Question about 1996 Mazda Millenia

2 Answers

Axle broke car dropped 1996 Mazda can it be repaired

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 5,252 Answers

I take it you don't like low-riders, smirk, smirk. The only axles on front wheel drive cars are the drive axles with the CV joints on each end. Is this what broke? Or was it a rear suspension member? Well, either way, I don't know why it wouldn't be repairable. A well-equipped shop can do wonders from frame straightening (rather doubtful in your case) to restoring to near factory condition. Millenias have a unique suspension system, so be prepared for the possibility of a long parts list for replacement, and the resultant exorbitant repair fee. That's just the way it is nowadays. Dealerships are the most expensive to work with. Ask around and find a good independent shop near you for the best deal. Maybe get two or more estimates of the repair and pick the one that suits you. We may both be happily surprised that the cost of repair was less than expected.
Good luck.

Posted on Feb 23, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 594 Answers

It can be repaired. you will need to make sure you did not bend or crack the shock. usually it will bend so it will also need to be replaced. make sure everything else is good and take both ends of the drIve shaft out of the wheel and the transmIssIon. and replace It. when you Install the new one you wIl need to make It lock Into place or It wIll grInd the gears on the new one.

Posted on Feb 23, 2012

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

joshnaz
  • 186 Answers

SOURCE: 1997 mazda mx6 v6engine the front axle onthe

They are supposed to come out. Any chance of removing the other Axle and seeing if the axle can come out by driving it out with a punch and hammer?

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How 1996 mazda 626 front axle shield broken


The drive shaft has to be removed to replace the rubber boot .you will have to dismantle the CV joint , clean and repack the joint with special grease and fit a new boot.

May 10, 2014 | 2001 Mazda 626

1 Answer

1996 Mazda Protege cv axel removeal


Jack vehicle up use jackstand remove wheel seperate lower balljoint remove axle nut push thru pull strut assembly to side the use prybar between trany and axl n pop it loose n reverse

Dec 24, 2013 | 1995 Mazda Protege

1 Answer

BENT THE RIGHT REAR AXLE ON MY 1996 FORD CONTOUR AND NEED TO KNOW HOW TO REPAIR IT


you don't repair it, you replace it. jack it up, remove the brakes, and all the brake assembly from that axle,, http://www.ehow.com/way_5731956_ford-rear-brake-replacement-instructions.html then remove the bearing cap,, cotter pin, and nut from the spindle , ( you might want to replace the wheel bearing at the same time due to the bad axle ) remove the axle bolts,, and shock bolts, from the axle beam. remove axle beam assembly

Sep 23, 2011 | 1996 Ford Contour

2 Answers

1997 mazda mx6 v6engine the front axle onthe


They are supposed to come out. Any chance of removing the other Axle and seeing if the axle can come out by driving it out with a punch and hammer?

Feb 25, 2010 | 1995 Mazda MX-6

1 Answer

2004 Mazda 6 stuck in Park?


Cable broke? Would still start. Does shifter move at all?

Jan 30, 2010 | 1996 Mazda Millenia

1 Answer

What is the average cost for cv axle repair/replacement?


jack car up the side u suspect and see if there is any play in weal and grab both side of tire push and pull light becare full and dont drop car on you dont tug on like yor trying rip tire of

Jan 03, 2010 | 1996 Chrysler LHS

1 Answer

I hit a curd on the side of my rims i have 275 45 20 i broke 3 studs i replaced all studs and they broke again i do hear a noise everything the wheel turns faster i go the faster the sound and how much to...


If you broke 3 studs when you hit the curb then you can be sure that at the very least you have bent the rim, which will have to be replaced. At the worst you have bent an axle which will have to be replaced. You may have bent the rear end housing as well. This needs to go to a repair shop and be checked over to determine the extent of the problems. Don't put this off, it's very troubling that the studs broke again. Hope this helps.

Sep 27, 2009 | 1996 Ford Explorer

2 Answers

What part do I need to buy to repair a broken axle? It broke at the wheel bearing hub.


if you call a professional junk yard they can help u-if mechanical the librarysec 629 has many tear down manuals

Aug 10, 2009 | 1996 Toyota Corolla

1 Answer

2000 mazda 626 wont shift into gear at all!


Sounds Like You Broke an Axle, And Possibley Broke Something At The Transmission. Good Luck

May 02, 2009 | 2000 Mazda 626

Not finding what you are looking for?
1996 Mazda Millenia Logo

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...