Question about 2000 GMC Yukon Denali

Open Question

How to change a thermostat in a 2000 gmc yukon

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dgjtex
  • 405 Answers

SOURCE: Where is the windshield washer pump on a 2000 GMC Yukon XL?

left fender on the washer fluid bottle.

Posted on Dec 29, 2008

  • 1596 Answers

SOURCE: Oil Pan Gasket Replacement - How to - GMC Yukon 2000








Removal Procedure

Important: The original oil pan gasket is retained and aligned to the oil pan by rivets. When installing a new gasket, it is not necessary to install new rivets.
DO NOT reuse the oil pan gasket. When installing the oil pan, install a NEW oil pan gasket.

Caution: Refer to Battery Disconnect Caution in Service Precautions.

  • Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure
  • Remove the front differential if equipped with four wheel drive. Refer to Differential Carrier Assembly Replacement in Front Axle.
  • Remove the under body shield from the vehicle
  • Remove the oil pan underbody shield.
  • Remove the cross brace if equipped.
  • Drain the engine oil and remove the engine oil filter. Refer to Engine Oil and Oil Filter Change
  • Remove the lower transmission-to-oil pan bolts
  • Disconnect the oil level sensor electrical connector.
  • Remove two front wiring harness retainer bolts.


10. Remove the engine wiring harness retainer bolts from the engine oil pan.
11. Remove the engine oil cooler pipe to oil pan bolt.
12. Remove the transmission oil cooler pipe retainer and the bolt from the oil pan.
13. Remove the starter motor. Refer to Starter Motor Replacement.
14. Remove the left closeout cover and bolt.
15. Remove the engine oil pan. Refer to Oil Pan Removal.

Installation Procedure

Important: The alignment of the structural oil pan is critical. The rear bolt hole locations of the oil pan provide mounting points for the transmission bellhousing. To ensure the rigidity of the powertrain and correct transmission alignment, it is important that the rear of the block and the rear of the oil pan must NEVER protrude beyond the engine block and transmission bellhousing plane.

Will Send Remainder in another this place dont take kindly to larg files Your Email Address would realy be Better Then I could send Pictures Also up to YOU

Posted on Jan 27, 2009

dennymulford
  • 1055 Answers

SOURCE: my heat does not work in my 2000 yukon xl. I have

bad control valve or plugged heater core

Posted on Dec 31, 2009

duane_wong
  • 6826 Answers

SOURCE: i want to get a tune-up on my 2000 GMC Yukon xl

Spark plugs, wires, and air filter usually will maintain the vehicle.

Posted on Feb 05, 2011

tginks
  • 67 Answers

SOURCE: how to reset service lamp after oil change on a

I have a 2005 GMC Envoy and you turn the key to on, then press the gas pedal to the floor three time in 5 sec. The oil light blinks once and your done. I'd give it a try. Remember engine off but the key is on. Can't hurt to try it. Otherwise you'll need an owners manual to figure it out.

Posted on Feb 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tools do i need to change brake pads on 2005 yukon xl


Jack, wheel wrench, socket set, large screw driver, pair of pliers or grips. Lithium grease for the pins. Watch all of these videos. .spell{font-size:18px}.spell_orig{font-size:15px}#mss p{margin:0;padding-top:5px}




g-img{display:block}._WCg{display:block;border:0;position:relative} Search Results

    How To Install Replace Front Brake Pads 2000-06 Chevy ...

    9k=? 4:46 https://www.youtube.com/watch?v=nPohZtD8zlA May 27, 2014 - Uploaded by 1A Auto Parts http://www.1aauto.com/brake-pads/i/1abps00080 1A Auto shows you how to ... Front Brake Pads 2000-06 ...

    HOW TO INSTALL REPLACE GMC YUKON DENALI ...

    z? 14:10 https://www.youtube.com/watch?v=um7dt_yvZ1s Sep 20, 2012 - Uploaded by TheRykerDane Video on how to change the brake pads and rotors on a 2004 GMC Yukon Denali. Changing these parts ...

    How to REPLACE INSTALL BRAKES and ROTORS GMC ...

    2q==? 11:32 https://www.youtube.com/watch?v=UWqows3P4DE Feb 11, 2012 - Uploaded by TheRykerDane Video on how to change the brake pads and rotors on a 2004 GMC Yukon. Changing these parts ... Would ...

    GMC Denali Brake Pads Removal and Installation - YouTube

    z? 3:45 https://www.youtube.com/watch?v=uEKs8nphVxU Oct 24, 2012 - Uploaded by AnotherLookFilms Remove and Install rear brake pads on your 2006 GMC Denali XL. ... 9-21-13 2007 GMC Yukon rear brakes ...

    GMC Yukon Denali Front Disc Brake Pad Replacement ...

    2q==? 8:21 https://www.youtube.com/watch?v=w_gn_l5lYkw Jun 20, 2013 - Uploaded by AMS Automotive Watch the proper procedure for replacing front disc brake pads. Featured vehicle: 2007 GMC Yukon Denali ...





Jan 22, 2016 | Cars & Trucks

1 Answer

How do i change the thermostat on a 2004 GMC Yukon 5.3 liter?


follow the top rad hose at the end where it conects to the moter is a sleve held on by two bolts the thermostat is in there

Nov 25, 2012 | 2004 GMC Yukon

1 Answer

How do you find and fill the radiator in 2003 GMC Yukon XL


Some of these vehicles have a false petcock. Pop off the lower hose over a catch pan, pour a gallon of water in the plastic Dexcool Coolant bottle and put the hose back on when it stops pouring out. Fill to the max line and run the car until both radiator hoses are hot (thermostat has opened). Replenish fluid to max line and cap the bottle. If you have electric fans make sure they come on and make sure your temp. gauge stays in the middle. It'll take longer on cooler days. You might have to get in the car and gas it to about 2000 rpms. Don't cap the bottle until the thermostat opens. If it vomits, change the thermostat and again make sure the electric fans kick on or the clutch fan speeds up at about 210 degrees.

Sep 04, 2010 | 2003 GMC Yukon XL

1 Answer

What size engine does my 2000 yukon xl have is a 4x4


2000 GMC Yukon XL 1500 4WD:
Available engines: 8 Cylinders T 5.3L SFI

2000 GMC Yukon XL 2500 4WD:
Available engines: 8 Cylinders U 6.0L SFI

Hope this help (remember comment and rated this).

Apr 23, 2010 | 2000 GMC Yukon XL

1 Answer

My heat does not work in my 2000 yukon xl. I have


bad control valve or plugged heater core

Dec 31, 2009 | 1999 GMC Jimmy

1 Answer

2001 yukon denali thermostat issue?


the rad is full and no vissible coolant leaks the next check woud be the fan clutch on the water pump if it spins freely when you turn off engine (hot) change it,you need specisl tools to remove

Jun 21, 2009 | 2000 GMC Yukon Denali

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...