Question about 2008 Dodge Nitro

Open Question

How do I change the brakes on a 2008 Dodge Nitro?

Front brakes

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75117 Answers

SOURCE: Steps on how to change oil filter on 2008 Dodge Nitro

unscrew the old filter, lube the rubber O ring seal of the new one with engine oil and install, tighten 3/4 of a turn from when it contacts sealing surface of engine.

Posted on Mar 05, 2009

  • 202 Answers

SOURCE: emergency brake light comes on while driving

The wire that connects to emergency brake is loose, and grounding out. It probably just needs to be tightened up.

Posted on May 27, 2009

  • 6 Answers

SOURCE: dodge avenger 2008

It depends on who you go to and if you want it done right. I went to the Dealership and had them put front brakes on my 2008 Dodge Avenger and it has been in the shop every 2-4 months since then for front brakes. They replaced the entire front brake system and my 08 Avenger is still eating brakes. I finally took it to a friend who owns a auto repair shop he replace the rotors which are total about 115.00 for each from AutoZone and replaced the brake pads for 50.00 so it cost me just parts 155.00 and my Avenger is running smoothly since haven't had problems with the brakes since. Go to Midas and let them change it for roughly 89.00 avoid the dealership at all cost they can run 200.00-500.00 depending on if it is just the brakes pads or if it is the rotors and pads.

Posted on Jun 02, 2009

  • 191 Answers

SOURCE: 2008 dodge nitro 3.7 engine. The engine missfires

Have it checked for trouble codes sounds like it could be an injector problem or something as serious as a loose rocker,maybe try a crank&cam shaft position sensors

Posted on Jan 04, 2010

  • 113 Answers

SOURCE: where is the oil filter located on my 2008 dodge

You can access the oil filter easily from underneath next to the front, driver-side wheel at the front of the engine. There is clear access to the filter there.

Posted on Mar 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My dodge 2008 nitro brake light switch was changed and now my car won't start.


take it to the ppl that changed it and have them fix it or check your battery,switch,starter or solenoid

Jun 08, 2015 | 2008 Dodge Nitro

1 Answer

Is there a special fuse for my front power window and mirrors on my 2008 dodge nitro


See pages 381 to 388:
http://cdn.dealereprocess.com/cdn/servicemanuals/dodge/2008-nitro.pdf

If can't run windows or mirrors from the driver's side, maybe power switch is defective.

Mar 03, 2015 | 2008 Dodge Nitro

1 Answer

How to change brake light in dodge nitro


remove 1 plastic pin on each side of lights

Feb 16, 2013 | 2008 Dodge Nitro

1 Answer

When I press the brake pedal only the left brake light comes on. The bulbs are good and the fuses are all good. Replace the right light modual but still no help. this is on a 2008 Dodge Nitro


How do you know the bulb is good? Even if it uses the same bulb as the tail light it is always a different filiment. But if you tried replacing the bulb and the fuse than it has to be the wiring. If it's a 2008 it should be covered by the warranty, I would bring it into the dealer.

Aug 17, 2011 | 2008 Dodge Nitro

1 Answer

2008 dodge nitro change oil light how to turn off had oil changed did not go out


Directions are in the book, but you would put the key in and turn it all the way, just don't start engine. Pump gas pedal all the way to the floor 3 times slowly, but it has to be with 10 seconds. Turn key off and when you start again, oil changed chime and warning should not be on. If it is, try again.

May 21, 2010 | 2008 Dodge Nitro

1 Answer

Where is the oil filter located on my 2008 dodge nitro


You can access the oil filter easily from underneath next to the front, driver-side wheel at the front of the engine. There is clear access to the filter there.

Mar 13, 2010 | 2008 Dodge Nitro

1 Answer

Need routing dia for serp belt on dodge 2008 nitro 4.0


If this is a 2008 it should have a decal with the routing on the radiator support across the front of the engine when you open the hood.

Nov 24, 2009 | 2008 Dodge Nitro

2 Answers

Where is the oil filter on a 2007 dodge nitro v6


You can access the oil filter easily from underneath next to the front, driver-side wheel at the front of the engine. There is clear access to the filter there.

For more info on Dodge Nitro, visit the forum at
http://www.dodge-nitro.com/dodge-nitro/

Aug 08, 2009 | 2008 Dodge Nitro

1 Answer

Emergency brake light comes on while driving


The wire that connects to emergency brake is loose, and grounding out. It probably just needs to be tightened up.

May 27, 2009 | 2008 Dodge Nitro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...