Question about 2007 Nissan Maxima 3.5 Sl Sedan

1 Answer

07 nissan maxima passenger side headlight and fog light dimmer then driver side

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 76,649 Answers

Check near the headlight for loose or corroded chassis ground connection to the headlight.

Posted on Feb 22, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
snownbird33
  • 120 Answers

SOURCE: Car won't start

Hi, does the alarm shut off when you unlock the passenger door?
If it does not I will give you a test that you can do.
1. disconnect the harness anti-theft control module. (loctaion depend were you live USA next to fuse panel Canadian models above the glove box.) Check the continuity between Light Green/Black wire and Black wire of the anti-theft control module.
2. Continuity should not be there with the door lock in, lock or neutral position. With the door lock in-between lock and neutral position (any door) continuity should be present.
3. If continuity is as specified replace the anti-theft control module. If continuity is not as specified, check operation of the door lock switches.I will add that test at bottom.
4. If the door lock switches are ok check the continuity og LIGHT/BLACK wires between anti-theft control module and door lock switches. Check Continuity of BLACK wire between door lock switches and ground. Continuity should be present if Continuity is not present repair harness or connectors.
5. If Continuity is present, check continuity LIGHT GREEN and BLACK wire of anti-theft control module. Continuity should not be present with trunk lock in lock or neutral position. With trunk lock in-between lock and neutral position, Continuity should be present.
6. If Continuity is as specified replace anti-theft control module. If Continuity is not as specified, check operation of truck lock switches. If necessary replace trunk lock switch.
7. If trunk lock switch is ok, check Continuity og LIGHT GREEN wire between anti-theft control module and trunk lock switch. Check Continuity of BLACK wire between trunk lock switch and ground. Continuity should be present. If Continuity is not present repair harness or connectors.

DOOR LOCK SWITCHES
Disconnect 4-pin door lock switch connect (left and right front doors) With door lock in neutral, full lock or full unlock position, there should be no continuity between any terminal and BLACK wire terminal. Continuity should exist between LIGHT GREEN?WHITE wire and BLACK wire terminals with door lock in-between neutral and full lock position. Continuity should exist between LIGHT GREEN/BLACK wire and BLACK wire terminals with door lock in-between neutral and full unlock positions. If continuity is not as described, replaced door lock switch.

Hope this help its a place to start. let me know if you need anything else.

Cheers

Posted on Aug 23, 2008

SOURCE: 2004 nissan maxima passenger side window will not roll up

you window must have slipped off the rolling pulley that pushes the window up or one of the plastic pieces is broken that holds the window.

Posted on Nov 02, 2008

  • 383 Answers

SOURCE: 2005 Nissan Maxima SE Fog light replacement

jorgeva: on the driver's side to gain access, you must remove the air cleaner assembly. At that point, you can see the back of the light which has a plastic cap. Rotate this "counter clockwise" and you can pull it back from the back of the lamp housing. From there you will see how the bulb it self is plugged in, which is obvious. Unplug it. There is a "spring "like latch retainer to hold the bulb in place. Unlatch it, remove the bulb and install the new bulb.
CAUTION!!!!!!! DO NOT TOUCH THE GLASS AREA OF THE NEW BULB! Only handle the rear section. Reassemble in the reverse order.
The right side will require the removal of the windshield washer tank.
I trust this will have answered your question. If you would, let me or FIXYA know if I have solved your problem......

Posted on Apr 18, 2009

  • 1986 Answers

SOURCE: 2002 nissan xterra headlight is aiming up too high

on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 14, 2009

  • 1986 Answers

SOURCE: Drivers side headlight assy change, Nissan Sentra

Just unscrew the screws holding down the black tabs on top of the headlights and you have to gently pull the headlight out , be careful because the bottom of the headlight has a tab holding it in place (be patient might have to move it around to release the bottom tab). And do the opposite when putting the new headlights on. Even if the bottom tab breaks. the tabs on the top will old the headlight in place. Once it's changed, you'll need to re-aim the headlights...

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MY DRIVERSIDE HEADLIGHT IS DIMMER THEN THE PASSENGER SIDE


You have a bad GROUND going to the dim light. Either the ground wire is broken, not connected or not making contact at the bulb.

Mar 29, 2014 | Pontiac Grand Am Cars & Trucks

1 Answer

2004 Maxima, front, rear running lights, dash dimmer don't work. Lamps and fuses are good. Possible cause(s)?


All lighting fuses and relays are in a plastic box under the hood close to the battery on top of the inner fender well. Do not mess with the computer, it has nothing to do with the lights. check every fuse in the box under the hood.

May 23, 2017 | 2004 Nissan Maxima

1 Answer

Headlight come on , replace dimmer bulb but light comes on and goes back out. could it be relay or switch itself. The light and fog light work on driver side but not passenger side. IThis problem occur...


it sounds as though there is a loose connection on the passenger side. Check socket and switch bulbs from driver and passenger side. hope this helps tim

Sep 05, 2010 | 2001 Hyundai XG300

1 Answer

What size bulb is an audi s4 headlight and fog light?


SYLVANIA H7 SILVERSTAR HIGH PERFORMANCE HALOGEN HEADLIGHT BULB -- 55 Watts, Single C-8 filament for use as either high beam or low beam; 100 percent legal halogen headlight bulbs; Features the whitest and brightest light colour similar to daylight for safer night driving; Meets all US FMVSS 108 and Canadian CMVSS 108 requirements. Fits Driver or Passenger Side Driver or Passenger Side Fits the following vehicle/s
2004 Audi S4 Base 8 Cyl 4.2L 2004: Base; 8 Cyl 4.2L RAMPAGE FOG LIGHT, BLACK METAL HOUSING, With round clear lens; Includes 100-Watt H3 halogen bulb, one lamp and a single bolt mounting system; Provides better illumination Fog Light

  • Fits the following vehicle/s: 2004 Audi S4 Base 8 Cyl 4.2L 2004: Base; 8 Cyl 4.2L;

Jun 24, 2009 | 2004 Audi S4

1 Answer

Fog lights on a maxima 2004


you can access those by removing the coolant overflow bottle on passenger side and air filter box on the drivers side. you do not have to go into the wheel well area at all.

Sep 23, 2008 | 2004 Nissan Maxima

1 Answer

Fog light


Replace the bulb. It may look good but its NOT. See it all the time with Maxima fog lamps.

Jul 15, 2008 | 2004 Nissan Maxima

Not finding what you are looking for?
2007 Nissan Maxima 3.5 Sl Sedan Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...