Question about 1983 Buick Regal

1 Answer

Does the engine oil dipstick tube,where it goes into the oil pan, have a gasket or an o - ring that is supposed to keep it from leaking? I just changed my oil pan gasket and noe it looks like there is oil coming out from the base of the dipstick and onto my oil pan all the way to my exhaust manifold.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 5,370 Answers

For more oil and oil pump details check out the direct links below: ---

How to Replace Oil Pan on car?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-oil-pan-on-audi-a4-and.html
--------
How to Replace an Oil Pan Gasket?
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html
-----------
HOW TO REPLACE AN OIL PUMP
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html
----------
HOW TO CHANGE ENGINE OIL AND FILTER
http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html
----------
HOW TO REPLACE AN OIL PRESSURE SWITCH (SENSOR)
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html
-----------
How to Check Differential Oil Leaks and Replace Oil
http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html
----------
HOW TO PERFORM A BASIC ENGINE TUNE UP-OIL CHANGE
http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

-------


Oil pan Gasket on car?
http://howtobyme.blogspot.com/2011/11/oil-pan-gasket-on-1998-toyota-tercel.html

---------

Oil pressure for car?

http://schematicsdiagram.blogspot.com/2011/12/oil-pressure-for-2001-gmc-jimmy-v6.html

----------
How to replace Oil Pan on car?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pan-on-2008-honda.html

---------
How to replace Oil Pressure Sensor on car?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pressure-sensor-on.html

-----------
How to replace Oil Pump on car?

http://howtobyme.blogspot.com/2011/12/how-to-replace-oil-pump-on-2008-honda.html

----------
Car oil leak?

http://schematicsdiagram.blogspot.com/2011/12/car-oil-leak.html

----------
Car oil leaks from valve cover gasket?

http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

----------
Oil light blinks on dashboard?

http://schematicsdiagram.blogspot.com/2011/12/oil-light-blinks-on-dashboard.html

-----------
Oil pressure issues on car?


http://repairhelpcenter.blogspot.com/2012/01/oil-pressure-issuers-on-toyota-tundra.html

-----------
Oil leaks from air filter on ford?

http://technoanswers.blogspot.com/2012/01/oil-leaks-from-air-filter-on-ford.html

---------
Wire running from oil pan to alternator?

http://technoanswers.blogspot.in/2012/02/wire-running-from-oil-pan-to-alternator.html

--------------
Why car leaks oil from oil filter?

http://schematicsdiagram.blogspot.in/2012/02/toyota-camry-leaks-oil-from-oil-filter.html

------------
Why engine is consuming lots of oil?

http://schematicsdiagram.blogspot.in/2012/02/2008-scion-xb-24l-engine-is-consuming.html

-----------
Maint REQD message on car dash?

http://schematicsdiagram.blogspot.in/2012/02/maint-reqd-message-on-2008-lexus-rx350.html

------
Remove Sump oil pan?

http://repairhelpcenter.blogspot.in/2012/03/remove-volkswagen-sump-oil-pan.html

--------
Sump not coming OFF?

http://repairhelpcenter.blogspot.in/2012/03/sump-not-coming-off.html

-----------
How to remove the sump on car? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-sump-on-vw-beetle.html

----------
Car oil sump removal diagram?

http://repairhelpcenter.blogspot.in/2012/03/volkswagen-beetle-oil-sump-removal.html

---------

This will help.

Thanks.


Posted on Mar 03, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a 96 camry and the oil dipstick tube has broken off how do I replace or repair the problem


Since the dipstick tube is a slide in fit, you will need to drop the oil pan to work the rest of the part out.
1) drain the oil
2) remove the bolts holding the oil pan (once they are all out, you might need to tap the pan to get it to release from the block-my brother's 97 camry was like this)
3) Remove the pan and look up for the dipstick tube end, spray it good with some WD-40, let it sit for a few minutes. The photo shows some pretty bad corrosion in your case.
4) with a set of channel lock pliers, begin to work the tube out. Take your time, you will be pushing out, not trying to pull the piece through.
5) once it is out, clean the edges of the dipstick tube opening.
6) Install new dipstick tube. ensure you have a good fit around the tube. otherwise, the crankcase pressure will squirt oil through.
7) Scrape off the old gasket from the oil pan and the face of the bottom of the engine.
8) lay the new gasket on the oil pan and begin to bolt it back on. Get the bolts in finger tight, then alternate torquing them down to ensure an even seal.
9) change oil filter and fill with new oil

Feb 07, 2014 | Cars & Trucks

1 Answer

1992 cadillac deville leaking oil at dipstick


I would look for other leaks. If you are sure it's leaking at the dipstick tube, there is normally an o-ring where the tube presses into the engine. In general, this is an odd place for a leak, as ther eshould be no oil pressure in the pan (where the tube terminates) and unless the engine is overfilled with oil, the tube end shouldn't be immersed in oil to leak. IF there is pressure in the oil pan, that generally indicates bad rings. I have seen engines where the oil dipstick actually pops out of the tube under pressure when the engine is running due to pressure in the oil pan from blow-by at the rings.

Jan 05, 2014 | 1992 Cadillac DeVille

2 Answers

Just wanted to know how to change transmission oil.


Hello,

Before You change the transmission oil, You need to check if it is due for changing. To check the transmission oil. please follow the steps below:
  1. Open the hood and locate the transmission dipstick. It is in front of the engine on the left side, just behind the radiator cap.
  2. Pull the ring on top of the dipstick to remove it from its tube. Wipe it off with the paper towel and replace it. This will ensure an accurate reading.
  3. Remove the dipstick again an look at the markings at the tip. If the fluid on the stick is below the full line, add more transmission fluid.
  4. Repeat this procedure until the fluid reaches the correct level on the dipstick.

There are different types of engine therefore there are several ways to change their transmission fluid. Unless you got something in there via dipstick its really not necessary to ever change the ATF. It's a messy job because there's no drain plug to change the fluid, but You can do it yourself if you're so inclined. To change the fluid,

  1. You have to get under your vehicle and remove the pan from the bottom of the transmission.
  2. When you loosen the pan, fluid will start to dribble out in all directions so you need a fairly large catch pan. You should also know that removing the pan doesn't drain all of the old fluid out of the transmission. Approximately a third of the old fluid will still be in the torque converter. There's no drain plug on the converter so you're really only doing a partial fluid change. Even so, a partial fluid change is better than no fluid change at all.
  3. A typical fluid change will require anywhere from 3 to 6 quarts of ATF depending on the application, a new filter and a pan gasket (or RTV sealer) for the transmission pan. The pan must be thoroughly cleaned prior to reinstallation. This includes wiping all fluid residue from the inside of the pan and scraping all traces of the old gasket from the pan's sealing surface. Don't forget to clean the mounting flange on the transmission, too.
  4. When the new filter is installed, be sure it is mounted in the exact same position as the original and that any O-rings or other gaskets have been properly positioned prior to tightening the bolts. Then tighten the bolts to the manufacturer's recommended specs.
  5. When refilling the transmission with fresh fluid, be careful not to allow any dirt or debris to enter the dipstick tube. Using a long-neck funnel with a built-in screen is recommended.
  6. Do not overfill the transmission. Too much fluid can cause the fluid to foam, which in turn can lead to erratic shifting, oil starvation and transmission damage. Too much fluid may also force ATF to leak past the transmission seals.
  7. Add half a quart at a time until the dipstick shows full. The transmission really isn't full yet because the dipstick should be checked when the fluid is hot, and the engine is idling with the gear selector in Park. So start the engine, drive the vehicle around the block, then recheck the fluid level while the engine is idling and add fluid as needed until the dipstick reads full.
Hope this helped. Thank You for using FixYa!!!

Jan 27, 2011 | Lexus IS Cars & Trucks

1 Answer

My 97dodge intrepid is leaking oil and i want to know where is the oil pan?


Hi. You might need to Replace the oil pan gasket is the oil is leaking. Here's the procedure on how to Replace the oil pan gasket.

1. Jack up the front end of the car and slide a jack stand under the vehicle. Make sure the jack stand is securely in place, and then put blocks in front of the rear wheels to keep them from rolling.

2. Slide under the car and put a drain pan under the drain plug of the oil pan. Loosen the drain plug with a socket wrench and allow all of the old oil to drain into the pan. Remove the old oil filter.

3. Disconnect the negative battery cable and remove the dipstick and its housing. Remove the collar on the rear of the oil pan. If the vehicle is equipped with engine oil cooler lines that lead to the oil pan, remove them as well, along with transmission oil cooler clips.

4. Remove the bolts holding the oil pan, and carefully remove the oil pan. Remove the old gasket. Scrape it with a putty knife if necessary, but be very careful not to scratch the surface.

5. Wipe out the oil pan with a clean cloth or paper towel, and wipe the joining surface of the oil pan with cleaning fluid or solvent. Apply a thin bead of automotive sealer and install the new gasket.

6. Replace the oil pan, tightening the bolts securely. Replace the transmission oil cooler clips, engine oil cooler lines, oil pan collar, dipstick housing and dipstick, and reconnect the negative battery cable. Install a new oil filter.

7. Take the car off the jack stand and fill the engine with the appropriate amount of SAE 10W-30 or SAE 5W-30.

All the best!

Nov 09, 2010 | 1997 Dodge Intrepid

2 Answers

My transmission leaks what should i replace


There are at least 5 places on the Automatic transmission that can over time, and mileage develope fluid leaks. Front converter seal at the front of the transmission,pan gasket in the center,dipstick tube o ring at the center on one side ,speed sensor o ring,and the tail shaft seal at the rear,of the transmission.
Place a flat piece or huge card board,under the engine and transmission,after driving you will see where the fluid,red in color is dripping. Its easier to spot exactly where the leak is comming if you can look under the car,while it is running, The easiest leak is the pan gasket,the dipstick tube, and the speed sensor,then the rear housing tail shaft bushing and seal.
If the front seal(converter seal) is leaking the transmission will need removed,and the seal,and maybe even the front pump bushing Replaced,it would be a good idea to replace the bushing esp if it has high mileage,80,000 or 100,000 miles of use.Change the fluid and the filter,while repareing the leak or leaks.Is a good idea.

Sep 17, 2010 | 1995 Chevrolet Camaro

1 Answer

Have a 1999 eclipse 2.0 L...Need to replace oil pan. Do I have to remove any other parts to get the pan off


2.0L Engine
  1. Disconnect the negative battery cable.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine undercover Front exhaust pipe Lower oil pan bolts and lower pan Cover Upper oil pan bolt and upper pan Baffle plate

    0996b43f8023193a.jpg Fig. Oil pan and related components-2.0L engine

To install:
  1. Clean all gasket surfaces of the cylinder block and the upper and lower oil pan.
  2. Install or connect the following:
    Baffle plate
  3. Apply a 0.16 in. (4mm) bead of sealant to the gasket surfaces of the upper oil pan.
    Upper oil pan onto the cylinder block within 15 minutes after applying sealant. Tighten the bolts as shown in the accompanying figure.

    0996b43f8023192d.jpg Fig. Upper oil pan bolt location and torque sequence-2.0L engine

  4. Apply 0.16 in. (4mm) bead of sealant to the gasket surfaces of the lower oil pan.
    Lower oil pan and tighten the bolts, in the sequence shown, to 88-106 inch lbs. (10-12 Nm)

    0996b43f8023192e.jpg Fig. Lower oil pan bolt tightening sequence-2.0L engine
    Front exhaust pipe Engine undercover Oil drain plug with a new gasket and tighten to 29 ft. lbs. (40 Nm)

    0996b43f8023192f.jpg Fig. Make sure to the install the new drain plug gasket as shown, or leaks will occur

  5. Lower the vehicle and fill the crankcase to the proper level with clean engine oil.
  6. Connect the negative battery cable. Start the engine and check for leaks.
Non-Turbo Engine
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Drain the engine oil into a suitable container.
  4. Once the oil has completely drained, install the plug and tighten to 25 ft. lbs. (34 Nm).
  5. Remove the front exhaust pipe.
  6. Remove the engine oil dipstick and tube assembly.
  7. Remove the front plate.
  8. Unfasten the oil pan mounting bolts, then remove the oil pan and gasket.

    0996b43f80222121.jpg Fig. Exploded view of the oil pan and related components-1999 2.0L non-turbo engine

To install:
  1. Apply sealant at the point where the engine block meets the oil pump.
  2. Use a new gasket and install the oil pan. Tighten the mounting bolts to 8.9 ft. lbs. (12 Nm).
  3. Install the front plate.
  4. Install the front exhaust pipe.
  5. Install the dipstick and tube assembly.
  6. Safely lower the vehicle to the floor.
  7. Refill the crankcase with oil to the proper level.
  8. nnect the negative battery cable.
  9. Start the engine and check for leaks.

Turbo Engine
  1. Disconnect the negative battery cable.
  2. Safely raise and support the vehicle.
  3. Remove the front exhaust pipe.
  4. Remove the exhaust pipe and muffler assembly.
  5. Drain the engine oil into a suitable container. Once the oil has drained completely, tighten the plug to 29 ft. lbs. (39 Nm).
  6. Remove the dipstick and tube.
  7. For AWD vehicles, remove the transfer case assembly as follows:
    1. With the propeller shaft still installed, remove the transfer mounting bolt.
    2. Insert a suitable prytool in between the transfer case and transaxle, then remove the transfer case from the center shaft.
    3. Remove the transfer case from the center shaft. Do NOT tilt the transfer assembly to the rear or oil will leak out.
    4. After removing the transfer assembly, insert tool MB991193 or equivalent, to prevent the oil from leaking out. Use a piece of wire to suspend the transfer case from the body.

      0996b43f80222122.jpg
      Fig. View of the transfer case with the tool installed to prevent oil from leaking out-1999 2.0L turbo engines
  8. Remove the bell housing cover.
  9. Disconnect the oil return pipe from the oil pan.
  10. Remove the oil pan mounting bolts. Tap the oil pan seal breaker MB998727 or equivalent between the oil pan and the engine block to break the seal and remove the oil pan.

    0996b43f80222123.jpg Fig. Exploded view of the oil pan and sealant application-1999 2.0L Turbo engine

To install:
  1. Clean the sealing surface on the oil pan and engine block. Apply a continuous bead of sealant MD970389 or equivalent to the oil pan.
  2. Clean the oil pan mounting bolt holes in the oil seal case.
  3. Install the oil pan to the engine block. Tighten the mounting bolts to 5.1 ft. lbs. (6.9 Nm).
  4. Use a new gasket and connect the oil return pipe to the oil pan.
  5. Install the bell housing cover.
  6. If equipped with AWD, install the transfer case assembly.
  7. Install the dipstick and tube assembly.
  8. Install the front exhaust pipe.
  9. Install the exhaust pipe and muffler.
  10. Install a new oil filter.
  11. Safely lower the vehicle to the floor and add five quarts of oil to the crankcase.
  12. Connect the negative battery cable.
  13. Start the engine and check for leaks.

Good luck (remember rated this help).

Mar 06, 2010 | 1999 Mitsubishi Eclipse

1 Answer

95 honda accord 2.2 vtec, oil is leaking out of the hole for the dipstick tube connecting to the engine, the o-ring is not keeping the seal, what can I do? When it was pulled out at first it looked like...


an oring, may work in the right place on the tube. at my shop, we either replace the grommet if it is accessable, or pull out the dipstick tube, put some rtv on it, and let it seal that way. it sometimes works with rtv, but not always, and you hva to be careful not to get it in the engine.

Feb 26, 2010 | 1995 Honda Accord

1 Answer

Leaking fluid


Only so many places these trans 41 TE can leak on the vans. Lines on top, speed sensors(input, output)one is below the lines the other is to right of the lines. Dipstick tube, trans solenoid gasket, Oil pan & extension gasket. Wipe off & clean area very well. Lines leaking, check clamps first before replacing. Speed sensor leaking replace o ring, Dipstick tube replace o ring, Trans solenoid replace gasket, Extension plate replace gasket If the pan is leaking you change the trans filter & put a gasket on the pan. The book says RTV on the pan, but FelPro make a gasket for the pan $6.99. Use a Chrysler trans filter!!!! O rings for sensors, tube around $3 each, trans solenoid gasket $3, extension gasket $10, Filter $11 + gasket $7 & 4qts trans fluid if doing the filter or extension gasket.

Jan 18, 2010 | 2000 Dodge Caravan

1 Answer

Do you have pictures of the parts that need to be removed in order to change the oil pan gasket?


Section 03-01: Engine, 4.6L (4V) 1997 Continental Workshop Manual IN-VEHICLE SERVICE Oil Pan/Oil Pump Screen Cover and Tube Removal
  1. Turn rear suspension leveler compressor switch (5K761) off (located in luggage compartment).
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove oil level dipstick (6750).
  1. Raise vehicle on hoist.
  1. Remove dual converter Y pipe (5F250). Refer to Section 09-00 .
  1. Drain engine oil from crankcase.
  1. Disconnect engine control sensor wiring (12A581) from the low oil level sensor connector.
  1. Remove the power steering pressure hose retainer brackets from the engine front cover studs (two places). Position the power steering pressure hose (3A719) out of the way.
  1. Remove 16 bolts retaining oil pan (6675) to cylinder blocks (6010) and remove oil pan and oil pan gasket (6710).
  1. Remove two bolts retaining oil pump screen cover and tube (6622) to oil pump (6600).
  1. Remove bolt retaining oil pump screen and cover and tube support brace to main bearing stud spacer.
  1. Remove oil pump screen cover and tube. Discard O-ring.

  2. 02d437f.gif

      Item Part Number Description 1 W701240 Bolt (16 Req'd) 2 6675 Oil Pan 3 6622 Oil Pump Screen Cover and Tube 4 6010 Cylinder Blocks 5 6710 Oil Pan Gasket A — Tighten to 20 Nm (14 Lb-Ft), then rotate 60 degrees clockwise
        Installation
        1. Inspect oil pump screen cover and tube and replace if necessary.
        1. Position oil pump screen cover and tube on oil pump with a new O-ring and hand-start two bolts.
        1. Install bolt retaining oil pump screen cover and tube to main bearing stud spacer finger-tight.
        1. Tighten oil pump screen cover and tube-to-oil pump bolts to 8-12 Nm (71-106 lb-in). Tighten oil pump screen cover and tube to main bearing stud spacer bolt to 20-30 Nm (15-22 lb-ft).
        1. Clean oil pan and inspect for damage.
        1. Clean sealing surfaces of engine front cover (6019) and cylinder blocks with a clean cloth. If scraping is required, only use plastic-tipped scrapers to prevent damaging the aluminum sealing surfaces.
        1. Position new oil pan gasket on oil pan.
        1. Apply Silicone Gasket and Sealant F6AZ-19562-AA or equivalent meeting Ford specification WSE-M4G323-A6 where engine front cover meets cylinder blocks and crankshaft rear oil seal retainer meets cylinder blocks. Position oil pan on cylinder blocks and install 16 bolts. Tighten bolts in sequence to 20 Nm (14 lb-ft), then rotate an additional 60 degrees clockwise.

      Apr 03, 2009 | 1997 Lincoln Continental

      Not finding what you are looking for?
      Cars & Trucks Logo

      495 people viewed this question

      Ask a Question

      Usually answered in minutes!

      Top Buick Experts

      yadayada
      yadayada

      Level 3 Expert

      75066 Answers

      Colin Stickland
      Colin Stickland

      Level 3 Expert

      22095 Answers

      Jeff Turcotte
      Jeff Turcotte

      Level 3 Expert

      7754 Answers

      Are you a Buick Expert? Answer questions, earn points and help others

      Answer questions

      Manuals & User Guides

      Loading...