Question about 2003 Toyota Camry

Open Question

Toyota Camry O2 sensor bank 1

How do I know which sensor is bad

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1252 Answers

SOURCE: I am looking for the location of O2 sensor ( Bank

michael_cass_19.jpgHere it is ....

Posted on Jun 06, 2011

  • 2004 Answers

SOURCE: vsc vsc off check engine

Disconnect your battery for 10 minutes after which you connect it back the lights should go off. Don't report to toyota. Nigerian style!

Rate this............

Posted on Mar 21, 2009

  • 175 Answers

SOURCE: O2 Sensor problem

this pic with be the fix ya

Posted on Apr 10, 2009

  • 318 Answers

SOURCE: i have my check engine light on and a p0031 error

On toyotas this is almost always a failed o2 period. Take it somewhere and have it put in. On v6's it is not that easy to get to.

Posted on Jul 10, 2009

  • 7353 Answers

SOURCE: have p0130 and p0133 codes 98 toyota tacoma

I would check the O2 sensor, and if it checks bad, replace it, and clear the trouble codes. If the light comes back on, you may need to check further. .

Posted on Oct 28, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I would to know if a bad transmission speed sensor can cause the car to jerk when you shift into drive or reverse

Hard to tell without knowing what year, make, and model of vehicle we are working on here. A speed sensor would not cause this, but bad engine or trans mounts could, or possibly a sticking valve body in the transmission.

Feb 19, 2016 | Cars & Trucks

1 Answer

I have a 2002 honda 500 rubicon it is blinking three gears d1 d2 els all at once

the D lights blink for A/T failures
in the USA (are you) the first check is to scan it.
(and drive it checking for slip,flare or other symptoms)1st !!!
connect the scan tool 0bd2 and scan it for tranny errors)
if you read the FSM , it shows each step in sensor tests.
and lots of not..... (scope readings missing, bad bad bad)
first off , you need some facts:
if the scan tool shows the rear (wild guess) speed sensor reads wrong, do not think its bad, you fail to realize most failures
are the transmission slips (trans, is bad) and the sensor see this illegal
low rpm and trips a DTC for that.
most those sensors last forever,
THe ECU (PCM) never knows what is wrong, it only knows
what tests fail,.
The ecu knows the speed of the engine and the tranny speeds.
this is the TCM function (be it in a TCM box or in the PCM)
this TCM does all the shifting and monitors for errors.
The DTCs in many case should state, tranny slip or bad sensor.
and dont.
you didnt post the DTCs so can elaborate.
working the A/T with no FSM. is not going to work.
you need to read the on car service, and do the steps in the correct order. fiddling a sensor with a tranny with low pump pressure. is folly
so is same and the stall test fail. (1st tests both)
my byline:
"the PCM is dumb. it never knows what part is failed, ever.!!!"
think of DTCs as only clues, or 1 more symptom....

Nov 29, 2013 | Honda Cars & Trucks

1 Answer

Crankshaft sensor how you know it's bad

It is hard to see,wait until get bad.

Feb 21, 2013 | Cars & Trucks

1 Answer

Cod 51 means o2 sensor is bad but tell me please which o2 sensor is bad .upstream or down stream sensor

Oxygen sensors code sometimes produced because of some other problem, blocked exhaust or cat converter, over rice fuel supply or vacume leak in intake manifold giving a real lean mix and so o2 out of range in both casesw

Dec 10, 2012 | Cars & Trucks

1 Answer

P0154 Trouble Code on my 2002 Mitsubishi Montero Sport. Where exactly is the bad 02 sensor? There are four of them and I don't know which one is the Bank 2 #1 sensor.

Bank 2 is the side of the engine with cylinder number 2, and sensor one is the sensor in front of the catalytic converter.
Please know that the code does not mean the sensor is bad, only that the reading the computer is getting is constantly lower than .3 volts.
The sensor could be faulty, or there could be a problem with the fuel injectors or the wiring harness to the sensor.
When the sensor is working correctly, the reading should switch back and forth between .3 and 1.0 volts.

Sep 18, 2012 | Mitsubishi Cars & Trucks

1 Answer

O2 sensor bad, when I have auto zone hook up and test they do show o2 sensor bad, but the codes are saying sensor 3 and 4 are bad. it doesn't say "bank 1 sensor 2". how do I know what...

You will have a total of 4 O2 sensors, two on the left (driver's side-Bank 1) and two on the right (passenger side - Bank 2). Sensor 1 is before cat. convertor and sensor 2 after cat. converter. Hope this helps.

Sep 09, 2011 | 2001 Dodge Dakota

2 Answers

I do not know it is PO160

Hi and welcome to FixYa!

May I know the make and model of the car please for us to know what the fault code will mean. Thanks!



Jan 26, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

1998 saturn running rich seems to be getting to much fuel. What would cause this?

air intake sensor, throtle body sensor, throtle body, bad air filter, bad fuel filter, bad tempature sensor.

good luck let me know if you have any questions.


Mar 15, 2009 | 1993 Saturn SL2

Not finding what you are looking for?
2003 Toyota Camry Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides