Question about Chevrolet Silverado 1500

Open Question

1998 chevrolet silverado 1500-''remove front wheel hub

Replace speed sensors,front hubs,bearings

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 124 Answers

SOURCE: noisy front wheel bearing

Yes the bearings can be changed on this truck. The bearing races will need to be removed from the rotor to do this use a punch and hammer once the rotor is removed. You will need inner bearing and race, outer bearing and race, and a seal, plus grease to pack the bearings. The hub on these trucks is the rotor. Please rate.

Posted on Dec 12, 2008

Ad
  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

  • 72 Answers

SOURCE: Need directions for replacing a hub bearing

REMOVE BRAKES, ON BACK SIDE OF SPINDLE REMOVE FOUR RETAINING BOLTS AND HUB ASSEMBLY SHOULD COME OFF.. MAY HAVE TO TAP WITH A HAMMER TO BREAK FREE FROM THE SPINDLE... BE SURE TO THOUOUGHLY CLEAN THE SPINDLE BEFORE INSTALLING NEW BEARING ASSEMBLY.

Posted on May 09, 2009

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

  • 186 Answers

SOURCE: NEED TO REPLACE WHEEL HUB BEARING OR ONLY THE BEARING

Front Is pressed into hub & knuckle.Rear is a Hub/Bearing Assembly held in by 4 10mm bolts.Will need to pound out with hammer in rear after bolts come out,lots of rust holding them in.Front Knuckle has to come off,Then a large Snap ring,then press out the hub,then the wheel bearing.Hope this helps

Posted on May 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

2008 siverado. Front-end humming. Sounds like extremely loud tire pattern noise coming from left-front wheel area, noise stops when i turn the steering wheel to the right. replaced tire with no results.


it is your wheel bearing. the bearing is a sealed unit so you replace the hub assembly. remove wheel,caliper,brake rotor.if it is 4x4 loosen axle nut. there are three 15mm bolts on back side of spindle remove these and slide hub out replace with new one. most hubs come with new wheel speed sensor so remove harness from connectors or if no new one remove the screw holding it in place to hub and slide out.

Dec 31, 2010 | 2008 Chevrolet Silverado 1500

1 Answer

Abs activates just before truck stops (2005 chevy silverado) wheels not skidding, assuming a wheel sensor is bad, how do find out which one, or is the problem in the abs computer, abs light does not come...


This is a condition known as over active ABS. GM has a technical service bulletin for this. Basically what it say is to remove the front wheel speed sensors from the hubs, clean the mating surface between the sensor and the hub, apply some di-electric grease over the cleaned area, and reinstall the sensor.

You can try this on the front sensors and see if the problem goes away. I will warn you that you need to be very careful removing the sensor from the hub as they can break off. If it breaks off in the hub you will need to replace the hub and bearing.

You can also check to see if one of the front wheel bearings is loose. with the tire off the ground grab the tire at the 12 and 6 position and push/pull. if the wheel moves and you can see the rotor moving also than the wheel bearing may be sloppy enough for internal exciter ring to get an excessive gap from the abs sensor.

The easiest thing to do is look at wheel speed data on a higher end scan tool. When the symptom happens you will see the wheel speed drop out. Whatever wheel drops out is the wheel that needs to be checked.

Hope that helps.

Oct 01, 2010 | 2005 Chevrolet Silverado

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

Location of speed sensor for 1998 silverado


You need to know which one to replace. They are located on the front wheel bearing hub assembly on the backside, by the brake caliper. It is held in place by one screw and the wire just unplugs. Rocks damage these and they quit. Hope this helps.

Jun 11, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

2004 silverado 4x4 2500 left front wheel bearing


  1. Raise and support the vehicle.
  2. Remove or disconnect the following:

    Tire and wheel assembly Caliper and rotor Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle Electrical connection for the wheel speed sensor Front drive halfshaft assembly on four wheel drive models Hub and bearing assembly mounting bolts Hub and bearing assembly O-ring seal from the steering knuckle bore (2500 series)
  3. Clean and inspect the O-ring seal
To install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly.
  2. Install the O-ring to the steering knuckle (2500 series).
  3. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent.
  4. Install or connect the following:

    Hub and bearing assembly Hub and bearing assembly mounting bolts. Tighten the bolts to 133 ft. lbs. (180 Nm). Front drive halfshaft assembly on four wheel drive models Electrical connection for the wheel speed sensor Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle. Tighten to 106 inch lbs. (12 Nm). Rotor Tire and wheel assembly.
You can go to autozone.com and register for free online repair manual with everything you need.

Jan 19, 2010 | 2004 Chevrolet Silverado 2500 Crew Cab

1 Answer

How do you remove the backing plate from an '05 Chev Venture rear hub so the hub can be replaced?


The 4 Bolts that Hold the HUB in Also Hold the Backing Plate
Hub Replacement - Rear (Front Wheel Drive/Drum)

Removal Procedure
  1. Raise and support the vehicle.
  2. Remove the tire and wheel.
  3. Remove the brake drum.
    1. Remove and DISCARD the wheel bearing/hub bolts.
    2. Remove the wheel bearing/hub.
    3. Disconnect the wheel speed sensor electrical connector (2).Installation Procedure
    4. Connect the wheel speed sensor electrical connector (2).
      1. Install the wheel bearing/hub. Caution: These fasteners MUST be replaced with new fasteners anytime they become loose or are removed. Failure to replace these fasteners after they become loose or are removed may cause loss of vehicle control and personal injury. Notice: Refer to Fastener Notice in Service Precautions.
      2. Install the NEW wheel bearing/hub bolts.
      1. Install the brake drum.
      2. Install the tire and wheel.
      3. Lower the vehicle.

Nov 07, 2009 | 2005 Chevrolet Venture

2 Answers

Where wheel speed sensor is located on 2001 pontiac grand am se


2001 Pontiac Grand Am 2.4L SFI DOHC 4cyl

Vehicle Speed Sensor - Location:
The speed sensors are built right into the wheel bearings of your vehicle, at the front and rear locations. They work both with the anti-lock brakes and with the traction control systems on the vehicle.

Removal & Installation
Front
The front wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Front Suspension for service procedures.
Rear
The rear wheel speed sensor is part of the hub/bearing assembly. Refer to Wheel Hub and Bearing Replacement in Rear Suspension for service procedures.

I hope help you with this (remember rated this help) Have a nice day, good luck.

Sep 23, 2009 | 2001 Pontiac Grand Am SE

1 Answer

Why?


ABS activation at low speeds, .

Cause
The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface.

Correction
Measure AC voltage and clean the wheel speed sensor mounting surfaces.

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in the General Information sub-section of the Service Manual (SI Document ID #899664).
Disconnect both the front wheel speed sensor (WSS) connectors at the frame and harness.
Place a Digital Volt Meter (DVM) across the terminals of each WSS connector.
Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV's. If the reading is less than 350 ACmV's, remove the wheel speed sensor. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual. Plug the WSS bore in order to prevent debris from falling into the hub during service.
Clean the WSS mounting surface on the hub to remove any rust or corrosion using a wire brush, or equivalent.

Important
Make sure that the sensor sits flat on the hub. Check the sensor flange against a straight edge to ensure flatness. If the sensor flange is distorted, replace the sensor.


Apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (Canadian P/N 993037).
Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual.
Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV's.

Aug 26, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Antilock brake system engages on low speed stops on dry pavement on my 2004 Silverado.


The most likely cause is rust buildup under wheel speed sensors causing them to dislodge(lift up) from front hubs and read incorrectly. If recall has been performed to fix this problem...You may have to replace the appropriate hub in order to stop the ABS activation at low speeds. Let me know if i can help more.

Nov 03, 2008 | 2004 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...