Question about Cars & Trucks

Open Question

What color wire is for the reverse lights on a 2007 sterling lt9500

Reverse lights dont work

Posted by Anonymous on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 513 Answers

SOURCE: location of brake light switch for 2007 sterling

should be on brake pedal next to the rod going to master cylinder

Posted on Jan 16, 2010

  • 3 Answers

SOURCE: location of brake light switch for 2007 sterling

Dash board just below cluster on l.h. side, air operated switch.

Posted on Oct 10, 2012

  • 1 Answer

SOURCE: location of brake light switch for 2007 sterling

Have torn apart whole dash and followed every air line still can not find brake switch

Posted on Sep 08, 2016

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why will the engine brake not work in my sterling 2008 lt9500 prime mover could it be a fuse and where are they located

Assume by engine brake you mean an exhaust brake?

Exhaust, eddy current or transmission brakes are usually fitted to vehicles to help them cope with very hilly or mountainous country, extend the life of standard braking components and to reduce driver fatigue.

When an exhaust brake is engaged a butterfly valve in the exhaust is closed via a servo and a linkage. The servo could be vacuum, air pressure or electrical.
I only have experience of the air pressure operated type but I suggest before you begin looking at fuses and other electrical problems you ensure the butterfly valve is not seized or semi-seized and the linkage is secure.

Jun 30, 2016 | Sterling Cars & Trucks

1 Answer


You can ground the wire to any unpainted metal surface. Find a screw or bolt, loosen it, put the wire under it and re-tighten.

Apr 29, 2012 | Cars & Trucks

1 Answer

When you push the the stop pedal and release that, the stop light dont off

is this a rover sterling 827 if so adjust the stop light switch

Jul 02, 2011 | 2007 Sterling 827

1 Answer

Only one reverse light goes on on my 2007 VW Passet, how do I fix?

if you have already tried changing the bulb and still not working than the simplest way is to run a wire from the working bulb to the other side saves time trying to unravel all the harness's first you will need to find wich of the two wires is not doing its job the power wire or the ground wire? test light will help you with that, with engine off put your car in reverse turn the ignition to on that will turn on the working reverse light use a test light to find the problem go to the none working light remove the bulb using the test light touch each connection point to see if any light up the test light if not then you have a bad power supply, but if it does light up then you have a bad ground wire in either case you can jump the working light to fix the light if ground is bad jump the ground and vise versa.......

Nov 14, 2010 | 2007 Volkswagen Passat Sedan

3 Answers

Location of brake light switch for 2007 sterling lt9500

should be on brake pedal next to the rod going to master cylinder

Jan 16, 2010 | 2007 Sterling 827

1 Answer

My revirse lights do not work

Really dont need to know color of wire for this system is simple. On the switch (left rear corner on transmission) there are three wires. one wire is power, one allows it to start in park or neutral and the other is for the reverse lights. If I remember correctly the two outer terminals operate the reverse lights. Find the power lead and jump to each of the other two to determine which is for the reverse lights. Likely you will find that the switch is bad and there is no wiring problem. Make sure that reverse lights have good grounds as well.

Aug 16, 2009 | 1987 Dodge Ram Wagon B250

1 Answer

2007 ford e350 van, reverse lights wont work

On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

Apr 10, 2009 | 2007 Ford E-150 XLT Wagon

1 Answer

Reverse lights dont work

follow the wire from the reverse lite and it should lead to the transmission somewhere along that wire you will most likely find that the wire is broken or corroded off. also check the groung wire that it is grounded properly in the reerse lite itself.

Oct 16, 2008 | 1995 Chevrolet Cavalier

1 Answer

Back up lights

hot in run fuse # 15 then it goes to the automatic or standard switch then its goes to the reverse lamps. its pink from the fuse to the switch then its light green to the lamps. make sure you have a good ground........ good luck jimmy

Sep 25, 2008 | 1995 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13632 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides