Question about Cars & Trucks

Open Question

How to replace a headlight bulb on a 2008 toyota Avalon

What do I need to do to replace a headlight bulb

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 76 Answers

SOURCE: Replacing 2000 toyota avalon fog light bulb

o easy enough just jack frontcar up use jackstand for safety now loo up under the bumper where fog lights sit depending on style fog light u might need to pull the whole assembly out or just twist the bulb not a hard task once u see it from underneath it is pretty easy

Posted on Dec 02, 2008

Ad
  • 840 Answers

SOURCE: 2002 license plate bulbs

its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Posted on Feb 02, 2009

LEFTY64
  • 69 Answers

SOURCE: I need to replace the headlight on my 1994 Toyota Pickup

CAUTION Most headlight retaining rings and trim bezels have very sharp edges. Wear gloves. Never pry or push on a headlamp; it can shatter suddenly.

  1. Make sure the headlight switch is in the off position.
  2. Loosen the parking and side turn signal unit retaining screws. Then remove the units unplugging the connectors.



0900c15280061083.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: After removing the parking lamp screws, push on the grille clips to release the grille from the truck
  1. Next, open the hood to gain access to the grille clips. Using a flat-bladded tool, push on the clips to release them and the grille.



0900c15280061084.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Remove the grille from the truck and set aside
  1. The sealed beam is held in place by a retainer and either 2 or 4 small screws. Identify these screws before applying any tools.DO NOT confuse the small retaining screws with the larger aiming screws. There will be two aiming screws or adjustors for each lamp. (One adjustor controls the up/down motion and the other controls the left/right motion.) Identify the adjustors and avoid them during removal. If they are not disturbed, the new headlamp will be in identical aim to the old one.



0900c15280061085.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Remove the headlight bezel which is secured by screws
  1. Using a small screwdriver (preferably magnetic) and a pair of taper-nose pliers if necessary, remove the small screws in the headlamp retainer. DON'T drop the screws; they vanish into unknown locations.



0900c15280061086.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Be careful when removing the headlight bezels, they can be sharp
A good kitchen or household magnet placed on the shank of the screwdriver will provide enough grip to hold the screw during removal.
  1. Remove the retainer and the headlamp may be gently pulled free from its mounts. Detach the connector from the back of the sealed beam unit and remove the unit from the car.



0900c15280061087.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 5: Pull the light out, then unplug the wiring harness from behind it

Posted on Apr 07, 2009

  • 1 Answer

SOURCE: Passenger Low Beam Headlight needs replacement!!!

You could remove the air filter cover and then you will be able to reach the bulb.

Posted on Apr 22, 2009

  • 157 Answers

SOURCE: How do you replace the headlight bulb on a Toyota Corolla 2003

You can and it is not difficult, there are two bolts holding the top of the headlight to the body just over the radiator and a couple of screws holding the indicato in place, but you can access the back of the light fitting without doing so . It is a bit of a squeeze on the battery side.

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the low beam headoght


You need to remove the inner fender liner to access the bulbs. Here is a video explaining how. You must suffer thru a Sylvania Ad first...sorry.


Headlight Change 2005 2012 Toyota Avalon 2008 Toyota Avalon Limited 3 5L V6

Oct 22, 2015 | 2008 Toyota Avalon

1 Answer

Show me how to replace the dim headlight on my 1997 toyota avalon


GO AND DOWNLOAD YOUR REPAIR MANUAL:
http://www.repairmanualdownloads.com
sincerely,
ERNESTO CUADRAMANAGUA, NICARAGUA

Dec 14, 2011 | 1996 Toyota Avalon

2 Answers

Cleaned the snow off the Avalon and noticed a loud pop and the right highbeam light had blown out. Within 10 minutes as driving heard the left highbeam light blow out. Never had this happen with any...


There is a Technical Service Bulletin regarding the high beam bulbs on the Avalon. TSB# 0044-10, NHTSA# 10033406. Mind you, this is not a recall, so any repairs the dealer makes will cost you dearly. Since the high beams are standard halogen bulbs, I would recommend that you replace them yourself with Sylvania long life bulbs. If the dealer replaces the entire assembly, it may involve the HID low beams to the tune of $1000 or more. You can contact your dealer and ask for information about the tsb, all the dealerships received the tsb. If he offers to repair it in accordance with the tsp, get it in writing that there will be no charge.

Dec 26, 2010 | 2008 Toyota Avalon

1 Answer

Need to replace headlight bulb. how do I access bulb?


There are 3 bolts around the headlight and if u remove these u can give the headlight a good tug to remove it and access the bulb

Dec 17, 2010 | 1997 Toyota Avalon

2 Answers

High beam headlights not working


Hello chinson. When the highbeams are not working, the problem is usually the switch. Since this is a 2008, your warranty will probably be in play. Contact your Toyota dealer before you do a self-repair. Joe

Thanks for choosing Fixya

Nov 21, 2010 | 2008 Toyota Avalon

1 Answer

Toyota avalon 1998


Unplug the connector, and rotate the bulb 1/4 turn. Pull straight back.

Oct 04, 2008 | 1998 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...