Question about 2001 Ford Explorer Sport Trac

Open Question

Ford explorer sport trac 2001 brake lights not working

Have no brake or bliinker or hazard lights, its not a fuse

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2001 ford explorer sport trac

Just found the answer on another site. Sure enough went out removed the 3 philips head screws in the steering column opened it up and walla a wire connection had pulled itself free. When my son uses my truck he always uses the tilt steering, when I get in I have to readjust it. because of this the wire connection pulled itself out. I simply pushed it back in an blinker and brake light are now working. My husband is now trying to figure a way to secure the wire connection so it doesn't pull itself out again. Hope this helps others, either by saving the cost of a dealership or machanic or from getting rear ended.

Posted on Mar 21, 2009

Ad
chuck943
  • 783 Answers

SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on

Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Posted on Apr 02, 2009

  • 1 Answer

SOURCE: Ford sport trac 2003 brake lights are not working

I know this solution will sound weird but put the steering wheel at it's highest position (untilt) and try it..if they come on it's the a wiring harness in the steering column.

Posted on May 21, 2010

  • 12 Answers

SOURCE: how to change fuel filter on 2001 ford explorer

it in the tank so your gonna either gonna have to drain the tank and lower it to the ground,it shouldn't take more than 30 minutes.make sure you put the seal back in right,so it won't leak,it aint very hard.

Posted on Jul 12, 2009

  • 1 Answer

SOURCE: 01 ford explorer sport trac rear timing chain diagram

They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?

Posted on Nov 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

Hazard lights malfunction


YOU MIGHT HAVE A BURNT OUT RELAY IN FUSE COMPART UNDER YOU CARS HOOD CHECK THAT OUT THRU YOUR CARS MANUAL,IT WILL SHOW YOU WHICH RELAY IT IS?

May 24, 2013 | Cars & Trucks

1 Answer

Rear lights not working on 2002 suzuki grand vitara


In the underdash fuse/relay box, the 15A TAIL fuse feeds power to the coil of headlight relay 2. When the combination switch is set to TAIL, the relay closes and the outer tail lamps light. In the same underdash fuse/relay box, the 20A STOP fuse feeds power to the brake light switch. When the brake pedal is pressed, the inner brake lamps light. The underdash fuse/relay box also contains the 10A TURN BACK fuse which feeds power to the hazard switch and the turn signal relay. Relay output is fed to the combination switch and turn signal power is applied to the selected middle tail light. The fourth fuse in the underdash fuse/relay box is the 15A HAZARD fuse which feeds power to the hazard switch and turn signal relay. When the hazard switch is set, the turn lamps on both sides begin flashing.

Sep 18, 2012 | 2002 Suzuki Grand Vitara

1 Answer

Where is the brake light relay on a 1995 chevy van G20


brake light dont have relay only fuse brakes are hot at all times on gms. in goes from fuse to brake pedal switch to hazard turn signal switch then to brake lights. ck fuse if good go to pedal switch if good go to turn /hazard switch the turn signal hazard brake all use same wire to lamps.

Aug 04, 2012 | 1995 Chevrolet G20

1 Answer

How do I keep fuses for hazards and brake light from blowing


They use the same bulbs in the back.
Check the light sockets and wiring for shorts to ground.

Jun 30, 2012 | Ford E150 Cars & Trucks

1 Answer

Brake light isnt working .. when lights are on brake lights come on ... when brakes are applied.. the light is not bright... nor does my back up light illuminate.. but turn signals do work


make sure that you have the correct bulbs installed and cleanup all the sockets with some WD-40. do your hazard lights work correctly? if not then check the fuse for the hazard/stop light. if its not the fuse then it probably means its a bad turn/hazard switch assembly.

May 14, 2010 | 1995 GMC Jimmy

1 Answer

I have a 85 omni glh I blew my brake lights out I replaced the fuse but they still don't work , everything elae works on the car except the hazards , are the brake lights and the hazards connected...


yes they are. if your hazard flasher is bad and you happen to have the hazard switch turned on your brake lights wont work
put hazard switch in one position and check brake lights
then put in other position and check them
if they work with the hazard switch in one position leave switch olone and check fuses and put a new flasher for hazard in

Mar 24, 2010 | 1985 Dodge Omni

1 Answer

95 gmc jimmie, 4x4, everytime i use my brake pedal, a fuse blows, i have no brake lights, hazard or signal lights. how do i fix it my mom broke off the hazard button in the steerin column so i used a stick...


consider properly repairing the hazard light switch via junkyard parts for a cheap price. You invariably have a short that overloads the fuse when you activate the brake lights via pressing on the brakes.

good luck

Mar 10, 2010 | 1995 GMC Jimmy

1 Answer

My brake, hazard and turn lights dont work, i


well u have two seprate problems the hazards and turn signals have a flasher that needs replacing if the fuse is good on the fuse box marked signals .and there is a brake light switch under the dash board near the brake pedal it has two wires on it check the wires make sure they are connected if so replace the brake light switch

Nov 13, 2009 | 2002 Chevrolet Astro

2 Answers

Brake Lights do not work and hazard button is stuck


I could not tell you how many times people have brought their cars into my shop and tell me that they had already checked all fues and they are OK, then I check the car and find a blown fuse or a fuse that is completely missing.

Your dash (Instrument Cluster) illumination lights are powered by the "PARK LP" fuse in the underhood fuse panel - it is fuse number 37 and should be a 20 Amp fuse. If this fuse is blown, your Park lights on the exterior of the car will also not be working. If they are working and your dash lights are not, then the problem is probably in your headlamp switch.

Your Brake lights are powered by the "STOP LAMP" fuse in the instrument panel (IP) fuse block it is a 15 Amp fuse.

Your Hazzard lights are powered by the "HAZZARD" fuse in the (IP) also a 15 Ap fuse.

If both of these fuses are good, then the most likely problem with your brake and hazzard lamps is the multifunction (Turn Signal) switch.

What any of the above has to do with replacing your window regulators remains a mystery.

Jul 20, 2009 | 2003 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

753 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...