Question about 2000 Chevrolet Silverado 1500

Open Question

Chi got a 2000 chevy silverado with a 5.3 when its if u go to take off it will buck or if i hold it to the floor it will back fire .got mass air flow sensor code

Chage plug, wires, fuel filter, fuel pump

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

leetamara
  • 702 Answers

SOURCE: having problems with my 96 chevy tahoe mass air flow

The MAF (Mass Air Flow) sensor is a very common problem with these along with the pickups. This isn't what you would call an inexpensive part. Definitely do some shopping before you buy one.

Posted on Nov 10, 2008

dennymulford
  • 1055 Answers

SOURCE: I have a 2000 Chevy Blazer I have replaced

maf sensor, tps sensor,or timing gear

Posted on Apr 16, 2009

  • 34 Answers

SOURCE: 1997 chevy silverado 1500 350 vortech, new fule pump not working

before you drop tank again, check fuses & relay.then disconnect fuel line @ filter turn key to on position should hear fuel pump run and get gas stream out of line. if no flow from line new pump faulty be sure & remove negative battery cable first good luck.

Posted on Jun 20, 2009

  • 5 Answers

SOURCE: looking to findthe mass air flow sensor on a 89 chevy corsica

location is under the hood where the aircleaner is there is an electrical connection that plugs into the mass air flow sensor

Posted on Oct 09, 2009

  • 41 Answers

SOURCE: my van when pressing on gas pedal jerks while

could be two things, 1; the coil is going bad. 2; the electronic egr valve has a piece of carbon in it. the latter is probably the problem. to fix this , just remove the valve, push on the piston and while holding it in the open position, spray with carb cleaner and blow it out, release the piston and be sure the valve is closing all the way. if the gasket is damaged you can get a new one at the parts store.

Posted on Dec 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a 2000 Chevy Silverado 1500 4.3 motor have a intake air temperature sensor


Yes it does, it is located between the mass air flow sensor and the intake, you shouldn't have any trouble finding it.

Feb 22, 2015 | 2000 Chevrolet Silverado

1 Answer

Silverado mass air flow sensor


the map sensor could be the problem for code P0101
hope it helps

Mar 27, 2014 | 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

2004 chevy 2500HD Truck OBD2 trouble code P0101


Hello and welcome. this code P0101 indicates a problem with the mass air flow sensor. this usually requires the replacement of the mass air flow sensor. but there will be a few checks to be made before the sensor can be condemmed

Oct 23, 2010 | 2003 Chevrolet Silverado 2500HD

1 Answer

2000 Chevy Silverado occasionally won't hold idle when starting


Try cleaning the throttle body and the mass air flow sensor.Does your check engine light come on?

Nov 25, 2009 | 2000 Chevrolet Silverado

1 Answer

Air flow to defrost or floor not switching stays on dash vents


cannot switch from defrost to panel airflow 2001 chevy silverado

Oct 06, 2009 | 2001 Chevrolet Silverado

2 Answers

My 2000 Chevy Silverado has trouble code P1133.


some cars do have recalls for bad codes being thrown check your dealership and if theres no problem they can block the code so your engine light will not come on for that code

Jun 30, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

2000 Boniville bucks like a horse and trys to stall


that could be it. but it could be the timing too i think.. if you run the car and its hot when it starts to buck and stalls.. the rubber belt could be getting warm and expandig and causing it to slip out of timming just a hair.. then you let it set and cool down the belt then re-cools and runs fine. that or it could be just simple needing new wires and plugs. if they are mis firing and then the plug misfires completely it will cause the car to buck and stall out.. i personally would check wires and plugs then the distributor block make sure there are no mis firing there also.

Jun 28, 2009 | 2000 Pontiac Bonneville

1 Answer

MAF sensor and injectors


the mass air flow sensor is located between the air filter housing and the air inlet to the intake manifold, remove the two band clamps holding the maf sensor, clean when cold with CRC mass air flow sensor,remember to take off the three wire plug to the maf sensor,get back to me if you need more help,please rate my fix as i strive to be the best,problems,get back to me

May 14, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...