Question about 2002 Mazda Protege

Open Question

What should a tune up cost for a 2002 mazda protege 5

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Blown main fuse on 2003 mazda protege 5.

There are two bolts on the side of the fuse itself. Under the fuse box on each side. Unbolt those and it will come out.

Posted on Dec 23, 2008

Ad
  • 1 Answer

SOURCE: How much should I reasonably

replacement of timing belt $350-$500. aftermarket shops will try to sell you a package containg a belt, water pump, and tensioner pulley. the dealer will just replace the belt, they might recommend to replace the water pump if there are alot of miles on the car, they will also inspect the pulley for wear.

Posted on Jan 09, 2009

  • 840 Answers

SOURCE: 2002 Mazda Protege horn location

Their are usually in back of grille or on the underside of rails. you will need to take off the front bumper to get access.

Posted on Jan 24, 2009

  • 2 Answers

SOURCE: where is the blower motor resistor on a 2002 mazda protege?

just remove the glove box and its right behind it just take the white pug out and the two phillips screws to remove the resistor out, replace with the new one and cool off!!!! Hope this helps

Posted on Aug 04, 2009

  • 32 Answers

SOURCE: obd2 code p0300 on mazda protege 2002

Just had one of these with a maxima, the code is multiple random misfire, when a misfire occurs, to start is do the basics, replace the plugs, check fuel pressure, clean throttle body, and coolant is topped up. also I have seen if the O2 sensor is not working correctly is can cause a misfire, you will need a scan tool to look at what the O2 sensor is doing, o rby back probing the sensor (don't damage the O2 sensor wires). If it wires replace them as well, if it has coils they usually dont give that code if one fails, it will pinpoint that a certain coil if one fals.

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Window wont go up


Power window repair - Mazdas247




www.mazdas247.com > ... > Mazda Protege Forum > Protege How-To

Aug 8, 2005 - 10 posts - ‎10 authors

I have a 2002 and last week the driver's side power window died a horrible death. ... Check out my mods -> 2001 Mazda Protege LX aka Rum Runner ... My front pass sidewindow won't go up or down anymore. haven't taken ...


Passenger Window on 2007 CX-7 will not come up ...

2 posts

Nov 28, 2012


Driver's side window auto-up/down issues - Mazdas247

15 posts

Jun 10, 2011


Power Window Problem - Mazdas247

7 posts

Aug 9, 2009


Driver Side window controller won't work

14 posts

Nov 11, 2006


More results from www.mazdas247.com




2003 Mazda Protege 5 Replacing The Power Window Motor ...





? 7:02


https://www.youtube.com/watch?v=N3GP2UwTtAQ

Feb 3, 2015 - Uploaded by Steve K.

2003 Mazda Protege 5 Replacing The Power Window Motor and Regulator. Steve K. ... Looks like you just ...





Amazon.com: Dorman 741-741 Mazda Protege Fr


Oct 30, 2015 | 2002 Mazda Protege

1 Answer

Where is the EGR valve on a mazda protege 5


I own a 2002 Mazda Protege5 with the FS2.0 Motor. The EGR Valve is located below the throttle-body. You must take off the Intake tube to get a good view of it. To replace it I think you might have to take off the throttle-body, but I'm not sure about that...(yet)


NOTE: Mazda put out a technical note stating that "if your car has sat for a long time, the egr valve could be damaged by moisture (rain) and will need to be replaced". My 2002 Protege sat for 3 weeks and the rain caused this exact issue and had to be replaced. How did I know? The engine light came on (after never coming on) and the car had an extremely rough idle. Total cost was ~$400 (ouch).

Oct 13, 2011 | Cars & Trucks

1 Answer

The check engine light is flashing in my 2002 mazda protege 5. what does this mean?


This means an error has been detected by your engine management system. The next step is to pull the error codes from the computer and investigate those indications.

Jul 26, 2010 | 2002 Mazda Protege

1 Answer

I have a mazda protege 5 and the o/d on/off light continues to stay on? How do I fix this and how much is it going to cost


The first thing I would check is the Pushbutton on your shifter. You can grab it with your fingers usually and wiggle it out. If you remove wires and OD light goes out, you can get new or used switch and easily replace it.

May 04, 2010 | 2002 Mazda Protege

1 Answer

Manual transmission capacity of 2002 5 spd 2.0l engine mazda protege lx


about 2 quarts and then top off to just below the lip of the fill plug on the side of the trans

Sep 04, 2009 | 2002 Mazda Protege

1 Answer

Timing Belt replacement- two recomendations by mazda manual


they are good for well over 100k. If your engine is freewheeling (that is - if belt does break, no valve will hit the psiton), I would just keep driving it until it breaks or never does.
I am driving my 93 Villager until it breaks. over 150k right now, freewheeling engine.

As for cost, about $400 is my guess.

Ask your dealer service dept if it's freewheeling. check your owner manual too.

May 27, 2009 | 2002 Mazda Protege

1 Answer

How to replace knock senor switch on 2002 mazda protege 5



Removal & Installation

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa95.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Knock sensor removal and installation-Mazda 3

  1. Disconnect the negative battery cable.
  2. Remove the intake manifold bracket.
  3. Disconnect the sensor connector.
  4. Remove the sensor from the engine block using special tool 49H018001 or equivalent.
  5. Installation is the reverse of the removal procedure.

    0900c1528019fa96.jpg enlarge_icon.gifenlarge_tooltip.gif GL G

May 09, 2009 | 2002 Mazda Protege

1 Answer

How to replace the serpentine belt of protege 5 2002, also need the routing diagram


Posted by Asker under 1997 Mazda Protege for their 2002 Mazda Protege 5.
Both are included Below

Click on the following free direct Link. It has the Belt Diagrams for the 1997 Mazda Protege with either the 1.5L DOHC In-Line 4-Cylinder or 1.8L DOHC In-Line 4-Cylinder Engines; along with various engine options (AC/No AC, etc.). Included are Instrucional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/1997/make/mazda/model/protege/1997_mazda_protege_drive_belt_routing_diagram.htm

Click on the following free direct Link. It has the Belt Diagrams for your 2002 Mazda Protege 5 2.0L DOHC In-Line 4-Cylinder Engine; along with various engine options (AC/No AC, etc.). Included are Instructional Diagrams for loosening (for removal) and tightening (for replacement) using the Adjustment and Locking Bolts/Nuts.
http://www.2carpros.com/car_repair_information/year/2002/make/mazda/model/protege5/2002_mazda_protege5_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 13, 2009 | 1997 Mazda Protege

1 Answer

Blue Smoke on starting, and also straining uphill Mazda Protege


The problems with the exhaust valve and the failed piston are probably due to that cylinder running lean. Check the fuel injector for that cylinder and also look for vacuum leaks that would affect that cylinder. We do not think the wrong heat range of spark plugs would cause the problem you describe.

Jun 20, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
2002 Mazda Protege Logo

Related Topics:

368 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...