Question about 1999 Pontiac Sunfire
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
where door latches on car get a screw driver and pop latch back in the up possion right now your latch is down like your door is closed
Posted on Nov 17, 2008
See if you can make the latch work by just using a screw driver in the slot to lock it, then open it with the key. If that works ok, you will need to raise the striker and align it to the latch.
Posted on May 22, 2009
my 1999 pontiac sunfire drivers door latch is broke can not close the door. i have it pulled shut? how much will a used latch cost, or even 3 bolts for it? all the auto stores/ jumk yards are closed for me to call
Posted on Aug 01, 2009
The engine size don't matter except when you order the parts. First you will want to chock the rear tires. This is a front wheel drive, when you jack the front, park wont work. you should also set the parking brake.
You will want a metric socket set and rachet, and a fairly large flat head screw driver.
Remove the wheel.
When you look at the brakes, you should see 2 bolts holding them on, If they have a star shape that looks like a screw driver might fit in it, it is a torx bit, you will need to replace the wheel and go get one. The guy at the parts store should be able to tell you what size.
I'm pretty sure it is going to be a regular hex nut, probably 12 or 13mm.
You can loosen them, but don't remove them yet.
First you need to depress your caliper. This can be done a couple ways.
I just insert a screw driver between the pad and the rotor(the shiny thing that the pads make contact with.) Carefully pry the inner pad slowly away from the rotor. Don't scratch the rotor, you can dig into the pad all you want, your putting new ones on.
Once the inner pad is all the way in, then you can remove the bolts and the caliper will slide out.
Remove the old pads and replace with the new.
Put the caliper back on, make sure you get the bolts tight.
Do the other wheel the same way.
The other way to get the caliper pushed in, by the way.
Remove the bolts, remove the caliper from the rotor, Use a large "c" clamp to depress the cylinder.
P.S. Do not under any circumstances remove your brake lines.
When you are finished with brakes and have tires replaced....
Caution!!! Before you start your car, pump your brakes a few times. Check your brake fluid. You more than likely wont need any, but you should always check it.
Also, do not add brake fluid before replacing pads, the level is going to be higher with new pads.
Back brakes will be similar if it is disc, if it is drum, do your self a favor and have some one else do it or get a service manual. I could walk you thru it, but you need more tools and you have to adjust them....
Better to pay $100 or so and have it done right.
Posted on Feb 19, 2010
kinda of oil,, should be on oil cap,,5-20 or 5-30,,10-30,,oil with out filter change,,4qts,,with filter 4.5qts,,that mean four & a half quarts only,,always ck ur oil stick for oil level,,
Posted on Mar 14, 2010
Tips for a great answer:
Sep 17, 2011 | 1997 Pontiac Sunfire
May 20, 2011 | 1999 Pontiac Sunfire
Jan 04, 2011 | 1997 Pontiac Sunfire
Oct 19, 2010 | 1999 Pontiac Sunfire
Aug 11, 2010 | 1998 Pontiac Sunfire
Jan 15, 2010 | Pontiac Sunfire Cars & Trucks
Jan 11, 2009 | 1997 Pontiac Sunfire
Nov 17, 2008 | 1997 Pontiac Sunfire
203 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: