Question about Cars & Trucks

Open Question

Cap Fm 504 multi purpose bench

Product did not come with assembly instructions

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a fuse that makes the speedometer work on a 1996 dodge ram 1500 with a 3.9


Under the hood there is a relay center. It'll say Powertrain Control Module on the front - a black box with a lid - on the underside of that cap should be a map of the relays. On most of the 95 models it was relay #47. More than likely a lot hadn't changed in one model year. If you take a look at the map you want to check the relay for the Vehicle Speed Sensor - not Vehicle Speed Control - Control will be for cruise. If you have the relay identified, look around for something non-vital, like a horn for instance or turn signals and you can swap them out if they match. You'll see a few different types of relays usually - and all you have to do is match the numbers to the one you're unsure about. Unplug it. Plug the new one in and give it a test. If you're familiar with a multi-meter I could forward the instructions on bench testing the relay if you need it.


fuse-makes-speedometer-work-1996-dodge-4n3y21cmsqpgtsjshk50qfrx-3-0.png

All The Best, Justin Lee
17 South Industries, LLC

May 05, 2016 | Dodge Cars & Trucks

1 Answer

How to fit an upgrade armrest on an x type jag?


The center arm rest is attached to the console by 2 small Hex cap screws. The arm rest and intermediate slide panel are attached to the same hinge assembly with rivets.
to replace the upper arm rest, 1st remove the assembly from the console by removing the 2 hex screws this will allow you to work outside of the vehicle on a work bench. 3 rivets hold the arm rest to the hinge. You will need to drill out the rivets using a 1/8" drill bit. and install the replacement arm rest using new 1/8" pop rivets.
see illustration

section-ai1d4ga3barerea5mewg0gzj-4-0.jpg

Feb 07, 2015 | Jaguar X-Type Cars & Trucks

2 Answers

How do you take the seatbelts off of the middle bench seat on 2001 ford windstar so I can totally remove the seat for hauling purposes? 3rd bench seat is already out.


There's actually a small red button you can easily press with a flat head screwdriver or a penny located at the point where the end of the belt attaches to the seat
/uploads/images/seatbelts-off-middle-34923186-4-1.jpg

Jun 26, 2014 | Cars & Trucks

1 Answer

I have lost a fuel cap for my 1992 peugeot 405, will caps of other makes fit it?


We have no way to look this up. Please contact a local parts store.

Sep 28, 2012 | 1983 Peugeot 504

1 Answer

To start with my power steering pump was making a little noise and also had bubbles in the resevoir so i put a new power steering pump on it.not a rebuilt one. when i started it up i still have the bubbles...


Section 11-00: Steering System-Service 1999 Taurus, Sable Workshop Manual SERVICE PROCEDURES Purging Power Steering System of Air NOTE: If the air is not purged from the power steering system correctly, a second customer concern or pump failure could result. This condition can only occur on pre-delivery vehicles with evidence of aerated fluid or vehicles that have had steering component repair.

A whine noise heard from the power steering pump may be caused by air in the system. The following procedure must be performed whenever any of the following are performed:
  • All power steering noise complaints with evidence of aerated fluid on pre-delivery vehicles only, prior to any component repair.
  • After any power steering system component (for example, gear or hose) has been replaced and the noise is heard.
Fluid Level Top-Off Procedure
  1. Check and fill pump reservoir to dipstick full cold or remote reservoir center mark.
  1. Disable ignition by removing Fuse 10 in the fuse junction panel.
  1. Crank engine 30 seconds, check fluid level and add if required.
  1. NOTE: Do not hold steering wheel on stops.

    Crank engine 30 seconds while cycling the steering wheel lock to lock.
  1. Check fluid level and add fluid if required.
Air Purge with Vacuum External Source Procedure - 3.0L (2V) Engine, Flex Fuel and 3.4L SHO Engine
  1. Tightly insert the rubber stopper of the air evacuator assembly into pump reservoir.
  1. Reinstall Fuse 10 used to disable ignition and start vehicle.
  1. Apply 20-25 in-Hg (85-88 kPa) maximum vacuum for minimum of three minutes at idle; maintain maximum vacuum with vacuum source.
  1. Release vacuum and remove vacuum source.
  1. Add fluid to full warm or reservoir center mark.
  1. Reinstall vacuum source and apply 20-25 in-Hg (85-88 kPa) vacuum.
  1. NOTE: Do not hold steering wheel on stops.

    Cycle steering wheel from lock to lock every 30 seconds for approximately 5 minutes.
  1. Shut engine off, release vacuum and remove vacuum source.
  1. Add Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid if necessary and install dipstick or reservoir cap.
  1. NOTE: Do not hold steering wheel on stops.

    Start engine and cycle steering wheel from lock to lock every 30 seconds for approximately 5 minutes.
  1. Check for oil leaks at all connections.
  1. In severe cases it may be necessary to repeat air purge with vacuum source procedure.
Air Purge with Vacuum External Source Procedure - 3.0L (2V) and 3.0L (4V)
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to approximately 2.5 cm (1 in) (make a mark) above the top of the supply line.
  1. Tightly insert the rubber stopper of the air evacuator assembly into the pump reservoir.
  1. Apply 85-88 kPa (20-25 in-Hg) maximum vacuum for a minimum of three minutes.
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent until the level is at the marked point.
  1. Repeat Steps 3 and 4 until the fluid level stabilizes.
  1. Check reservoir level and add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to the FULL WARM (MAX) mark.
  1. Install the number 10 fuse in the fuse junction panel. Start the engine.
  1. NOTE: The front wheels must be off the floor during lock-to-lock rotation of the steering wheel.

    NOTE: Do not hold the steering wheel on stops.

    Reinstall the vacuum source and apply 85-88 kPa (20-25 in-Hg) maximum vacuum and cycle the steering wheel from lock-to-lock every thirty seconds for a minimum of 5 minutes.
  1. Shut the engine off, release the vacuum and remove the vacuum source.
  1. Add Motorcraft MERCON® Multi-purpose (ATF) Transmission Fluid XT-2-QDX or MERCON® equivalent to the FULL WARM (MAX) level. Install the dipstick or reservoir cap.
  1. NOTE: Do not hold the steering wheel on stops.

    NOTE: In severe cases, it may be necessary to repeat air purge with vacuum source procedure.

    Start the engine and cycle the steering wheel from lock-to-lock every thirty seconds for approximately five minutes.
  1. Lower the vehicle front end.
  1. Check for oil leaks at all connections.

Jul 24, 2011 | 1999 Ford Taurus

1 Answer

Blower motor fan not working .What is the fuse labeled as (were all the fuses are)


There are two fuses associated with the blower motor. Fuse #1 MULTI-PURPOSE 25A is the blower motor fuse, and fuse #15 MULTI-PURPOSE 10A is the blower motor relay switch fuse.

Feb 19, 2011 | 1994 Eagle Summit

1 Answer

Torque specs for 1993 7.3L diesel injector



please rate, thanks

Installation
  1. Thoroughly clean nozzle bore in cylinder head before reinserting nozzle assembly with Nozzle Seat Cleaner T83T-9527-A. Pay particular attention to seating surface, in order that no small particles of metal or carbon will cause assembly to be cocked or permit blow-by of combustion gases. Blow out particles with compressed air.

    a119091a.gif

  1. Remove protective cap and install a new copper gasket on nozzle assembly with a small dab of Multi-Purpose Grease D0AZ-19584-AA (ESR-M1C159-A) or equivalent. NOTE: Anti-seize compound or equivalent should be used on nozzle threads to aid installation and future removal.
    ani_caut.gif CAUTION: Be careful that nozzle tip does not strike against recess wall.
  1. Install nozzle assembly into cylinder head nozzle bore.
  1. Tighten nozzle assembly to 47 Nm (35 ft-lb).
  1. Remove protective caps from nozzle assemblies and fuel lines.
  1. Install leak-off tees and lines as an assembly by lowering onto nozzles. Connect clip and hose to fuel return elbow at pump. Install line to retaining clamps. NOTE: Install two new O-ring seals for each fuel return tee.
  1. Connect high pressure fuel line(s) and tighten to specification using Fuel Line Nut Wrench T83T-9396-A.
  1. Start engine.
  1. If necessary, purge high-pressure fuel lines of air by loosening connector one-half to one turn and cranking engine until bubble-free fuel flows from connection. ani_caut.gif WARNING: KEEP EYES AND HANDS AWAY FROM FUEL SPRAY. FUEL SPRAYING FROM PARTIALLY OPENED CONNECTION UNDER HIGH PRESSURE CAN PENETRATE THE SKIN AND CAUSE INFECTION. MEDICAL ATTENTION SHOULD BE PROVIDED IMMEDIATELY IN THE EVENT OF SKIN PENETRATION.
  1. Check for fuel leakage at high-pressure connections.

Nov 17, 2010 | 1993 Ford F350

1 Answer

Back passenger door wont lock i have central locking other doors ok


Go buy a multi purpose lubricant and spray it into the inside door handle. I used permatex ultra slick synthetic multi purpose lubricant. It costs $8.

Feb 14, 2010 | 2005 Ford Focus

2 Answers

1998 S10 rear break lights and blinkers do not work.


If the fuses or brake light switch were bad your third brake light would not work same with the multi purpose switch. you either have a wiring problem like some broken wires or the actual light sockets are bad. it is common with gm trucks that the circuit board for the tail lights melts and does not make contact.

Nov 02, 2009 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...