Question about 1998 Mitsubishi Diamante

Open Question

How to remove ebrakes cables, without cutting

Posted by on

  • rick
    rick Feb 22, 2012

    if you are trying to take out the cables to reuse them the best way is to remove them from the lever inside the car first and that will give you freeplay to remove them from the calipers easier

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to unhook the emergency brake cable on the rear end passenger side of a 2000 Chevy Suburban?


up under the truck by the drivers side seat area will see a 1 into 2 cable with adjustments loosen the connection and that will slacken the ebrake cable so you can remove the connection

May 13, 2017 | Cars & Trucks

1 Answer

How to I repair my shift gears on my Chrysler 2007 Sebring? It's stuck in park.


I assume this is a floor shift,remove shifter knob, pry the trim around the shifter up to remove to get to the 2 screws there, in the storage compartment there may be 4 screws, pull Ebrake up as far as you can then rear of console upward over ebrake handle then back,remember you have to reverse what you just did to put it back together. If your after the shift cable try to pop it off the trans first to see if it can be moved out of park at the trans if so more likely is the cable if not you may have internal trans problem.

Dec 27, 2014 | 2007 Chrysler Sebring 2.7

1 Answer

I need to tighten the emergency brake cable,where is the place where the brake cable is tightened?


Hello, There are really two things to do. There is an equalizer adjustment in the rearward part of the cable to make both rear wheels operate evenly. Put on the Ebrake lightly and see if both rear brakes are applying even pressure. Adjust until they are balanced.

Then push down fully on the Ebrake lever until tight, then push down, repeat and the Ebrake reel under the dash will draw in the extra slack.

Jul 04, 2011 | 2002 Ford Explorer

1 Answer

My ebrake is locked cant push it in and my right rear drum wont turn or come offf


sounds like the cable is frozen if you need to move now you can cut this cable to the wheel which will release the wheel dont recomend this but will do in a pinch

Feb 09, 2011 | 2005 Dodge Grand Caravan

1 Answer

Parking brake not working


you will need to remove the wheels and drums check ebrake cables and brake shoes, make sure the arms are connected and not frozen and also brakes are adjusted correctly,most times its a bad cable or frozen hardware to the ebrake. hope this helps.

Sep 07, 2010 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Cannot get the rear rotor off on the driver side, does the emergency cable assembly affect the removal of the rotor? it is very tight and will not budge


Yes it can affect removal. You may need to rachet the starwheel down to clear any grooving inside the Ebrake drum. Then try to loosen the Ebrake cables. If you have a threaded adjuster on the cable try to loosen it. Or try pulling slack from the underdash brake assembly where it comes out to join the main cable.

I sometimes have to use a visegrip plier and clamp what I have wrestled from the inside of the car. Be sure to use penetrating oil on the studholes and axlehole to free the rust from the rotor.

Aug 15, 2010 | 2001 Mercury Grand Marquis

2 Answers

2000 VW Beetle ebrake needs adjusting, ebrake light goes off too


when you put the rear calipers back you didnt reset the e brake tensioner tight enough......hence the extra clicks.....

Jul 21, 2010 | 2000 Volkswagen Beetle

1 Answer

Need to remove ebrake bracket to remove last bolt for gas tank removal, not sure how to remove ebrake line/cable. Any help would be helpful Thanks in advance!


if theres no bolt to remove the only thing i can say is try to bend then bend back but most brackets like this are bolted on//oz

Sep 23, 2009 | 1998 Chevrolet S-10 Pickup

3 Answers

How to tighten uo the hand break cable on my bmw


You'll need to remove the center console that is over the hand brake. (screws and clips will most likely be hidden)
Once the console is off, you should be able to see two cables connecting to the base of the lever (one cable on the left of the lever and one to the right as these control the ebrake on their side of the car respectively.
Loosen the nut and you can shimmy the cable to tighten it.
Don't do it too tight or your ebrake may be engaged even though the lever is all the way down.

Sep 09, 2009 | 1996 BMW 318

1 Answer

My ebrake cable is stuck on my 2001 jetta any ideas short of cutting it lol


safely go under the car, or reach under the car and holding on th the cable, pul like heck on it, jerking on it several times, both sides. Make sure the wheels are blocked and the engine is off.

Aug 27, 2009 | 2001 Volkswagen Jetta TDI

Not finding what you are looking for?
1998 Mitsubishi Diamante Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...