Question about Nissan Altima

Open Question

Differential pressure feedback egr circuit low input

Check engine

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Molson02536
  • 3854 Answers

SOURCE: 1998 PONTIAC SUNFIRE ADVISE

Exhaust Gas Recirculation System Is the main problem here. the other code P0118 may be a bad temprature sensor or your thermostate needs to be changed. Last it could be a weak water pump. 

So what is an EGR system and how does it work? EGR stands for Exhaust Gas Recirculation, and as its name implies, this system allows exhaust gasses from your car to be re-circulated into the engine, helping to reduce emissions. These systems are mostly comprised of the EGR valve, a DPFE (Delta Pressure Feedback EGR) sensor, hoses, a vacuum regulator, some vacuum lines, wiring, the computer and the exhaust tube leading to the valve itself. 
The car's wiring can be tested in the normal fashion by looking for broken and lose wire, and all vacuum lines can be checked easily for cracks, leaks and correct routing.
The last thing i would then check is the the EGR valve, EGR vacuum regulator and DPFE sensor (or similar flow sensor).
I hope this helps and good luck

Posted on Apr 09, 2009

csmock132
  • 4669 Answers

SOURCE: DPFE EGR Pressure Feedback Sensor Issue - 2001 Mercury Sable

The DPFE sensor is a very common failure on all Ford models. Just have the sensor replaced. Or do it yourself. It is very easy to change you can do it in 10 minutes.

Posted on May 20, 2009

66 chrgr
  • 1011 Answers

SOURCE: problem with my vehicle

You need to replace the dpfe sensor this will fix it.

Posted on Jun 21, 2009

  • 14036 Answers

SOURCE: I had two problems posted for my Ford Explorer

CODE PO455 EVAPORATIVE EMISSION CONTROL SYSTEM LEAK DETECTED.POSSIBLE CAUSE - CANISTER VENT SOLENOID STUCK OPEN OR.FUEL TANK PRESSURE SENSOR HAS FAILED MECHANICALLY.OR BAD FUEL CAP. CODE PO1400 -DIFFERENTIAL PRESSURE FEED BACK EGR SENSOR CIRCUIT LOW VOLTAGE DETECTED.POSSIBLE CAUSE -DPF EGR SIGNAL CIRCUIT SHORTED TO GROUND OR DPF EGR SIGNAL VREF CIRCUIT OPEN OR DPF EGR SENSOR IS DAMAGED OR HAS FAILED.I WOULD HAVE GARAGE OR DEALERSHIP TO USE THEIR DIAGNOSTIC EQUIPMENT TO CHECK OUT YOUR EMISSION CONTROL SYSTEM.AND EGR VALVE BECAUSE PARTS IS TOO EXPENSIVE TO BUY.IF YOU DONT NEED THEM.SEE YOU CAN REPLACE THE DPF EGR SENSOR AND THE CANISTER VENT SOLENOID.BUT IT COULD BE A LEAKING GAS CAP OR SOMETHING ELSE.SO LET GARAGE CHECK IT OUT.TO BE ON SAFE SIDE.NOW YOU CAN BUY THOSE 2 SENSORS AND IT COULD FIX YOUR RIDE.I KNOW MONEY IS TIGHT ECONOMY IS IN BAD SHAPE.

Posted on Aug 26, 2009

ronaldo_ross
  • 1056 Answers

SOURCE: engine light on 2002 Explorer. engine code P1400

This may have to do with a bad wiring. Check all the wiring associated with EGR operation. Whenever a computer throws a code about high or low circuit voltage, it is usually attributed to abnormal wiring.

Posted on Nov 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Code p1400 gmc enjoy 2007 what is the problem in this code


Definition of Diagnostic Trouble Code P1400 Audi: EGR Valve Circ Electrical Malfunction BMW: Heated Catalyst Battery Voltage or Current too Low during Heating (Bank 1) Chrysler: Manifold Differential Pressure Sensor Circuit Malfunction Dodge: Manifold Differential Pressure Sensor Circuit Malfunction Ford: Differential Pressure Feedback EGR Circuit Low Input Hyundai: EGR System Monitor Malfunction Infiniti: EGRC Solenoid/V Jaguar: Exhaust Gas Recirculation Valve Position Control Jeep: Manifold Differential Pressure Sensor Circuit Malfunction Lexus: Sub-TPS Malfunction Lincoln: Differential Pressure Feedback EGR Circuit Low Input Mazda: DPFE Sensor Circuit Low Input Mercedes: EGR Switchover Valve Malfunction (C230 Only) Mercury: Differential Pressure Feedback EGR Circuit Low Input Mitsubishi: Manifold Differential Pressure Sensor Circuit Malfunction Nissan: Differential Pressure Feedback EGR Circuit Low Input Subaru: Fuel Tank Pressure Control Solenoid Circuit Low Input Toyota: Sub-Throttle Position Sensor Malfunction Volkswagen: EGR Valve Circ Electrical Malfunction

Jun 20, 2015 | 2007 GMC Envoy Denali

1 Answer

What are the probable cause(s) of DTC P1406?


Definition of Diagnostic Trouble Code P1406 Audi: EGR Temperature Sensor Range/Performance BMW: Heated Catalyst Internal Control Module Checksum/ROM Error Buick: EGR Valve Pintle Position Circuit Cadillac: EGR Valve Pintle Position Circuit Chevrolet: EGR Valve Pintle Position Circuit Ford: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged GMC: EGR Valve Pintle Position Circuit Isuzu: EGR Valve Pintle Position Circuit Lincoln: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged Mazda: DPFE Sensor Downstream Hose Off Or Plugged Mercury: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged Oldsmobile: EGR Valve Pintle Position Circuit Pontiac: EGR Valve Pintle Position Circuit Saturn: EGR Valve Pintle Position Circuit Toyota: Turbo Pressure Sensor Range/Performance Problem Volkswagen: EGR Temperature Sensor Range/Performance Volvo: Termperature Warning > 100 degrees C

Jun 18, 2015 | Cars & Trucks

1 Answer

1401 egr code


P1401 FORD - DPFE Sensor Circuit High
Faulty Differential Pressure Feedback Electronic (DPFE) sensor
- Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
- Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection. This is not likely the EGR but the EGR pressure sensing valve.

Oct 19, 2012 | Cars & Trucks

2 Answers

Need to find and replace the DPFE-15 sensor. Dealership diagnosed when service engine light came on and saaid this is what needed replacing. Problem is I do not know where to find it on the engine.


Exhaust Gas Recirculation (EGR) System The exhaust gas recirculation (EGR) system is designed to:
  • reintroduce exhaust gas into the combustion cycle.
  • lower combustion temperatures.
  • reduce the formation of oxides or nitrogen (NOX).
The amount of exhaust gas reintroduced and the timing of the cycle varies by calibration. Timing and volume are controlled by the following:
  • engine rpm
  • engine vacuum
  • exhaust system back pressure
  • engine coolant temperature
  • air charge temperature
  • throttle position
The EGR valve (EGR valve) (9D475) is vacuum-actuated. The vacuum hose routing diagram is shown on the Vehicle Emission Control Information (VECI) decal. The EGR system is a differential pressure feedback EGR Sensor system. Differential pressure feedback EGR Sensor is a subsonic closed loop EGR system. The differential pressure feedback EGR system:
  • monitors EGR flow rate by the pressure drop across the metering orifice located in the EGR tube.
  • uses a differential pressure feedback EGR sensor as the feedback device.
  • uses the EGR valve only as a pressure regulator, rather than a flow metering device.
  • controlled pressure is varied by the valve movement using vacuum output of the EGR vacuum regulator solenoid (9J459).
  • allows for a more accurate assessment of EGR flow requirements.


Differential Pressure Feedback EGR Flow Diagram


aa3104a.gif

Differential Pressure Feedback EGR Sensor Removal
  1. Disconnect engine control sensor wiring (12A581) from Differential Pressure Feedback EGR Sensor.
  1. Disconnect Differential Pressure Feedback EGR Sensor hoses from EGR valve to exhaust manifold tube (9D477).
  1. Remove retaining nuts or bolts (depending upon application) and EGR Differential Pressure Feedback transducer.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten retaining nuts or bolts (depending upon application) to 5-7 Nm (45-61 lb-in).


    Differential Pressure Feedback EGR Sensor, 3.0L (2V) Engine


    aa0036a.gif



    Differential Pressure Feedback EGR Sensor, 3.0L (4V) Engine


    a23840a.gif


    Item Part Number Description 1 6049 RH Cylinder Head 2 - Differential Pressure Feedback EGR Sensor 3 - Nut (2 Req'd) 4 - Stud Bolt 5 - Bolt (2 Req'd) 6 - Differential Pressure Feedback EGR Sensor Bracket A - Tighten to 5-7 Nm (45-61 Lb-In) B - Tighten to 8-12 Nm (71-106 Lb-In)

    Engine Emission Control Component Location-3.4L SHO Engine


    a25013a.gif


    Item Part Number Description 1 95607-05200 Nut 2 - EGR Sensor Hose 3 - EGR Sensor Hose 4 95027-08016 Bolt 5 - Differential Pressure Feedback EGR Sensor 6 9J433 Differential Pressure Feedback EGR Sensor Mounting Bracket 7 9D474 EGR Solenoid Vacuum Valve (2 Req'd) 8 A4670 Vacuum Tube Assembly 9 9424 Intake Manifold 10 9J459 EGR Vacuum Regulator Solenoid A - Tighten to 5-7 Nm (45-61 Lb-In)
Hope this helps

Aug 14, 2011 | 1999 Ford Taurus

3 Answers

My 2002 Ford Explorer gave me code P1400. What does it mean


P1400 indicates the following:
Differential Pressure Feedback Electronic Sensor circuit Low Voltage

Most common cause is a bad DPFE sensor.

Jul 15, 2011 | 2002 Ford Explorer

2 Answers

The fuel pressure is low and it wont move the code that it gave me was po1401 what does that mean


CODE P1401 IS SENSOR CIRCUIT HIGH INPUT. POSSIBLE CAUSES DPFE SENSOR SIGNAL CIRCUIT IS OPEN.DPFE SENSOR GROUND CIRCUIT IS OPEN.DPFE SENSOR SIGNAL IS SHORTED TO VREF 5V. DPFE SENSOR IS DAMAGED OR IT HAS FAILED. PCM HAS FAILED.******* WHEN YOU SEE CODE P1401 FLASHING ********** WHAT IS HAPPENING ENGINE RUNNING AND THE PCM DETECTED THE DPF EGR SENSOR SIGNAL WAS MORE THAN THE MAXIMUM CALIBRATED VALUE OF 4.5 VOLTS. ON THIS VECHICLE APPLICATION THE DPPE EGR VALVE AND EVR SOLENOID ARE INTEGRATED INTO THE ESM ASSEMBLY.

Jun 05, 2011 | 2001 Ford Expedition

2 Answers

My code reader says p1401 ford exscape


p 1401 is a code for differential pressure feedback egr circuit high input there is a small square sensor on the engine with a vacuum line here is some info Exhaust Gas Recirculation (EGR) System Monitor” Differential Pressure Feedback EGR
The Differential Pressure Feedback EGR System Monitor is an on-board strategy designed to test the integrity and flow characteristics of the EGR system. The monitor is activated during EGR system operation and after certain base engine conditions are satisfied. Input from the ECT, IAT, TP and CKP sensors is required to activate the EGR System Monitor. Once activated, the EGR System Monitor will perform each of the tests described below during the engine modes and conditions indicated. Some of the EGR System Monitor tests are also performed during on demand self-test.

The Differential Pressure Feedback EGR sensor and circuit are continuously tested for opens and shorts. The monitor looks for the Differential Pressure Feedback EGR circuit voltage to exceed the maximum or minimum allowable limits.

The DTCs associated with this test are DTCs P1400 and P1401.
The EGR Vacuum Regulator solenoid is continuously tested for opens and shorts. The monitor looks for an EGR Vacuum Regulator circuit voltage that is inconsistent with the EGR Vacuum Regulator circuit commanded output state.

Jul 26, 2010 | 2001 Ford Escape

3 Answers

Wat does code p1400 means


In order to give you accurate information. I need size of engine example 2.0 L 3.0L. but code P1400 means Differential Pressure feedback EGR circuit low input. Maybe your differential oil is low.

Apr 01, 2010 | 2002 Ford Taurus

1 Answer

I had two problems posted for my Ford Explorer 1998 P1400 Differential Press Feedback EGR Circuit low input Po455 Mod $10 3/4 EVAP EMISSION CONTROL SYSTEM LEAK (LARGE) How can I fix it and how can I go...


CODE PO455 EVAPORATIVE EMISSION CONTROL SYSTEM LEAK DETECTED.POSSIBLE CAUSE - CANISTER VENT SOLENOID STUCK OPEN OR.FUEL TANK PRESSURE SENSOR HAS FAILED MECHANICALLY.OR BAD FUEL CAP. CODE PO1400 -DIFFERENTIAL PRESSURE FEED BACK EGR SENSOR CIRCUIT LOW VOLTAGE DETECTED.POSSIBLE CAUSE -DPF EGR SIGNAL CIRCUIT SHORTED TO GROUND OR DPF EGR SIGNAL VREF CIRCUIT OPEN OR DPF EGR SENSOR IS DAMAGED OR HAS FAILED.I WOULD HAVE GARAGE OR DEALERSHIP TO USE THEIR DIAGNOSTIC EQUIPMENT TO CHECK OUT YOUR EMISSION CONTROL SYSTEM.AND EGR VALVE BECAUSE PARTS IS TOO EXPENSIVE TO BUY.IF YOU DONT NEED THEM.SEE YOU CAN REPLACE THE DPF EGR SENSOR AND THE CANISTER VENT SOLENOID.BUT IT COULD BE A LEAKING GAS CAP OR SOMETHING ELSE.SO LET GARAGE CHECK IT OUT.TO BE ON SAFE SIDE.NOW YOU CAN BUY THOSE 2 SENSORS AND IT COULD FIX YOUR RIDE.I KNOW MONEY IS TIGHT ECONOMY IS IN BAD SHAPE.

Aug 26, 2009 | Ford Explorer Cars & Trucks

1 Answer

Egr vacuum solenoid


Exhaust Gas Recirculation (EGR) System Monitor—Differential Pressure Feedback EGR The Differential Pressure Feedback EGR System Monitor is an on-board strategy designed to test the integrity and flow characteristics of the EGR system. The monitor is activated during EGR system operation and after certain base engine conditions are satisfied. Input from the ECT, CHT, IAT, TP and CKP sensors is required to activate the EGR System Monitor. Once activated, the EGR System Monitor will perform each of the tests described below during the engine modes and conditions indicated. Some of the EGR System Monitor tests are also performed during on demand self-test.
  1. The differential pressure feedback EGR sensor and circuit are continuously tested for opens and shorts. The monitor looks for the Differential Pressure Feedback EGR circuit voltage to exceed the maximum or minimum allowable limits.

    The DTCs associated with this test are DTCs P1400 and P1401.
  1. The EGR vacuum regulator solenoid is continuously tested for opens and shorts. The monitor looks for an EGR Vacuum Regulator circuit voltage that is inconsistent with the EGR Vacuum Regulator circuit commanded output state.

    The DTC associated with this test is DTC P1409.
  1. The test for a stuck open EGR valve or EGR flow at idle is continuously performed whenever at idle (TP sensor indicating closed throttle). The monitor compares the Differential Pressure Feedback EGR circuit voltage at idle to the Differential Pressure Feedback EGR circuit voltage stored during key on engine off to determine if EGR flow is present at idle.

    The DTC associated with this test is DTC P0402.
  1. The differential pressure feedback EGR sensor upstream hose is tested once per drive cycle for disconnect and plugging. The test is performed with EGR valve closed and during a period of acceleration. The PCM will momentarily command the EGR valve closed. The monitor looks for the differential pressure feedback EGR sensor voltage to be inconsistent for a no flow voltage. A voltage increase or decrease during acceleration while the EGR valve is closed may indicate a fault with the signal hose during this test.

    The DTC associated with this test is DTC P1405.
  1. The EGR flow rate test is performed during a steady state when engine speed and load are moderate and EGR vacuum regulator duty cycle is high. The monitor compares the actual Differential Pressure Feedback EGR circuit voltage to a desired EGR flow voltage for that state to determine if EGR flow rate is acceptable or insufficient. This is a system test and may trigger a DTC for any fault causing the EGR system to fail.

    The DTC associated with this test is DTC P0401. DTC P1408 is similar to P0401 but performed during KOER Self-Test conditions.
  1. The MIL is activated after one of the above tests fails on two consecutive drive cycles.
0a01005.gif EGR Vacuum Regulator Solenoid The EGR vacuum regulator solenoid (Figure 88) is an electromagnetic device which is used to regulate the vacuum supply to the EGR valve. The solenoid contains a coil which magnetically controls the position of a disc to regulate the vacuum. As the duty cycle to the coil increases, the vacuum signal passed through the solenoid to the EGR valve also increases. Vacuum not directed to the EGR valve is vented through the solenoid vent to atmosphere. Note that at 0% duty cycle (no electrical signal applied), the EGR vacuum regulator solenoid allows some vacuum to pass, but not enough to open the EGR valve.

213d442.gif
Exhaust Gas Recirculation (EGR) Vacuum Regulator Solenoid Removal and Installation
  1. Disconnect the battery ground cable (14301). For additional information, refer to Section 414-01 .
  1. Disconnect the vacuum hoses and the EVR solenoid electrical connector.
  1. Remove the two nuts and the EVR solenoid (9J459).
From the looks of the rubber mounting, I would say it's mounted on the cowl (firewall) on the passenger side in the engine compartment.

Please rate as fixya if this helps. Thanks

Feb 24, 2009 | 2001 Ford Escort ZX2

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...