Question about Cars & Trucks

Open Question

Fitting instructions for Brig-Ayd 75kg hoist

75kg Hoist

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

MrScary66613
  • 1990 Answers

SOURCE: hoist to lower spare tire does not work.

On my 95' Silverado I always had to get up under the Rear end and Kick the Spare to release it for Lowering. Give this a Try.

Posted on Jan 23, 2009

smartr10U
  • 1305 Answers

SOURCE: Replacing Chevy Trailblazer Spare tire mount/hoist.

Check out item 330335042615 on Ebay...
it''s the whole jack, handle etc... 50 bucks!
Tah dah!

Posted on Jun 09, 2009

SOURCE: ''2005 silverado stuck spare tire hoist''

How about a lot of rust under there?

Posted on Sep 30, 2009

  • 1 Answer

SOURCE: spare tire won't release.

This is the worst GM engineering i have ever seen !!!! The secondary locking mech. rust itself in the locked position on will NOT allow the tire to lower. After lowering the tire down approx. 2-4" the saftey lock is still engaged. I was able to reach above the tire and remove the bolt holding the hoist in place. {15 mm wrench}. Keep a floor jack under the tire to support it and as not to fall on your head. After removing the bolt the hoist is hooked on the frame member and must be lifted off to remove. Once you get it on the garage floor it is possible to disengage the locking mech. with a few tools and a big hammer. Good luck This should be a Recall

Posted on Nov 29, 2009

  • 1 Answer

SOURCE: 2004 gmc denali truck spare tire hoist does not

Verify that the plastic tub that the jack handle goes through is lined up correctly.

Posted on Dec 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2012 Mazda 2. Sitting on the road and turning the steering wheel 90 degrees right and left it makes a clunking noise. Put up on a hoist and doing the same it makes no noise. What is it.


the noise is generated by the weight on the points that are turning
the hoist you should be using is a 4 post hoist that the car drives on and the wheels are still on the hoist
any hoist that leaves the wheels dangling in the air will not be suitable to find the fault
most likely a steering ball joint end , suspension ball joint or failed suspension rubber mount

Mar 18, 2017 | Mazda Cars & Trucks

1 Answer

How do I replace the wire ( which has broken ) when you peg your clothes on the clothes line ?


hills used wire available from bunnings hardware or any hardware shop

May 18, 2016 | Cars & Trucks

1 Answer

How to take an motor out of an 1976 Minnie


You need to take off the bumper and the door that covers engine access. You'll need a low boy engine hoist. Take out the radiator and push aside the AC condenser and oil cooler. Take off the fan blades from the watre pump pulley. Find a good place to hook up the chain on the hoist. Now go under the engine and remove the access cover on the bell housing. Take out the bolts that hold the torque converter to the flywheel. Now go after the bolts that hold the transmission to the engine. Put a floor jack under the transmission so it wont drop when you jack up the engine with the hoist. After you remove all the electrical wiring from the components on the engine remove the bolts on the motor mounts and raise the engine with the hoist . Pull the engine out while looking for anything that you didn't disconnect. Be sure the transmission doesn't drop when the engine separates from it.

Sep 30, 2014 | Cars & Trucks

1 Answer

How to change starter motor


open the bonnet disconnect battery terminals.
then raise vehicle on hoist or car stands.
then disconnect the wiring that's connected to the starter motor.
once everything is disconnected remove the 2 bolts that secure the starter motor to vehicle.
when fitting new one just follow these steps in reverse..

Feb 05, 2013 | 1998 Holden VT Commodore

1 Answer

Wiring brig ayd hoist


Whats your problem? Can you explain it more precisely?


Performance Chip For Cars

Nov 07, 2012 | Cars & Trucks

1 Answer

The cable for the spare tire on my 2006 1500 works fine (it's all the way down) but the retainer did not lower at all so I cannot pick up the spare tire. Can anyone help? Thanks


  1. Rotate the hoist shaft counterclockwise until approximately 15 cm (6 in) of cable (1) is exposed.
  2. While holding the latch pin (3), fully depress the latch button (2) and release the secondary latch from the hoist assembly. Some side-to-side and/or up-and-down movement may be necessary to disengage the latch mechanism.
  3. Continue rotating the hoist shaft counterclockwise in order to lower the hoist the rest of the way.
  4. If this does not release the secondary latch, the spare tire hoist will need to be replaced. See the following procedure.
Important: If the spare tire hoist has been fully raised without a spare tire in place, the secondary latch mechanism may have become engaged. If this has occurred the hoist will not lower and the following steps will need to be followed:

Nov 01, 2009 | 2005 Chevrolet Silverado

3 Answers

Spare tire won't release.


This is the worst GM engineering i have ever seen !!!! The secondary locking mech. rust itself in the locked position on will NOT allow the tire to lower. After lowering the tire down approx. 2-4" the saftey lock is still engaged. I was able to reach above the tire and remove the bolt holding the hoist in place. {15 mm wrench}. Keep a floor jack under the tire to support it and as not to fall on your head. After removing the bolt the hoist is hooked on the frame member and must be lifted off to remove. Once you get it on the garage floor it is possible to disengage the locking mech. with a few tools and a big hammer. Good luck This should be a Recall

May 20, 2009 | 2005 Chevrolet Silverado

1 Answer

Tire hoist will not lift back up.


no the hoist must be replaced, they are famous for this, all trucks use the same one.

May 12, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

Fitting a clutch to mazda mx6


It's easier to remove the engine but if you have a hoist and good gears you might get away without removeing the whole engine.

Mar 22, 2009 | 1993 Mazda MX-6

1 Answer

Clutch replacement details for 1996 legacy GTB


Trust me it is quite an excercise and not worth doing yourself. With the proper tools, a hoist and a my mate who is a Guru Subaru Mech it took 4 hours. Without having done it before and without the Hoist ( which is wha I was going to do initially ) I'd say you wouldn't get much change out of 8 - 12 hours.

Dec 22, 2008 | 1996 Subaru Legacy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...