Question about Cars & Trucks

Open Question

Need instructions manual for John Alan looms

Loom by john alan

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Mk2 1991 gti 8v wiring loom

You have blown up the ecu as a result of not having a good earth connection from the earth lead on the gearbox.
This is a very common problem (done it myself!)
Only solution is to get the ecu repaired or replaced.
You must change the oil and filter before trying to start the car again.

Posted on Jul 02, 2008

keemo68
  • 1263 Answers

SOURCE: towbar wiring

they do sell wiring harness for towing applications, however being that your vehicle is a german manufacture no ordinary wire will work because the color codes are usually different from what we use in the states. i would go and get the right wire harness to prevent and shorts from happening..........please rate this..thanks

Posted on Aug 31, 2008

3bachelors
  • 52 Answers

SOURCE: Tow bar wiring

use the wires inside the hatch behind the plastic panel on either side. Wiring for your car is as follows - 












Parking Lights YELLOW (-) 1K OHM RESISTOR AT THE STEERING COLUM HARNESS USE A 1KOHM RESISTOR Brake Lights WHITE/TAN (+) AT SWITCH Reverse Lights VIOLET/BLACK (+) 72 PIN CONN POS 6 BEHIND PASS KICK







Good Luck, NGK

Posted on Sep 04, 2008

  • 27 Answers

SOURCE: 2004 A4 Avant stereo wiring loom cut

leave it to a specialest or maindealer

Posted on Nov 07, 2008

tripletauto
  • 1450 Answers

SOURCE: Replace front brake pads 2000 Chevrolet Blazer

yes remove one bolts where caliper bolts to the slide assembly older models had allen heads

Posted on Dec 05, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lamda sensor wiring


That's great, Alan, good to hear. Guess you don't need an answer for that! Maybe it will help others looking for a solution to their problem.

Oct 04, 2015 | Cars & Trucks

1 Answer

Wher is the vacuum valve located


Hi John
This link gives the location and operating check..
The Chad Experience
Regards
Alan

Jul 10, 2014 | 2001 Nissan Altima

1 Answer

Bosal towbar wiring problems....


Did you ever solve the problem with the location for the orange wire as I have exactly the same problem, thanks

Apr 22, 2013 | Cars & Trucks

1 Answer

I have an 1988 chevy celebrity 2.8. while driving, it will just all of a sudden lose power kinda like turning off the key and back on i have replaced ignition module, plugs and wires, mass air flow, map...


Hi Charlie, I suggest you replace the fuel filter and have the fuel pump pressure tested for correct output. Have a diagnostic scan carried out. Regards John

Nov 11, 2012 | 1988 Chevrolet Celebrity

1 Answer

My brake lights stay on and when i press on the brake it does not come off


Hi Alan, Sounds to me as if the brake light switch needs to be replaced. Regards John

Oct 24, 2012 | 1991 Honda Accord

1 Answer

2003 sunfire won,t start, turns over but does not get spark, any suggestions would be greatly appreciated


Hi Alan, Have the vehicle scanned with a diagnostic scan tool. The problem may be a crankshaft or camshaft pickup sensor. The scan will pinpoint where the problem is. Regards John

Oct 06, 2012 | 2003 Pontiac Sunfire

1 Answer

Color of wires


Hi Red, Sorry to tell you this pal, but the Toyota's we have worked on do not have a colour coding format for most of the wiring loom. A cable which is loomed from the speed sensor can be one colour going in and another colour coming out because Toyota join cables of any colour, presumably for cost effectiveness. The cable can be identified from the pin number inside the management computer, or by downloading a pin out diagram from <www.allpinouts.com> Regards John.

Oct 06, 2012 | 1996 Toyota RAV4

1 Answer

Wen i put a/c engine of


Hi Alan, The problem with your vehicle would seem to be the solenoid which controls the engine up idle, increasing the engine speed when you select the AC operation. As you have forgotten to tell us which vehicle or any other details about the vehicle we cannot give you more help. Regards John

Aug 25, 2012 | Cars & Trucks

1 Answer

Clutch fan removal left or right . the replace part shows left hand but is it the right part cant get clutch fan off


Hi Alan, It will be fitted opposite to the rotation so that it does not loosen accidently. Regards John

Aug 19, 2012 | 1997 Chevrolet Astro

1 Answer

Have a 96 ek3 1.4 civic. ditched 1.4 engine for a b18c1 sir..used 1.6 vti engine loom and used a 1.4 dash loom car wont run right any ideas what might be wrong????


sorry to say when you cobble engines and wire harness, there are now diagnostic procedures in any book or manual, there are to many things that could be different. even one wire wrong in a wire loom can impossible to figure out...

Dec 29, 2010 | 1996 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...