Question about 1987 Dodge Dakota

Open Question

Wiring daigram for ignition system, 1987 dodge Dakota v6 w/ carb.

Is the Hall Effect pick-up upstream or downstream of the ignition coil?

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: 1987 Dakota plugs

Check your 02 sensors and be sure that the air filter is clean. You also may be having trouble with the fuel pressure regulator.

Posted on Aug 25, 2008

Ad
ZJLimited
  • 17970 Answers

SOURCE: 98 dakota 3.9. runs then

P0351 - Ignition Coil A Primary circuit fault.

Could be from Worn Out Plugs to Plug Wires. Also can be dirty injectors.

Just do a routine maintenance, Oil, Fuel and Air Filters, Oil change, new plugs and wires and add a bottle of Techron on a full tank of gas. If none has been done. Perhaps needs some maintenance.

Also, I suggest check your fuel pressure, if it is low you can do some simple checks to see why. Pinch the return line. If the pressure raises to at least the correct fuel rail pressure, then the regulator is the problem. if it does not then you should check for a clogged fuel filter. If pressure is still low you probably have a weak pump, low voltage to the pump, or a restricted fuel supply line.

Keep us updated and send us your comments.

Posted on Nov 09, 2010

ZJLimited
  • 17970 Answers

SOURCE: where can i find a

I suggest check this for your 1987 Dodge Dakota 3.9 liter V-6 VIN "M"

zjlimited_588.gif



Hope helps' remember to rate and comment this free answer.

Posted on Aug 07, 2011

emissionwiz
  • 76164 Answers

SOURCE: wiring ignition system, hall effect electronic ignition system. ignition coil, pick-up coil no spark at the coil or the distributor cap. any idea or perhaps a diagram of the wiring. it's a 1991

We do not have wiring digrams here but you can access them and all the factory service information here for a small fee.

Posted on Nov 04, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Dodge Dakota,3.9,V6, ignition coil wiring diagram


I think yours has an ignition module which can be checked at parts store. Could also be bad coil. If you must have wiring diagram, get shop manual.

Mar 09, 2014 | 1996 Dodge Dakota

1 Answer

I have a 1989 dodge dakota truck with a 3.9L. there is no fire going to the coil. i have replaced the module and the coil. still won't start. I get code 34 please help me to diagnose this problem. thanks


Replace the Automatic Shutdown Relay. If that doesn't fix the problem, the other place I would look, would be the Hall Effect Switch inside the distributor. You should be able to change this part without removing the distributor. If the computer doesn't get a signal from the Hall Effect, it will shut down the ASD, which supplies power to the coil and the fuel pump.

Feb 19, 2011 | 1988 Dodge Dakota

1 Answer

I have 1998 dakota cranks but no start no spark how do I check?


Do you hear the fuel pump when you cycle the key?
If not, then Check the ASD - auto shut down relay ,under hood, drivers side,distribution box
Only got computer,crank sensor,and coil
The distributor hall effect sensor, is for the injector timing,do not move the dist.,

Is the ignition switch and neutral switch okey

If you got no wiring diagrams or experience with a volt meter,your in a tough spot.

Nov 08, 2010 | 1998 Dodge Dakota

1 Answer

I have no spark from the coil changed crank sensor and checked to see if the distributor sitll turned and it did when rolled over


try changing the hall effect sensor. this is the round plastic part under the distributor rotor with about a six inch wire coming out of it with a three prong plug. If you go to the parts store and they are having trouble looking it up have them look under the name pick up coil. Have you checked the ignition coil?

Nov 01, 2009 | 1993 Dodge Dakota

2 Answers

Engine quits after 3 or 4 miles of driving


I would think either a bad coil, or ignition module,or fuel pump. Sometimes the big relays for these system can cause this symptom so rotate the important ones in the engine compartment. Also if yours has an ASD relay this is your main power one.

Sep 06, 2009 | 1994 Dodge Dakota Club Cab

2 Answers

96 Dodge Dakota .....NO SPARK


you should have power on one terminal of the coil connector when cranking engine,i prefer using a test light..put the lead of your test light on battery positive and check other coil connector terminal..it should flash/pulse..if it is,you need an ignition coil..if not,you may have an engine controller problem..also check harness near controller and fuseblock for corroded wires..controller may not be powered up properly

May 29, 2009 | 1996 Dodge Dakota

1 Answer

1997 Dodge Stratus V6 oxygen sensor location


Upstream, as in ahead of the converter, back toward engine. Start at converter and work your way back, should be on exhaust pipe or even on manifold.

Jan 11, 2009 | 1996 Nissan 240SX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...