Question about 1998 Buick Regal

1 Answer

HOW TO DO CRUISE CONTROL SELF DIAGNOSTIC

CRUISE CONTROL STOPPED WORKING. FUSES OK, BRAKE LIGHT TEST OK.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Check the wires. This happened in my grandmother's car. Mice chewed through her cruise control wires and f;d everything up. Check continuity between the wires from PCM to output on your wiring diagram.

Posted on Feb 22, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to fix Cruise Control


The most common problem on this vehicle is the sensor right on the master brake cylinder the seal goes out and brake fluid gets right in the sensor ruining it that is the most common problem lete no if it helps

Sep 22, 2014 | 2001 Ford Windstar

2 Answers

Why wont the cruise control work on a 2005 ford taurus but the cruise light comes on


The first thing to check is the tail lights. The cruise control will not work if any lights are out. Changing to LED tail lights also causes the cruise to not work.

Apr 06, 2014 | 2005 Ford Taurus

1 Answer

What do i do if the cruise control self test does not work


there is no self test I know of. First, make sure your brake lights go on and off ok when you step on the brake. The brake switch deactivates the speed control when depressed.

Next, check the fuse for the speed control. See owner manual for fuse charts.

Next, what happened when it quit? Suddenly, cut of while driving? etc.

Oct 29, 2011 | 2001 Ford F150 Styleside SuperCrew

2 Answers

I have a 2002 ford f150 and the cruise has quit. I can't find my owners manual and i would like to know where the fuse is. I am pretty sure it is in the box under the hood. but which one is it?


Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be a blowed fuse in the recall harness, if you did have it done.

Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in the recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked. The switch is on the front of the master cylinder,

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped)

Good luck, i hope this helps.

Jul 02, 2011 | Ford F-150 Cars & Trucks

1 Answer

Which fuse is for cruise control in 2003 ford f150


The fuses for the speed control from the factory are :
Engine Compartment fuse panel #7,
Cab fuse panel Fuses #15, #13, #5

The fuse that goes to the recall part is Fuse #13, 20A

The recall is 05S28. Description: Speed Control Deactivation Switch.
The part number for the recall is : 1L1Z-9F924-AA
The part has a fuse inline that is marked as non serviceable, but 1 revision I saw, it was just an ATM fuse under tape. Not sure if this is the final revision that was used on your truck ( or should have been used ).


The self test for the Cruise Control ( for 00-03 MY, with the CC light on the cluster ) :

With the key off depress and hold the cruise control off button while turning the ignition to the run position,don't start the truck, the cruise light will flash once to let you know it is in self test.
Five additional flashes indicate a bad cruise control servo

Release the cruise off switch and within 5 seconds depress the other switches in sequence:
1. on
2. resume
3. coast
4. set/ accel
The speed control light will flash as each switch is depressed.

If the last one does not flash it may then flash a code

After this the cruise will move the throttle to test the actuator and the cable.
Make sure the throttle returns to idle and turn the key off.
----------------------

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

- 3 flashes - deactivator switch is open or circuit defective.

- 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 19, 2010 | 2003 Ford F150 Regular Cab

1 Answer

2001 F-150 cruise control stopped working. Already checked the fuse and it's good. What's next


really tough to do on the net but first we need to know about any codes...

Hold speed control OFF button, and turn ignition switch to RUN position. CRUISE indicator should flash once to indicate successful entry into self-diagnostic mode. If CRUISE indicator does not flash, start procedure over. If CRUISE indicator still does not flash, repair system by symptom there might be some switch concern

If CRUISE CONTROL indicator flashes once followed by 5 additional flashes, replace speed control servo/actuator.

Release speed control OFF button. Within 5 seconds in entering self-diagnostics, press speed control ON button. Press remaining speed control buttons in the following sequence; ON, RES, COAST and SET/ACCEL.

As each button is pressed, CRUISE indicator will flash.

Wait until indicator light goes out, then press next button. After sequence has been completed, indicator light will flash to indicate test passed or failed. With the codes we can then better diagnose your concern

Immediately after static test has passed, actuator performs a dynamic test by automatically operating throttle .04-.40" (1-10 mm). Observe throttle movement to witness any sticking in cable or linkage. Ensure throttle returns properly. Turn ignition switch to LOCK position. If self-diagnostics do not pinpoint fault there is more we can do but tough over the net

Mar 26, 2010 | 2001 Ford F150 Styleside SuperCrew

2 Answers

2002 Ford F150. Cruise control stopped working.


Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be a blow fuse in the recall harness, if you did have it done.

Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

Feb 22, 2010 | 2002 Ford F150 Regular Cab

1 Answer

Cruise control will not turn on. light on dash use to come on. cruise will not work. checked fuse it is ok


Did you have the recall for the cruise control done ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be the fuse in the recall harness is blown.

Try the Cruise Control Self test :
----------------------------------
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.
----------------------------

If the Cruise Control does not enter self test, the fuse in the recall harness ( if done ) is most likely blown and needs to be replaced.

Feb 02, 2010 | 2002 Ford F150 Regular Cab

2 Answers

Brake lights and cruise control are not working. Checked fuses and lamps all are ok.


sounds like a faulty brake light switch located down by the brake pedal

Nov 30, 2009 | 2005 Chevrolet Colorado

Not finding what you are looking for?
1998 Buick Regal Logo

564 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...