Question about 2000 Chrysler Cirrus

Open Question

My fan only comes on high on my 2000 chrysler cirrus

Posted by on

  • rick
    rick Feb 22, 2012

    do you mean the fan inside the car for the heat, or the fan under the hood?

  • rick
    rick Feb 22, 2012

    if it is the fan for the heat then you need a blower motor resistor

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: how do I change the

I did a Google search "How do you replace the rear spark plugs on a 2000 Chrysler Cirrus?" and found this link: http://www.faqs.org/qa/qa-6243.html

I haven't tried it yet and am thinking of purchasing a Chilton manual just in case, but as far as explanations go the one at the very bottom of the page in the link sounds the most legitimate so far.

Besides, I have to pay you guys $9.99 for one answer that I can get for free; or I can get the Chilton and have a whole heap of answers for around $20.

Posted on Jul 14, 2008

Sgt Fluffy
  • 157 Answers

SOURCE: where is the spark plugs located on a 2000 chrysler cirrus.

Follow the ignition wires down.

Posted on Jun 10, 2009

  • 26 Answers

SOURCE: 2000 Chrysler Cirrus. No Start, No Spark and no

Sorry I'm not sure if i already posted, My computer did a quick trip for some reason, anyways,

Does the car crank over? What happens when you turn the key and try to start the car? What sound do you hear..

If it cranks do you here the fuel pump?

If it doesn't Here are just a few things, You need to make sure the battery has a full charge and the cables/wires are clean and tight on both ends.

Check you're Fuel Pressure, Check your ASD relay under the hood. This relay powers the fuel pump and Ignition system. It is inside your power distribution center under the hood. moz-screenshot.png

Posted on Sep 06, 2009

  • 2841 Answers

SOURCE: steering is really stiff after replacing power

Is the drive belt adjusted properly. Did you bleed all air from the system after installing the pump? Start the engine and turn the steering wheel from left to right fully 10 times. This will remove any trapped air. Check the fluid level and top it off.

Posted on Nov 21, 2009

  • 34 Answers

SOURCE: How to replace water pump

In short, to replace the water pump you need to disassemble a good deal of the passenger side of the engine. Without a lift, this is not a easy job at home. If you really want to do it yourself, I highly recommend you get a Haynes manual for the car. It's invaluable for a large job like this. Just be prepared for a long job. The shop manual for this calls for 5.5 hrs. That's a mechanic with experience, a lift, and all the right tools. One huge suggestion for you though. Replace the timing belt while you are in there. Its a cheap part, and honestly it'll fail someday. This will save you another headache's worth of labor for one little part.

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace resistor on 1999 chrysler cirrus a/c heater blower only working on high IF I pull the switch out--still have the same problem==what's next???


According to the wiring diagram, it looks like the blower motor is grounded thru the resistor which is grounded thru the fan switch on the dash. High speed bypasses the resistor.
If you have power on the terminals coming out of the resistor, the problem could be in the fan switch.

Apr 09, 2013 | 1999 Chrysler Cirrus

1 Answer

Heater control nob its only blowing on high the others aint working


you have a bad blower resistor . very easy to change

Nov 25, 2012 | 2000 Chrysler Cirrus

1 Answer

Heater fan only works on high


more then likely its the fan resistor doing this. a fan resistor has different diodes or coils for each setting on fan motor. from low to high. it is under dash on passengers side. you have to remove cover held on by retaining clips, the resistor is mounted under the dash by 2 bolts. it has 2 wires going to it. the best place to buy one is at a local auto parts store. for the dealer will rip you off, big time. good-day !

Jan 21, 2012 | 2000 Chrysler Cirrus

1 Answer

Heater fan switch worxs on high only


You have a faulty blower motor resistor. This is located under the passengers sdie dash close to the blower motor.

Mar 19, 2011 | 2000 Chrysler Cirrus

1 Answer

Replaced thermostat but the car still runs hot


I would say check into your water pump and your radiator. Also, while your car is idling, make sure that your fans are coming on. If your fans aren't coming on that will be your problem. Worst case scenario you have a blown head gasket.

Mar 09, 2011 | 2000 Chrysler Cirrus

1 Answer

If the fan for the heat/air/defrost does not work at all, generally speaking is it the fan motor or the resistor? The car is a 2000 Chrysler Cirrus, can you tell me where each of those are located?


If the resistor was bad, the fan would work on high mode only. I would say it's more likely the motor then. There is a panel under the glovebox on the passenger side you must remove. There's a good size black cylinder, vertical, close to the left wall of the car. That's the motor. The resistor is to the right of that, held in by a small hex screw. I changed my resistor about a year ago, about 20 dollars at the parts store. The motor should be between 50-70 (found some at AutoZone for those prices). This is all from memory of when I did that last year.

Dec 05, 2010 | 2000 Chrysler Cirrus

1 Answer

I bought a 2000 chrysler cirrus lx and the car is idleing high why is that?


before you spen money on a idle control valve look at the engine breather pipes,and look good for a split or perished pipe

Aug 27, 2010 | 2000 Chrysler Cirrus

1 Answer

I have a 2000 Chrysler Cirrus. When it rains,


Check Battery, all battery connections, the ground from motor to frame and from battery to motor and or body. A poor ground connection can cause all kinds of problems. Also i had a car that would not start in high humidity that turnedout to be the starter. It was pulling too much juice from the battery at high humidity.

Jul 26, 2010 | 2000 Chrysler Cirrus

1 Answer

2000 Chryler Cirrus - engine races all the time


Either the throttle body is being held open by something or the idle control valve is stuck open. Check where the throttle cable hooks to the throttle body, make sure the cable is not caught on something.

Jan 10, 2010 | 2000 Chrysler Cirrus

Not finding what you are looking for?
2000 Chrysler Cirrus Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...