Question about 1995 Honda Accord

1 Answer

How do i bleed the master clutch cylinder with it on the car

Pedal is sticking replaced the old one need to know how to bleed the master clutch cylinder to fix my pedal

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 93 Answers

This sort of problem usually happens when the cups are worn in either the master cylinder or slave cylinder.They should both be replaced at the same time war repaired at the same time.To bleed the system he needs somebody inside the car to pump the pedal unless you have a pressure bleeder.What needs to happen is that somebody pumps the pedal to build up pressure and while they hold the pedal ******* the floor someone needs to open the bleed screw on the slave cylinder.This process needs to be repeated until you finally get positive pedal feel. You may have to repeat this process up to 10 times unless of course you have a pressure bled.It is possible to believe the system without a pressure bleeder, it just takes a little longer.If you do not understand what I mean by pressure bleeder, it is a device that fits into a 5 gallon drum of brake fluid and forces the fluid enter the master cylinder wire photos and a special cap that goes on the master cylinder, sealing it from any outward for inward leaks. They tend to be fairly expensive.I hope this helpsregards

Posted on Feb 22, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: clutch pedal stays down

Still have air in system.. Try this: Pull pedal up,fill reservoir to the top, open bleed nipple on slave cyl all the way,leave for a while to "gravity feed" keeping the reservoir full,& an eye on the nipple, until all bubbles are expelled and clean brakefluid drips out(could take a few minutes). Close the nipple, and bleed system as usual....

Posted on Jun 24, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

  • 1 Answer

SOURCE: 1995 honda civic clutch

we had the same problem with our 96, come to find out someone had installed an after market securtity, we found the switch under the hood release it was very small but that did the trick, just look for something that looks like it doesnt belong

Posted on Jan 28, 2009

localwonder
  • 6784 Answers

SOURCE: Clutch has no resistance, stays near floor after applying pressur

You could refill but, i would replace the clutch master cylinder and slave cylinder as well. these two parts are failing.

Posted on Mar 06, 2009

Keith100881
  • 74 Answers

SOURCE: put in new clutch and slave cylinder. no clutch pedal. how do you bleed the cylinder?

work it back and forth with your hand and you will get pedal after a while then bleed like you would brakes get help so one can pump and the other can bleed

Posted on May 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Honda EX clutch. It does not ingage. It pops to the top or sticks to the floor


Not sure of the model EX, but it probably has a clutch hydraulic slave and master cylinder that has leaked out the hydraulic fluid. Fill the clutch master cylinder (near the brake master cylinder) with brake fluid and pump the clutch pedal several times. The clutch work again until the fluid leaks out, so the permanent fix is to replace the master and or slave cylinders and bleed the system. Other models have a clutch cable that would need replacing in this case

Oct 24, 2017 | Honda Cars & Trucks

2 Answers

How do I bleed a clutch for a 1985 mazda rx-7


Your clutch slave cylinder could be bad and leaking,here's a picture of it,it's bolted to the side of transmission,has a bleeder screw on it for bleeding.Normally,your fluid shouldn't be low,here's how to replace.

Jan 30, 2013 | 1985 Mazda RX-7

4 Answers

My clutch pedal is sticking to the floor?


Hi replace the clutch cylender

Nov 22, 2017 | Cars & Trucks

1 Answer

Clutch pedal is sticking


ok
if it just sticks without any strange sound or lack in power then you just need a new pedal wire or a master cylinder of the clutch pedal i don`t know that kind of cars but its old and probably will using just typical wire just review the fluid reservoir of the clutch master for any lack of fluid or sweating

May 31, 2011 | 1994 Plymouth Colt

2 Answers

My clutch doesn't always disengage when the peddle is on the floor and when starting out in first bolts ahead as though the clutch was already part way out. I took it to a shop and they said my clutch...


your clutch master cylinder is right beside your brake master cylinder. I would advise you to replace the master cylinder and the slave cylinder together. The slave cylinder is on the side of the transmission. The slave cylinder does have a bleeder screw on it after the parts are bolted in place fill with dot 3 brake fluid and open the bleeder on the slave cylinder until fluid starts dripping out. Then tighten bleeder then open bleeder and have someone push down on clutch pedal while the pedal is pushed down tighten the bleeder the release pedal. Repeat this procedure until you get no air and the pedal feels normal and you should be good to go. Good luck!

Apr 14, 2011 | 1991 Toyota Celica

2 Answers

My 1996 Chevrolet K3500 Dually has a hydraulic clutch, how do I change the fluid and bleed it.


FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Jan 22, 2011 | 1996 Chevrolet C/K 3500

1 Answer

Started off with cluth sticking to floor.would have to pull clutch pedal back up with foot. truck would stick in gear. even with clutch fully depressed. seemed like spring had disconnected from clutch...


your clutch uses a hydraulic master and slave cylinder to disengage. It is likely that the slave has been leaking and the reservoir gone dry, thus allowing air into the system and reducing effectiveness. Check the clutch master cylinder reservoir (near the brake reservoir) fluid level. If low, also check the slave cylinder at the clutch for leakage. If leaking, replace the slave and bleed the system. If you need procedures or have more questions, please let us know.

Sep 25, 2010 | 1994 Nissan Pickup

2 Answers

Clutch pedal going to the floor too easily..


You likely have a leak in either the master for the clutch, the line going to the slave unit or the slave itself. You need to look at these items and replace any leaking components. If the master is full, likely it is internally bypassing and therefore needs replacement. Air in the system can only get in there from a leak. bleeding may make it work for a short time but is not a cure. After making any repairs you do need to bleed it though. (just like brakes)

Oct 23, 2009 | 2004 Nissan Maxima

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

Not finding what you are looking for?
1995 Honda Accord Logo

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...