Question about Chevrolet Blazer

1 Answer

It wont move when i put it in drive or third but it will manually in first and second i just rebuilt it myself and im not really sure if i put it together right

Posted by on

  • Walter Morris Nov 03, 2008

    I Had The forward sprag in backwards



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Expert
  • 231 Answers

Try to adjust the shift linkage as it may need aduting. Goodluck and remember to rate all replies you get, thanx.

Posted on Oct 29, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do you adjust the shift cable on a 1995 gmc jimmy, wont go into reverse or park.

On the 1995 Jimmy, the shift cable can come loose on the mount on the side of the transmission where the cable meets the trans. When it slips, the alignment goes off and causes the driver to not be able to put the trans into park. If you take a long stick you can push the shift arm on the trans to the park position and your trans will go into park.....what you (and I) really need to know is how to take the shift cable mount apart and reset it.

Aug 05, 2012 | GMC Jimmy Cars & Trucks

1 Answer

I have a 1988 chevy c1500 pickup, its a 5 speed manual transmission i was shifting gears and i was in second goin to third and it wouldnt leave second gear, i could put the clutch in and it would be in...

If this problem is only between 2nd and 3rd. and everything else is normal you are talking about pulling the tranny. See if you can run it throught the gears with the engine off then you have a bad syncro ring. Rebuilding a trasmission is not for the faint of heart. there are a lot of special tools, you need a press. Not really a diy project unless you have friend who is a mechanic and has the tools.

Jan 21, 2011 | Chevrolet C1500 Cars & Trucks

1 Answer

Transmission is sticking in second and third gear, im pretty sure this isnt a slip, and im pretty sure that it doesnt need to be rebuilt, but i wanted another opinion

i bet your wrong too, if its not a blocked filter in the box i would say the seals are leaky and thats why it wont shift up or down gear,,there is a seal swell type of auto box oil you can get you just tip it into the gear box filler pipe and let it do its job if its going to work it will in a fuw miles of running

Jun 13, 2010 | 2002 Pontiac Grand Prix

1 Answer

Rear end humming noise

check the play in the pinion gear bearing on the rear end i think! you will find the yoke ie lose and also the bearing has excessive play and needs ro be changed

Jan 22, 2010 | 2000 Chevrolet Blazer

1 Answer

1988 chevy c1500 problem with second gear

be 1988 and Im sure it has high miles, sound like worn transmission, transmission flush and replace it with new fluid might help some. get use tranny from a junk yard better and cost lot less than rebuilt. being GM mechanic for many years i see transmission on a truck with 100k tend to have leaks or need rebuilding. again i see some have better luck but rear.

Aug 31, 2009 | 1988 Chevrolet C1500

1 Answer

Transmission wont shift to third

If you have lost third you have an internal problem. It will either be the input carrier, third/forth clutches, or a valve body issue. You may price a rebuild job at a trans shop, or a trans from a wrecking yard. 700R4 trans is getting hard to find from wrecking yards. Good Luck

May 19, 2009 | 1984 Chevrolet Camaro

1 Answer

Transmission not passin to third gear

Can you shift it manually with the shifter? Like have it in second gear and put it in 3? If it shifts check vacuum hose to modulator.

Apr 23, 2009 | 1998 Buick Regal

1 Answer


Test the transmission module. It controls everything the transmission does, the timing of shift points, gear selection, overdrive, etc

Jul 28, 2017 | 1995 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides