Question about Chevrolet Blazer

Open Question

Replacement of oil pump for 2000 chevy blazer

How to replace oil pump

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 124 Answers

SOURCE: 2002 chevy blazer fuel pump (4 door)

yes you have to drop the tank. you will also need a fuel line tool to unhook the fuel lines. before you drop the tank see if tou can reach and wiggle the electrical connection on the top of the tank. these pumps have a pigtail issue. please rate

Posted on Dec 08, 2008

Ad
  • 1 Answer

SOURCE: 2000 chevy blazer, truck cranks

Does your battery go dead?

Posted on Dec 18, 2008

dennymulford
  • 1055 Answers

SOURCE: I have a 2000 Chevy Blazer I have replaced

maf sensor, tps sensor,or timing gear

Posted on Apr 16, 2009

  • 324 Answers

SOURCE: how replace turn signal switch 2000 chevy blazer?

Since the 2000 chevy blazer is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.

Posted on Oct 07, 2009

emissionwiz
  • 76164 Answers

SOURCE: replace lower ball joints on a 2000 chevy blazer 4

Raise vehicle up on jack stands so that the stands are under the lower controll arms and the suspension is "loaded" Remove the front tire(s) (if you break the torque on the nuts while the wheel is still on the ground it helps, but do not loosen them completely as you will be looking for new rims and wheel studs too). Place a drift or some other suitable object in one of the brake rotor vanes so that it will hit the brake caliper and stop the rotor from moving and remove the CV shaft nut (it's a big ****** make sure you have the right socket on hand before getting to this point). Next remove the brake caliper and rotor then undo the wheel bearing retaining bolts and remove the wheel bearing. This should give you enough room to move the axle shaft back and up so you can work on the ball joint. If you've had ball joints replaced before just unbolt the ones that are installed and using a pickle fork, or a block of wood and a hammer, drive the ball joint stud from the knuckle. (make sure to support the upper control arm so it doesn't drop down on you when you do this) If you are working on original ball joints then I reccomend placing a block of wood or something else that will protect the cv boots from drill bits ect and drill out the rivets holding the ball joint in place. then remove in the same manner indicated in the previous paragraph. installation is pretty much the reverse of removal and don't forget to torque your cv shaft nut I have a 1999 and the manual specs 103FTlbs... This is a critical torque as it helps preload your wheel bearing. Too high and you'll burn them up, too low and they'll be loose and wear out.

Posted on Oct 08, 2009

Testimonial: "Thank you for your directions this will help very much."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2000 chevy blazer is knocking, but from the front of the motor, has good oil pressure. changed the oil & there was very very minute dirt/shavings. Transmission has been acting up going into 2


Check the water pump in the front of your engine for bearings going out. Have your tranny fluid changed & have the 2 shift selonods replaced, if the tranny is OK.

Feb 15, 2015 | 2000 Chevrolet Blazer

1 Answer

2000 chevy blazer wont start intermittenly


You'll have to figureout if it is a fuel or ignition problem.Isthe check engine light on ?
Was the fuel pump you installed a GM or aftermarket ?

Jul 01, 2012 | 2000 Chevrolet Blazer

1 Answer

Where is the oil pump located on a 2000 chevy blazer and how do i replace it?


In the oil pan. The pan needs to be removed, and sometimes the transmission needs to be removed, or lift the engine up off the motor mounts. Not an easy task.

Jun 14, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

2001 chevy blazer, have replaced fuelpump,filter,fuel pump relay.Fuel pump does not run everytime key is turned to start.When pump does run the engine runs for a short time and quits.When I try and...


when replacing fuel pumps on alot of chevys its recommended to replace the harness also or you can have repeated fuel pump failures. Do a search on,, why repeat fuel pump failures;; and you'l have some info to go on.

Nov 26, 2009 | 2000 Chevrolet Blazer

1 Answer

I have a 2000 Chevy Blazer I have replaced


maf sensor, tps sensor,or timing gear

Apr 16, 2009 | 2000 Chevrolet Blazer

1 Answer

2000 chevy blazer


check the crankshaft sensor

Jul 17, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...