Question about 1998 Honda CR-V

Open Question

How do i fix the ignition switch in a 1998 honda crv

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mythman
  • 84 Answers

SOURCE: 1998 honda crv vibrates when starting out

Increased vibration from a vehicle indicates worn out engine supports. This vibration often disappears when revving the engine high, but is very noticeable at low revs.

You can have these inspected and possibly replaced to reduce the vibration cominf from your engine.

Hope this helps.

Posted on Jul 02, 2009

Ad
satitus
  • 273 Answers

SOURCE: Clock does not work. crv 1998

If it is not the fuse then it is most likely an internal issue with the clock itself. These clocks (and many other models) commonly burn out internally. I offer a very cost effective repair solution. Check it out!
www.autoclockrepair.com

$200 less than the dealer and a lifetime guarantee

Posted on Jan 30, 2010

johnjohn2
  • 5763 Answers

SOURCE: replacing cruise control bulb on honda crv 2006

JUST POP SWITCH OUT AND BULB GOES INTO SWITCH USE SMALL SCREW DRIVER TO REMOVE YOU WILL HAVE TO TWIST IT COUNTERCLOCKWISE TO REMOVE, TWIST CLOCKWISE TO INSTALL.

Posted on Apr 21, 2010

  • 4 Answers

SOURCE: 2001 Honda CRV, key stuck

Is the gear in P position?

Posted on Oct 07, 2010

  • 2 Answers

SOURCE: 1998 Honda CRV stalls once it warms up then after

Also try the crv recall replacing the ignition mechanism where you insert the key. I have the same problem and was solved after reading about it in one blog.. it is free. It appears that it got shorted and will automatically kill the engine. after a while it will be cold again and you will be able to start the engine..

Posted on Nov 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Recently my 1998 Honda CRV cut out would not restart. Ignition switch was replaced.After about 15 kms vehicle cut out again. Could not restart. Any advice on the problem?


Either the ignition switch wasn't the primary fault or whoever changed it for you did something wrong - either way you paid good money to have a car that works and it doesn't so return it to the repairer and tell them to get it right this time...

If there is an on-engine electronic fault there will be a code stored in the memory.

Feb 20, 2017 | Honda Cars & Trucks

1 Answer

The battery in my 1998 Honda CRV works fine. Had a problem with the key sticking, now the key turns in the ignition but won't catch to start the car. Not sure what to do


Sounds like the ignition switch is worn out(or the linkage from the lock cylinder to the switch has come loose or something like that)

Oct 08, 2012 | 1999 Honda CR-V

1 Answer

Honda crv 1998 dont start


check your fuel pump.if it swings and dont want to start.if it does not swing then check the ignition switch.it can be faulty and your battery.

Aug 30, 2012 | 1998 Honda CR-V

1 Answer

1998 Honda CRV Drivers side window(power)


Did you check for power and ground at the window motor connector before you replaced it? Apparently not....

May 16, 2012 | 1998 Honda CR-V

2 Answers

1998 Honda CRV stalls once it warms up then after


You need to replace your coil pack. It sounds to be over heating which results in no spark being sent and the enige dies. Very common fault and easily fixed.

Dec 17, 2009 | Honda CR-V Cars & Trucks

1 Answer

Honda crv 2000 computer reset


Ok,
1. ensure ignition off
2 . bridge the 2 pin connector, Put a piece of wire across both terminals
3.switch ignition on
4. SRS lamp should illuminate for 6 seconds
5.disconnect the bridge wire within 4 seconds of the warning lamp extinguishing
6.SRS lamp should illuminate 2 times, Codes erased
7.switch ignition off
8 Wait 10 seconds. switch ignition on and check SRS warning lamp operation.
hope this helps

Feb 18, 2009 | 2006 Honda CR-V

3 Answers

98Crv- shuts off when I'm driving 70mph...


danm my crv does exaclty wat u guys are talking about but the dealership wont give me a solution straight answer

Jul 23, 2008 | 1998 Honda CR-V

Not finding what you are looking for?
1998 Honda CR-V Logo

Related Topics:

412 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...