Question about 1998 Acura RL

Open Question

How to replace an idle air control valve on a 1998 acura rl?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
66 chrgr
  • 1011 Answers

SOURCE: how do i turn off the maintenence required light

the odometer trip setter, find it on the dash hold it in,then turn the key to the on position it will flash and then go out .it takes about ten seconds.

Posted on Mar 07, 2009

Ad
roniecon
  • 6927 Answers

SOURCE: where is low pressure port located on 1999 acura

look for the large ac line/hose and follow it untill u come to the small service port this is wher u charge the small ac line/hose has the large port this is the high side

Posted on Jun 30, 2009

  • 580 Answers

SOURCE: Heater/Cooling problems on 2000 Acura RL

Check the fuse for your blower motor if it is OK the Blower Motor may be bad or you may have a loose wire to or from the it have it checked if fuse is good

Posted on Jul 09, 2009

  • 1 Answer

SOURCE: need radio code for 1998 acura rl. serial #

if you pop out the center button under the radio you can use a flash light and get the code under the radio

Posted on Oct 24, 2009

  • 97 Answers

SOURCE: How to remove factory radio acura rl 99

the best and safest way to remove this radio is with the special tools that Acura made specifically for removing the radio. Any radio store or best buy can easily remove it for you. I hope this helps please rate this and thank you.

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What make my 2005 Acura RL AC blow out heat not cold air


There could be several causes. Someone will need to do some more troubleshooting to determine the likely cause. For example, it could be low on R-134a in which case the A/C compressor clutch would either not engage or might cycle rapidly. The blend door could be broken, causing air to always flow through the heater core. Or, your RL might use an electronic flow valve to shut off coolant flow to the heater core, and that valve could be failing. The HVAC control module may be functioning incorrectly and always calling for heat. Or one of the temperature sensors may be faulty and telling the HVAC control module that the vent temperature is colder than requested and therefore it provides more heat.

Sep 21, 2017 | Acura Cars & Trucks

1 Answer

1997 acura tl fuel system diagram


On this website, you find fuel controls wiring diagrams for Acura TL (1998)

Acura TL 1998 wiring diagrams fuel controls

Feb 09, 2013 | 1998 Acura RL

1 Answer

Bleeding air from cooling system on 1999 acura rl


Its a Honda...just burn the heap of junk..you will get plenty of heat that way!!

Jan 01, 2012 | 1994 Acura Legend

1 Answer

MY 1998 ACURA WONT START TURS BUT WONT START ALLREADY REPLEASE START


1998 acura rl replace fule pump, and check fule relay main and it was good, but still no fire to sparkplugs

May 11, 2011 | 1998 Acura RL

1 Answer

I have a 1998 Acura 3.0 CL and the radio had an error 3 last week. I had to take the console and radio out in order to find the radio serial number and got the radio code from Acura, since mine was...


I don't see this as related to the console. This issue is usually caused by the idle air control valve. The valve may be bad or possibly the wiring. If it's the wiring, normally the computer will turn on the engine light.
You can check the valve operation using a common obd2 scanner in data mode.
Here is more info from autozone.com:
Engine idle speeds are controlled by the PCM through the Idle Air Control (IAC) valve mounted on the throttle body. The PCM sends voltage pulses to the IAC motor windings causing the IAC motor shaft and pintle to move in or out a given distance (number of steps) for each pulse (called counts). The movement of the pintle controls the airflow around the throttle plate, which in turn, controls engine idle speed. IAC valve pintle position counts can be observed using a scan tool. Zero counts correspond to a fully closed passage, while 140 counts or more corresponds to full flow.
Idle speed can be categorized in 2 ways: actual (controlled) idle speed and minimum idle speed. Controlled idle speed is obtained by the PCM positioning the IAC valve pintle. Resulting idle speed is determined by total air flow (IAC/passage + PCV + throttle valve + calibrated vacuum leaks). Controlled idle speed is specified at normal operating conditions, which consists of engine coolant at normal operating temperature, air conditioning compressor OFF, manual transaxle in neutral or automatic transaxle in D .
Minimum idle air speed is set at the factory with a stop screw. This setting allows a certain amount of air to bypass the throttle valves regardless of IAC valve pintle positioning. A combination of this air flow and IAC pintle positioning allows the PCM to control engine idle speed. During normal engine idle operation, the IAC valve pintle is positioned a calibrated number of steps (counts) from the seat. No adjustment is required during routine maintenance. Tampering with the minimum idle speed adjustment may result in premature failure of the IAC valve or improperly controlled engine idle operation.

TESTING The IAC can be monitored with an appropriate and Data-stream capable scan tool

Oct 02, 2017 | 1998 Acura CL

1 Answer

Where can I locate the PGM-F1 relay and what process would I have to do to replace the fuel pump on a 1998 Acura RL?


Most acura and hondas have the fuel pump relay on the drivers side kick panel. It is bolted down to the sheet metal it is black and brown in color.

Jan 21, 2010 | 1998 Acura RL

1 Answer

1998 Acura 2.3cl will not idle


idle control valve is either blocked or damaged this controls engine at low revs or idle, removing the pcv is just letting more air into the fuel system, but this will not be controlled airflow. this is the under side of the idel control valve
underside_with_valve-02v24stlnrwd2v1pzef3romw-4-5.jpg top centre is the wiring connection, this is what needs cleaning or replacing. they more than likely just needs a good clean, also clean the MAF and replace the air filter as if this part stops working there has to be a reason from the air intake. MAF use MAF cleaner only. idle valve clean with carb cleaner give it a good soaking, and shack out an flush again do this a few times and then shake it out then spray loads inside and leave to soak. for about an hour and shake out the rest a flush it one last time. and leave to dry. then refit. when no more dirt comes out.

Jul 04, 2017 | 1998 Acura CL

Not finding what you are looking for?
1998 Acura RL Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

79851 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...