Question about 2005 Renault Laguna II

1 Answer

Dual mass flywheels

How to fit and torque settings

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

For light vehicle, recommended torque is 45 newton meter and an additional 3/4 turn of the wrench and for 6 bolts tightening sequence should be 3 by 3 as star delta.

Posted on Feb 22, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced transmission now it will not start


some vehicles have crank angle sensor fitted to belhousing, by removing trans can damage the sensor or may be forgot to connect the socket. also if its a manual and has a dual mass flywheel then excessive play on dual mass can upset the crank angle sensor timing

Apr 06, 2013 | 1997 Chevrolet Suburban

1 Answer

Grinding in tranny after replacing clutch


Did you remember to torque all of your clutch plate bolts? Flywheel bolts?

May 04, 2010 | 1996 Ford F250 Crew Cab

1 Answer

Starter motor is jamming


NO,when the dual mass flywheel goes you will feel it.starter motor jamming is normally down to worn teeth/release spring.

Apr 26, 2010 | 2001 Ford Focus

1 Answer

When fitting a new dual mass clutch, how do you know which way to bolt it on as the holes are not offset in any way


Align the dowel pin on the crankshaft to the smallest hole on the dual mass flywheel.

Jul 22, 2009 | 2002 Nissan Xterra

2 Answers

96 FORD F-350 7.3 TURBO DIESEL 5 SPEED


no, it shouldnt have any looseness to it and dual mass flywheels are VERY expensive to replace, BUT yes it can be converted to a solid flywheel, check out autozone.com part number MU1989 or advanceautoparts.com part number 798, that should get you on the right path to curing your problems, i welded the two independantly turning discs of my dual mass flywheel together but i wouldnt recommend anyone doing that without the proper equipment to do so (i.e. precision lathes, cast iron welding rods, etc)

Mar 29, 2009 | 1996 Ford F350 Crew Cab

1 Answer

Need torque settings for dual mass flywheel in 3.0 isuzu trooper


diesel 4JX1 engine
apply engine oil to threads
1st- 59Nm(43lb ft)
2nd- 60-90deg.
3rd- 60-90deg.

Jan 03, 2009 | 2001 Isuzu Trooper

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond


Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
PARTS ASSEMBLY:
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
2005 Renault Laguna II Logo

269 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

xxxxxx xxx

Level 3 Expert

4836 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...