Question about 2006 Toyota Hilux 3.0

1 Answer

Toyota hilux 3.0 D4D hard starting showing crankshaft position sensor circuit malfunction code P0335.how do i solve this...?

Posted by on

  • saayeng bonny Dec 01, 2012

    Have an accident d4d 2kd ftv involved in an acciddent but would not start after that. craks well but would not start what could be the problem?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 5,763 Answers

Check the connection to crank sensor, if wiring is good and connection is clean then replace the crank sensor and reset the code, this is the first step, the computer could be a problem also but most times its the crankshaft sensor. good day

Posted on Feb 22, 2012

Testimonial: "The connections to the sensor were bad and the hard starting is gone.Thanks JB"

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3600 Answers

SOURCE: Put a motor in my '97 toyota camry LE 2.2 4cyl.

02 sensor is defective... if the cam sensor did not work it would not run, try replaceing the 02 SENSOR...

Posted on Jun 16, 2009

  • 7353 Answers

SOURCE: have p0130 and p0133 codes 98 toyota tacoma

I would check the O2 sensor, and if it checks bad, replace it, and clear the trouble codes. If the light comes back on, you may need to check further. .

Posted on Oct 28, 2009

mrgreenz
  • 962 Answers

SOURCE: where is the crankshaft position sensor; how to replace

Both are located under the timing cover.you will have to remove the timing sproket to get to the CrankshaftPS. be careful to notice how you removed it. the sproket have to be reinstalled exactly the same way you removed it.

Posted on Dec 19, 2008

  • 215 Answers

SOURCE: Have 1999 Toyota Solara SLE

the part is located on top of the egr valve and has a electrical plug going to it........i would replace yhe egr valve assembly that has the sensor and the valve all in one due to age of the car and the mileage in case the egr valve is sticking and is holding the sensor open or is not letting it close all the way.......i hope this info will help you and if i can be in any further help let me know......let me and fixya know if i was ant help to you and a thumbs up would be greatly appreciated..........thanks and have a good day........

Posted on Jun 22, 2011

  • 277 Answers

SOURCE: Toyota diesel hilux D4D noisy engine.just

Take the Vehicle back to the Installer/Supplier, for a Free of Charge CHECK and ADVISE under New Engine Warranty. If the OIL PRESSURE is LOW, when starting up from COLD, there is a genuine fault, so do not drive any distance.
Regards,DT

Posted on Aug 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crank and cam sensor replaced . cars starts and run but still reads code 335 . cranksensor circuit malfunction. and idea whats the issue why this code is still coming up.?


the sensor may be good its the circuit code which means can be a wiring /connection problem not just the sensor the following link is courtesy of obd-codes.comP0335 - Crankshaft Position Sensor A Circuit Malfunction OBD-II Trouble Code Technical Description Crankshaft Position Sensor A Circuit Malfunction What does that mean? The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set. Symptoms NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include: Vehicle may not start (see above) Vehicle may run rough or misfire MIL illumination Causes A P0335 "check engine light" code could be caused by: Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Broken timing belt Failed PCM Possible Solutions Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs? If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay? If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault. This code is basically identical to P0385. This code P0335 refers to Crankshaft Posistion Sensor "A", whereas P0385 refers to Crankshaft Position Sensor "B". Other crank sensor codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.

Read more at: http://www.obd-codes.com/p0335
Copyright OBD-Codes.com
http://www.obd-codes.com/p0335

Aug 19, 2015 | 2005 Chevrolet Impala

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

I am workimg on my 2000 nissan quest. it cranks and turns over but will not start. it is throwing codes P0340 twice and P0325. we replaced the distributor cap and rotor and still nothing. probably goi


P0325 Knock Sensor 1 Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329 Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330 Knock Sensor 2 Circuit (Bank 2) -Circuit Malfunction
P0331 Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332 Knock Sensor 2 Circuit Low Input (Bank 2)
P0333 Knock Sensor 2 Circuit High Input (Bank 2)
P0334 Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335 Crankshaft Position Sensor -Circuit Malfunction
P0336 Crankshaft Position Sensor -Range/Performance
P0337 Crankshaft Position Sensor -Low Input
P0338 Crankshaft Position Sensor -High Input
P0339 Crankshaft Position Sensor -Intermittent
P0340 Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
sorry would a play with this to know for sure ,check the wiring plugs onto the sensors to make sure their not full of oil or corroded

Aug 07, 2014 | 2000 Nissan Quest

1 Answer

2003 Toyota Camry 2.4 ticking noise & code set up P0335


P0335: Crankshaft Position Sensor Circuit Malfunction

Jan 04, 2013 | Cars & Trucks

1 Answer

Engine management light on trouble code P0335


P0335 - Crankshaft Position Sensor 'A' Circuit Malfunction

Possible causes- Faulty crankshaft position sensor (most common)
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery causing slow engine crank over.

Oct 25, 2012 | 2005 Fiat Punto

1 Answer

2001 Oldsmobile Aurora Codes P0302, P0335, P385, P0386


p0302 Misfire cylinder two

p0335 CKP Sensor 'A' Circuit Malfunction

p0385 Crankshaft Position (CKP) Sensor B Circuit

p0386 Crankshaft Position Sensor B Circuit Range/Performance

Make sure your crankshaft sensor is plugged in or replace the sensor if the plug is good.

Jun 05, 2011 | 2001 Oldsmobile Aurora

1 Answer

I have a codes P0073 P0339 and P0335 what a re each of them?


CODE POO73- OUT SIDE AIR TEMPERATURE SENSOR CODE PO339- CRANKSHAFT POSITION SENSOR CIRCUIT INTERMITTENT. CODE PO335 -CRANKSHAFT POSITION SENSOR CIRCUIT MALFUNCTION.

Jul 07, 2010 | Cars & Trucks

Not finding what you are looking for?
2006 Toyota Hilux 3.0 Logo

2,151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...