Question about 2011 GMC Terrain SLE2

Open Question

Location of my evap. canister for my 2011 terrain

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
GM Elec
  • 1000 Answers

SOURCE: looking for the location of my evap. canister for

The canister is located around the fuel tank. Typically above the rear axel.
Good luck.
Regards,

Posted on Sep 08, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of 2012 GMC Terrain canister purge valve, part PV479


watch this video and it may answer your question 2011 GMC Acadia Canister Purge Valve location it should be what you are looking for.

Apr 18, 2017 | GMC Cars & Trucks

1 Answer

How can I replace the evap canister in 2011 Kia Sedona?


How do you know the canister is bad?? There should be no issue with it being a 2011 unless you ran over something and damaged it. There are many things other than the canister that will cause evap leaks/codes. What code led you to the canister replacement idea?

Aug 23, 2015 | 2011 Kia Sedona

1 Answer

Where is my vent valve solenoid on my 2006 Chevy Colbalt?


It's located under the vehicle back behind the fuel tank , Installed in the canister ! Remove the EVAP canister vent solenoid valve from the canister !
Rotate the EVAP canister vent solenoid valve counterclockwise in order to release it from the locked position.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister harness electrical connector (2) from the EVAP vent solenoid valve. Clean away any debris that may be present around the EVAP canister vent solenoid valve.
Remove the EVAP canister bolt. Lower the EVAP canister.

Feb 25, 2015 | Chevrolet Chevy Cars & Trucks

1 Answer

Evap canister


The canister is located in a frame behind the left rear wheel, and you will need wrenches, a socket set, and a jack to raise the back of the truck. Carefully remove the hoses from the canister - if you damage the quick connects, you will have a big problem. Then remove the canister frame by removing the bolts holding it (remove the screws holding the left rear plastic wheel well to get access to the front of the canister frame). Remove the old canister from the frame, attach the new canister, and then reinstall the frame.
If you are having a problem with the EVAP system, you should also check the hoses and replace the EVAP purge valve and the EVAP solenoid valve ( typical failure points on these vehicles - if you have a problem with one component, the rest will follow shortly after). The purge valve is located on the bottom of the vehicle near the center of the rear axle (just follow the small purge hose attached to the canister). The vent valve is located on the top right side on the engine. All parts are available from Amazon or a GM dealer.

Apr 09, 2014 | 1999 GMC Jimmy

1 Answer

Location evap canister


Are you sure you need to replace the canister and vent control valve? Do you have specific trouble code? Trouble codes associated with those components are sometimes jut due to loose connections/fittings or cracked tubes. Jack up the car and make a thorough inspection of tubings and fittings. If you have to disconnect tubings, make sure you mark them as it can get complicated if you make a mistake.

Oct 26, 2013 | 2011 Nissan Juke

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

1 Answer

Need to know where to find the canister purge valve


For the location of canister purge valve,check the following help links mentioned below:--
Click the link :---

Location for EVAP Purge Valve Solenoid?

http://schematicsdiagram.blogspot.in/2012/06/2002-nissandatsun-pathfinder-location.html


------------------

How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html

-------------

2004 Chrysler PT Cruiser: Location of EVAP Purge Solenoid Valve?

http://schematicsdiagram.blogspot.in/2012/06/2004chrysler-pt-cruiser-location-of.html

-----------
These will help.
Thanks.

Jan 08, 2013 | Cars & Trucks

1 Answer

Vent control valve system contaminated recommended flush, replace canister & install filter kit...cost app $900.00...is this necessary, can i do it myself???


Yes you can do this job.Just get the evap vent valve replaced.
It is not under the hood but is under the car.

Replacing the canister and valve is simple, just disconnect hoses, remove bolts and reconnect. Just make sure to mark all the hoses before disconnecting, and that the valve "O" ring is in place.
It is located over the spare tire. The reason for the replacement of the canister is that the valve is bolted to the canister and the bolts will break off also sometimes with the corrosion on the bolts causes swelling and cracks the canister. ---------- click this link below for more help:--- http://technoanswers.blogspot.com/2011/06/how-to-replace-evap-vent-control-valve.html ------------ This should help.Thanks.Helpmech.

Jun 07, 2011 | 2006 Nissan Frontier

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

Not finding what you are looking for?
2011 GMC Terrain SLE2 Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...