Question about 1999 Dodge Durango

1 Answer

Need 1999 dodge durango fuse panel diagram

I have the diagram that is inside the cover of my fuse box panel. However, it would be helpful if there was something that toldme just what they were...like Panel...what exactly is the panel? I am trying to find the fuse for my speakers and radio.

Posted by on

  • 4 more comments 
  • Patty Feb 22, 2012

    Thank you for the diagram and solution. However, I have unplugged the one that says RADIO and my speakers are still making noised. (Fuzzy buzzing sound) even when the car is turned off. It does this when my battery is going dead.

  • Bonnie Ya?ez
    Bonnie Ya?ez Feb 22, 2012

    The speakers are getting some kind of electrical interfearance which is causing them to power on...is it an aftermarket or origional stereo?

  • Patty Feb 22, 2012

    It is the original stereo. I will have to ask my husband, but they might not be the original speakers??? Would that matter?

  • Bonnie Ya?ez
    Bonnie Ya?ez Feb 23, 2012

    It could be another problem also. A ground could not be connected properly. A capacitor could be malfunctioning. Check the grounds first. Check the capaciters. Let me know if when the car is on, if you are revving the engine, if the noise in the speaker goes up. If it does, then this is because one of the capaciters or resisters in your car is not working properly to suppress the snap of the spike of voltage, causing a rise in frequency which is being picked up by your sound system.

  • Bonnie Ya?ez
    Bonnie Ya?ez Feb 23, 2012

    There are some electronics that are always hot (on) in your car and are supplying voltage to accesories (like alarm, power door locks, etc), so if there is a short to ground, or an improper ground the speakers will be picking up this interfearance.

  • Bonnie Ya?ez
    Bonnie Ya?ez Feb 23, 2012

    Since it's not aftermarket I doubt you have a big subwoofer and amplifier that is causing this. However if there is a factory installed amplifier and the ground came loose, or shorted, this could cause the interfearance in the speakers. Also, behind the radio the wires to the speakers could be in contact with a wire that has voltage running, causing interfearance. Get a hold of wiring diagrams for your stereo if you wish to do it yourself.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Here is the diagram for your Durango. Notice where it says 'RADIO' That is your RADIO
need 1999 dodge durango fuse panel diagram - 2_22_2012_1_33_44_am.jpg

Posted on Feb 22, 2012

  • Bonnie Ya?ez
    Bonnie Ya?ez Feb 22, 2012

    if you open your door there is a little indent where you can pull your 'panel' out, which is connected to the side of your dash. that is where the fuses are located also

  • Bonnie Ya?ez
    Bonnie Ya?ez Feb 22, 2012

    The speakers are getting some kind of electrical interfearance which is causing them to power on...is it an aftermarket or origional stereo?

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: need to know "no bus" indicator light on instrument panel....

"No Bus" means the data cable going to the (PCM) computer is unplugged, or the PCM has failed and not able to read the information it is being given.
Sometimes just jiggling the PCM causes the ODO "NO BUS" to come on.
Sometimes a bad crank or cam sensor can cause this as well.

Here is the OFFICIAL checklist for the "NO BUS" condition....

Vehicle: 1998 - 1999 Dodge Durango 3.9L
2000 - 2001 Dodge Durango 4.7L
1998 - 2000 Dodge Durango 5.2L
1998 - 2001 Dodge Durango 5.9L



Symptom: Engine will not start. Gauges are inoperative. No BUS message displayed on odometer.



System: Body/Chassis Electrical, Emissions/PCM/Fuel, Engine Electrical



Codes: N/A



Problem 1 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Crankshaft Position (CKP) Sensor.



Test & Fix: If the 5v power supply circuit is shorted to ground, the CCD bus is unable to transmit messages and the Powertrain Control Module (PCM) appears to be "dead". The PCM is not damaged when the 5v power supply gets shorted to ground, but does need to be reset by turning the key off for 10 second after the short is removed. Using a DVOM or labscope, measure the voltage on the 5v reference wire at the Throttle Position Sensor (TPS) or Manifold Absolute Pressure (MAP) sensor. If 5v is not present, unplug the Crankshaft Position (CKP) Sensor. Turn the key off for 10 seconds. Turn the key on and measure the voltage on the 5v power supply circuit. If the voltage is now 5v, replace the CKP sensor.



Problem 2 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Camshaft Position (CMP) Sensor.



Test & Fix: If the 5v power supply circuit is shorted to ground, the CCD bus is unable to transmit messages and the Powertrain Control Module (PCM) appears to be "dead". The PCM is not damaged when the 5v power supply gets shorted to ground, but does need to be reset by turning the key off for 10 second after the short is removed. Using a DVOM or labscope, measure the voltage on the 5v reference wire at the Throttle Position Sensor (TPS) or Manifold Absolute Pressure (MAP) Sensor. If 5v is not present, unplug the Camshaft Position (CMP) Sensor. Turn the key off for 10 seconds. Turn the key on and measure the voltage on the 5v power supply circuit. If the voltage is now 5v, replace the CMP sensor.



Problem 3 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Manifold Absolute Pressure (MAP) Sensor.



Test & Fix: If the 5v power supply circuit is shorted to ground, the CCD bus is unable to transmit messages and the Powertrain Control Module (PCM) appears to be "dead". The PCM is not damaged when the 5v power supply gets shorted to ground, but does need to be reset by turning the key off for 10 second after the short is removed. Using a DVOM or labscope, measure the voltage on the 5v reference wire (5v power supply) at the Throttle Position Sensor (TPS) or Manifold Absolute Pressure (MAP) Sensor. If 5v is not present, unplug the MAP sensor. Turn the key off for 10 seconds. Turn the key on and measure the voltage on the 5v power supply circuit. If the voltage is now 5v, replace the MAP sensor.



Problem 4 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Throttle Position Sensor (TPS).



Test & Fix: If the 5v power supply circuit is shorted to ground, the CCD bus is unable to transmit messages and the Powertrain Control Module (PCM) appears to be "dead". The PCM is not damaged when the 5v power supply gets shorted to ground, but does need to be reset by turning the key off for 10 second after the short is removed. Using a DVOM or labscope, measure the voltage on the 5v reference wire (5 volt power supply) at the Throttle Position Sensor (TPS) or Manifold Absolute Pressure (MAP) Sensor. If 5v is not present, unplug the TPS. Turn the key off for 10 seconds. Turn the key on and measure the voltage on the 5v power supply circuit. If the voltage is now 5v, replace the TPS.



Problem 5 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted wire.



Test & Fix: If the 5v power supply circuit is shorted to ground, the CCD bus is unable to transmit messages and the Powertrain Control Module (PCM) appears to be "dead". The PCM is not damaged when the 5v power supply gets shorted to ground, but does need to be reset by turning the key off for 10 second after the short is removed. Using a DVOM or labscope, measure the voltage on the 5v reference wire at the throttle position sensor (TPS) or manifold absolute pressure (MAP) sensor. If 5v is not present, unplug all sensors that are connected to the 5v power supply and disconnect the PCM. Check if either 5v power supply circuit is shorted to ground using a DVOM. If the circuit is found to be shorted to ground, repair the wire and the cause of the short.



Problem 6 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Governor Pressure Sensor.



Test & Fix: If the 5v power supply circuit is shorted to ground, the CCD bus is unable to transmit messages and the Powertrain Control Module (PCM) appears to be "dead". The PCM is not damaged when the 5v power supply gets shorted to ground, but does need to be reset by turning the key off for 10 second after the short is removed. Using a DVOM or labscope, measure the voltage on the 5v reference wire at the Throttle Position Sensor (TPS) or Manifold Absolute Pressure (MAP) Sensor. If 5v is not present, unplug the large round connector on the driver's side of the transmission. Turn the key off for 10 seconds. Turn the key on and measure the voltage on the 5v power supply circuit. If the voltage is now 5v, remove the transmission pan and check for shorted wiring inside the transmission. If the wiring is OK, replace the Governor Pressure Sensor.


Many times the PCM simply overheats - and changing it will stop the problem.


Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 13, 2009

  • 1 Answer

SOURCE: fuse panel

need layout of fuse panel for 1994 dodge caravan

Posted on Jan 23, 2009

emissionwiz
  • 76118 Answers

SOURCE: what size speakers are in 1999 Dodge Durango

Car speaker fit guide - DODGE DURANGO 1999
According to our database, here are the speakers types that go in your DODGE DURANGO 1999 car, along with their location:

  • Front: 6-3/4"
  • Rear: 6-3/4"
  • Front door: 6-3/4"
  • Back door: 6-3/4"

Posted on Dec 17, 2008

ZJLimited
  • 17970 Answers

SOURCE: 1999 dodge durango 5.2 firing order diagram

1999 Dodge Durango 5.2 liter V-8 VIN "Y"

66ccb28.gif


Hope helps (remember rated and commetn this).

Posted on Sep 01, 2010

  • 2841 Answers

SOURCE: I need a free wiring

If you mean the spark plugs then here you go. Curtorsey About.com clay58_63.png

Posted on Aug 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cigarette lighter fuse


There are 2 fuse panels in the '99 Durango. The one containing the Cigar Lighter fuse is on the dash assembly, accessed from just inside the drivers side door on the side of the dash. There is a diagram inside when you pull the cover off. The one you are looking for is a 15 amp (blue) fuse, 4th from the front on the bottom row.

Jan 22, 2015 | 1999 Dodge Durango

1 Answer

Which fuse is for the brake lights on a 2004 Dodge


Google search Fuse diagram for 2004 Dodge Durango Limited 5.7l/ Hemi look around if no answer look on the fuse box cover. Diagram usually located inside.

Sep 01, 2014 | 2004 Dodge Durango

1 Answer

I have 99 dodge durango need to know the fuse number for my AC unit. I think my fuse went. 5.2 liter engine and v-8 4-wheel drive


if you look inside the fuse box cover llid you will ba able to know exactly where it is located and what size it is.

May 21, 2010 | 1999 Dodge Durango

1 Answer

Need a fuse box diagram for 1999 dodge intrepid


Diagrams I have do not show this,all it says is it has a legend on the inside door cap to the fuse panel,I hope this helps,you know there is a fuse/relay box under the hood witch has a legend on the under cover also.

Apr 19, 2010 | 1999 Dodge Intrepid

1 Answer

Blinkers quit working i need a diagram of the fuse box and relays where they go by driver side left leg


Remove the panel under the steering column.(three screws and pull towards seat). Look for white rectangular box with a screw in the midle of it. Remove the screw and the cover and you will find the flasher unit is located inside. Pull and replace.

Feb 17, 2010 | 1999 Dodge Durango

1 Answer

Now, both power ports have stopped functioning on our 200 Durango


For a diagram of the fuses, look inside the cover you removed to get to them. (My 98' has this)

Also, grab a Chilton's book for your local Autozone. I don't know what you mean by 'Power Ports.' Are you referring to the cigarette like outlets inside the cab?

Jul 03, 2009 | 1999 Dodge Durango

1 Answer

Where is the fuse box in a 1998 dodge durango my interior lights won't come nor my panel lights i can't see my speedometer


the fuse panel is right inside the driver side door, open the door and look at the side of the dash there it is...

Jun 09, 2009 | 1999 Dodge Durango

1 Answer

No diagram for the fuse box


Its a fuse. find the fuse box, sometime's there is more then one. Most are inside the drivers side panel. pull out the cover and read the back of the cover. It list the fuse's and their function. Be brave pull out a few fuse's and see if any have a burned wire in the middle. Or simply compare the fuse's you pull out untill you find one that doesnt look right compared to the others. Make sure you replace the burned out fuse with the proper amps, youll see. good luck.

May 03, 2009 | 2006 Dodge Durango

Not finding what you are looking for?
1999 Dodge Durango Logo

6,921 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...