, 2011 | 1995 Nissan Pickup

1 Answer

My 97 nissan pickup v4 4x4 is overheating. I have replaced the thermostat, radiator, clutch fan, and the sending unit. What could still be there problem?


Hello, lilfilop and thank you for asking your question on Fixya!

Here is a simple process that will walk you through a few steps that will pinpoint the overheating problem on your
1997 Nissan Pickup, without even using any tools. It has helped millions of people, and I am certain that it will help you, because I wrote it for people in your exact situation.
How to diagnose your overheating
1997 Nissan Pickup

Get more great money saving tips and tricks about your vehicle from: twitter.com/acoates23234

Thanks for the vote, and good luck!

Dec 29, 2010 | 1997 Nissan Pickup

1 Answer

I have a 95 Nissan 4X4 pickup. I have had this


It seems like you have a bad ground wire or a short.

May 26, 2010 | 1995 Nissan Pickup

1 Answer

I have a '95 pickup 4x4 and am looking for a way


never get your money back out later if you dont do much offroad reduce rubber size smaller tire size.

Feb 24, 2010 | 1995 Nissan Pickup

1 Answer

Truck will not start


does it crank over?
if not then the problem might be somewhere in the starter, starter solenoid, starter relay or wiring

Sep 22, 2008 | 1995 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...