Question about 1998 Ford Econoline

Open Question

Where is the egr valve on a 98 ford e350 5.4l van

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

iadame
  • 676 Answers

SOURCE: can't find fuel filter on 2004 ford e350 van

Should be on inside of frame just behind the driver door. You will need the tool to pull off lines.

Posted on May 08, 2009

alicantecoli
  • 22095 Answers

SOURCE: egr valve on ford 98 ranger, ck. eng. light on

disconnect it and seal it off with a piece of broom handle in the inlet side.sounds drastic i know but it works.

Posted on Mar 04, 2009

jaysonemanme
  • 500 Answers

SOURCE: my 2004 ford freestar van is hesitating going down

most likely not the fuel filter- try plugs and wires... could be a number of things, if the vehicle runs fine while in park and doesnt hesitate, most likely is sprk plugs and wires or a transmission problem...

Posted on Jun 25, 2009

  • 1 Answer

SOURCE: 2003 ford van e350 rear air vent is not blowing

Try this article. I have the same problem and I think it is the vacuum motor that controls the door for changing from hot/cold in the rear heater box (located inside behind the L rear wheel)

https://www.fleet.ford.com/truckbbas/non-html/Q19.PDF

Posted on Jul 22, 2009

  • 432 Answers

SOURCE: i have a 98 ford windstar 3.8 with a engine miss

I replaced the coil pack on my friends wind star when they had a mis. If you take the sparkplug wires loose and just set them on the plugs loose it will be easy to remove them with the engine running. Useing plastic plyers or some kind of insulated grabers, one by one take the wire away from the plug/or coil and see if it makes a difference.Take it away then put it back then go to the next one.If it runs the same when the wire is off then you probably will not hear a spark at that wire. The coils do go bad on alot of newer cars.
I hope this info helps you.

Posted on Sep 25, 2009

Testimonial: "thanx for the info i'll try that. thanx again."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 cantour svt code 401


It basically indicates a problem with the EGR valve or the DPFE sensor. Usually, this is caused by blocked passages in the EGR system, not with the EGR valve or DPFE sensor themselves. To clean them, you will have to remove the throttle body.

Mar 25, 2013 | Ford Contour Cars & Trucks

1 Answer

Egr valve,van losing power,do i have to replace the egr valve or can this one be fixed.


if it is a ford 6litre diesel there is a egr delete kit available at the dealer

Oct 30, 2011 | Cars & Trucks

1 Answer

OBD II code PO401 EGR Problem? Change Solenoid and pressure sensor; egr valve working good. Pressure sensor have 5 volt reference and ground; solenoide have 12 volt in red cable and negative is ok. Ford...


The EGR solenoid hardley ever goes out..Probably a flow problem,,If its the 4.2 its more than likely the EGR ports...Please list the engine..I may know what to tell you to fix it..

Sep 14, 2011 | Ford E-250 Cars & Trucks

1 Answer

1999 ford econoline van both rear doors are locked and cannot open from inside or out?


I have a 1999 Ford e150 van and the van runs good on the highway and rough on the city street. tries to stall at red lights and stop signs. I took it to a garage and the computer says it is running lean on both banks.

EGR sensor, just replaced it an hour ago and started to remove the egr valve. I can't figure out how to get out the bottom bolt. and is there anything else holding the egr valve?

The garage said to use carb cleaner and spray it out. they told me to ry this before you buy a new one. It's 11:30 pm and I wish i would have just got a new one. I don't want to go through this again.

Help me get this off and if possible direct me to some photos,

Thanks,

Bob
videoguybob@mail2bob.com

Mar 04, 2011 | Ford Econoline Cars & Trucks

1 Answer

What is diagnostic code p0405 for 98 chev ast van


Code p0405 is for faulty EGR vave or some of the pipe/lines going in or out of EGR valve/system hase broke, leaks or fall of. Or egr valve is dirty and stuck. Check EGR valvle!

Dec 03, 2010 | Chevrolet Astro Cars & Trucks

3 Answers

I have a '98 Astro van that starts fine when cold but is hard to start win hot. It idle and runs fine. After it cools down completely, it will start OK. I was told it could be a fuel pressure problem and...


I agree, replace the Coolant temp sensor, it will have 2 wires going to it, Not 1. Usually located just behind the breather near the thermostat outlet.

This sensor controlles your timing and fuel to air ratio.

May 28, 2010 | 1998 Chevrolet Astro

1 Answer

Start up 1996 ford windstar ,runs great,get the van up to operating temp,shut off van and try to restart 15 mins later its very hard to start.....if you leave it and come back when it's cold it will start...


Not your camshaft sensor, it would not even start. Your going to have to get it scaned, but I'm thinking it may be your EGR system.

If you are comfortable performing some basic checks prior to resorting to the Ford Dealer then try pulling a vacuum on the EGR valve to make sure the pintle moves freely in both directions. While you're at it, make sure all vacuum hoses and system components hold a vacuum. Inspect the EGR valve visually for coking and contamination. Check EGR solenoids and the position sensor for electrical continuity.

Good luck and hope this helps.

Apr 13, 2009 | 1996 Ford Windstar

1 Answer

Check engine light won't go off to pass inspection


No Biggy.. Get them to install a DPFE sensor,, ( its the one that regulates the EGR valve ) Most ppl mistake a 1409 Code as Being EGR and it is kinda.. but when the valve maint fails.. its almost always the DPFE sensor.. Try that and lemmie know

Mar 11, 2009 | 2001 Ford Windstar

1 Answer

Egr valve on ford 98 ranger, ck. eng. light on


disconnect it and seal it off with a piece of broom handle in the inlet side.sounds drastic i know but it works.

Mar 04, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?
1998 Ford Econoline Logo

Related Topics:

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5474 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...