Question about 1995 Toyota Camry
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
I can get you a diagram on monday but it goes from the alternator to the power steering pump then around the tensioner pulley then around the crank pulley then to the a/c compressor then pull on the tensioner to give you some slack and slip it on the waterpump.I hope that helps.Let me know if you still need the diagram
Posted on Nov 29, 2008
malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.
Posted on May 06, 2009
SOURCE: 2005 Toyota Corolla Radio fuse
Pg. 250 of your 2005 Owner's Manual shows the location of the Fuse Boxes. There is one under your hood on the driver's side and the other is under the dash just to the left of steering wheel. Pg 272, will show you how to replace the fuses. Pg. 286-287 gives a diagram and description of each fuse and what part of the electrical system it enables.
This portion of the electrical system correspondeds to the fuse in position 32 on pg. 287 of the manual.
Your going to have to get on your back with a flashlight and open up the fuse box under the dash by the steering wheel. The lid of the fuse box shows the positions of the fuse and their amperage rating. Like I said, replace the fuse in postion 32 (15 Amp). There is a spare 15 Amp fuse in the fuse box under the hood (easy to get to, see the diagrams in the owner's manual). There is also a fuse puller tool next to the spare fuses.
Posted on Aug 11, 2009
Tips for a great answer:
May 30, 2016 | 2007 Toyota Corolla
Aug 23, 2011 | 1995 Toyota Corolla
I am assuming you don't have the owners manual?
you can go directly to the toyota owners website and download a manual, and find the fuse panel diagram for your friends car.
Aug 06, 2011 | 1995 Toyota Corolla
Nov 30, 2010 | 1995 Toyota Corolla
Oct 21, 2010 | 1998 Toyota Corolla
Oct 15, 2010 | Toyota Corolla Cars & Trucks
Dec 15, 2008 | 1995 Toyota Corolla
210 people viewed this question
Usually answered in minutes!