Question about 1994 Ford Aspire

Open Question

Hey Dennis, Im having a problem with my 1994 Ford Aspire, The turn signals quit working. My 4 way flashers work the stop tail work, the hi-low headlights work. Is there a fuse or relay for the turn signals

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Benimur
  • 6966 Answers

SOURCE: 1991 Ford E150 turn signals do not work,emergancy flashers flash constantlly unless the flasher relay is unplugged from fuse block

Hi,

If I understand you right based on your post/description, the signal lights would still turn on even if any or both of the flasher relays are removed. Should this be the case, then the signal lights are not getting the power from the flasher relays but from the brake light circuit.

Perhaps your concern is not with any of the flasher, but simply missing or loose ground more particularly with the rear lights. Perhaps you could try determining which of the wires for the brake lights and signal lights (as they come out of the light assembly) would be ground . A test and even possibly a temporary workaround is to hard wire a second ground connection from the determined ground wire of the lights and attach it to any conveniently located bolt or screw to the body. it may be to your advantage to do this on all the rear lights assembly.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Posted on Aug 05, 2008

Ad
  • 4369 Answers

SOURCE: 2003 F-250 Flashers won't work

I'm leaning towards a bad multifunction switch on your steering column.

symptom chart

  • The turn signal lamps are never on
  • Central junction box (CJB) fuse 27 (15A).
  • Circuitry.
  • Electronic flasher.
  • Multifunction switch.
  • CJB.
  • Go To Pinpoint Test K .



  • The hazard lamps are inoperative
  • Central junction box (CJB) fuse 18 (20A).
  • Circuitry.
  • Electronic flasher.
  • Multifunction switch.
  • CJB.
  • Go To Pinpoint Test M .


Multifunction Switch Removal and Installation
  1. Remove the ignition switch lock cylinder.
    1. Insert the ignition key into the lock cylinder and turn to the RUN position.
    1. Push the ignition switch lock cylinder release tab with a punch while pulling out the ignition switch lock cylinder.
ac0c6df.gif
  1. If equipped, twist the tilt wheel handle and shank and remove.
dbfa19d.gif
  1. Remove the upper and lower steering column shrouds.
    1. Remove the screws.
    1. Remove the upper and lower steering column shrouds.
26d3c78.gif
  1. Remove the multifunction switch.
    1. Remove the screws.
    1. Disconnect the electrical connectors.
    1. Remove the multifunction switch.
bd46c8c.gif
  1. To install, reverse the removal procedure.
You can do this. You don't even have to remove the steering wheel.
Buy the part at tascafordparts.com for about 35% off too.

Please rate as fixya if this fixes your issue and report back on success. good luck.


Posted on Mar 05, 2009

  • 24 Answers

SOURCE: no turn signals but flashers work

You may have two relays one for hazards and one for turn indicators.

Posted on May 31, 2009

  • 63 Answers

SOURCE: My 96 ranger turn signals & hazards don't

It Could Be The Flasher Switch Or Turn Signal Switch Now This May Not Be Whats Wrong with Yours Now My Ignition Switch came Apart on my car and i lost turn signals and E flashers i hope one of these will help

Posted on Aug 17, 2009

  • 130 Answers

SOURCE: no trailer turn signals tail lights work . you

If it is a factory trailer package then there are fuses for the left turn signal and the right turn signal for the trailer connector. Check your owners manual for the location of these two fuses.

Bob

Posted on Apr 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble shoot turn signals 1994 Ford Ranger 2.3 engine


Diane, There are 2 separate flashers on your vehicle, one is for the emergency/4 way lights and one flasher is for the signal lights. It may be worth the couple bucks and replacing the signal flasher as a first step. Recheck bulbs/sockets, fuses/relays, flasher. If all looks good possible signal switch is bad. Remove switch and try to clean contacts or replace switch. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
https://ca.answers.yahoo.com/question/index?qid=20090405174036AARb2Uc
1994 Ford Ranger Turn Signal Electrical Problem 1994 Ford Ranger
93 Ranger Turn Signal Problem Ford Truck Enthusiasts Forums

Aug 20, 2016 | 1994 Ford Ranger Supercab

1 Answer

The turn signals and hazards quit working on my 1993 ford escort wagon


Hazard lights are nearly perfect, turn signals come and go. Since both failed, it's not likely to be the flashers or switches. If the fuses are good, you have a rusted ground-20 years of rust! Check by jumping new ground wire to green wire. Wires sometimes break inside door jamb and body but not very often. The poor man's solution is to make a tail light with two sharp pins and three feet of wire, check wire at switch, flasher, and every three feet after that. Few people bother with automotive electrics for these reasons.

Jul 31, 2013 | 1994 Ford Escort

1 Answer

Turn signal not working


TAIL LIGHT NOT WORKING

It can be faulty tail light bulb or its issue with tail light control switch or its wiring's are short.

Check the voltage at fuse slot of tail light.Do you receive 12 volt there.If not,then it says tail light switch is not receiving power supply.


---------

There are few help links related to your problem.I suggest you refer the list and check the help links.Click the link below:-----




Turn Signal Not working

http://technoanswers.blogspot.com/2012/11/turn-signal-not-working.html

----------

Right turn signal not working on Pontiac Car?

http://schematicsdiagram.blogspot.com/2011/12/right-turn-signal-not-working-on.html

--------

Only one side indicator light working on car?

http://schematicsdiagram.blogspot.com/2011/12/only-one-side-indicator-light-working.html

-----------

Turn signals not working on 1987 Jeep Wagoneer?

http://schematicsdiagram.blogspot.com/2011/12/turn-signals-not-working-on-1987-jeep.html

-----------

SOLVE YOUR 4 WAY FLASHER RELATED PROBLEMS HERE

http://repairhelpcenter.blogspot.com/2012/11/4-way-flasherturn-signal-flashersignal.html

----------

1994 Toyota Camry: Bypass Tail light Relay Circuit?

http://whatisbyme.blogspot.in/2012/04/1994-toyota-camry-bypass-tail-light.html

-----------

2008 Toyota RAV4: Replace Tail light Lens Cover?


http://technoanswers.blogspot.in/2012/04/2008-toyota-rav4-replace-tail-light.html

--------

2003 Chevrolet S10 Tail light Fuse

http://schematicsdiagram.blogspot.com/2012/11/2003-chevrolet-s10-tail-light-fuse.html

---------

Chevrolet Parking light and Tail lamp light Wiring diagram

http://schematicsdiagram.blogspot.com/2012/11/chevrolet-parking-light-and-tail-lamp.html

----------

Car Tail Lights Not Working?

http://schematicsdiagram.blogspot.com/2011/12/car-tail-lights-not-working.html

----------

These details will help.

Thanks.

Feb 15, 2013 | 2004 Pontiac Grand Am

1 Answer

The tail lights do not work. The headlights, blinkers, and brake lights work. I checked the fuses and they are all good.


It can be faulty tail light bulb or its issue with tail light control switch or its wiring's are short.

Check the voltage at fuse slot of tail light.Do you receive 12 volt there.If not,then it says tail light switch is not receiving power supply.


---------
There are few help links related to your problem.I suggest you refer the list and check the help links.Click the link below:-----
1994 Toyota Camry: Bypass Tail light Relay Circuit? http://whatisbyme.blogspot.in/2012/04/1994-toyota-camry-bypass-tail-light.html

-----------
2008 Toyota RAV4: Replace Tail light Lens Cover?


http://technoanswers.blogspot.in/2012/04/2008-toyota-rav4-replace-tail-light.html
--------
2003 Chevrolet S10 Tail light Fuse http://schematicsdiagram.blogspot.com/2012/11/2003-chevrolet-s10-tail-light-fuse.html
--------- Chevrolet Parking light and Tail lamp light Wiring diagram http://schematicsdiagram.blogspot.com/2012/11/chevrolet-parking-light-and-tail-lamp.html
---------- Car Tail Lights Not Working?

http://schematicsdiagram.blogspot.com/2011/12/car-tail-lights-not-working.html

----------
Turn Signal Not working http://technoanswers.blogspot.com/2012/11/turn-signal-not-working.html
---------- Right turn signal not working on Pontiac Car?

http://schematicsdiagram.blogspot.com/2011/12/right-turn-signal-not-working-on.html

--------
Only one side indicator light working on car?

http://schematicsdiagram.blogspot.com/2011/12/only-one-side-indicator-light-working.html

-----------
Turn signals not working on 1987 Jeep Wagoneer? http://schematicsdiagram.blogspot.com/2011/12/turn-signals-not-working-on-1987-jeep.html

-----------

SOLVE YOUR 4 WAY FLASHER RELATED PROBLEMS HERE
http://repairhelpcenter.blogspot.com/2012/11/4-way-flasherturn-signal-flashersignal.html

----------
Thesedetails will help.
Thanks.

Nov 23, 2012 | Cars & Trucks

1 Answer

I have a 1994 ford ranger and the 4 way flashers and turn signals suddenly stopped working


Check the flasher . This is usually right at your fuse panel. It just plugs in and can be removed and installed very easy

Jun 28, 2010 | 1994 Ford Ranger Supercab

1 Answer

1994 Chevy truck. Turn signals do not work.


CHECK FUSE.IF GOOD YOU HAVE A BAD GROUND OR FAULTY TURN SIGNAL FLASHER.FLASHERS LOCATED ON THE INTERIOR FUSE RELAY BOX.

Sep 22, 2009 | Chevrolet 1500 Cars & Trucks

Not finding what you are looking for?
1994 Ford Aspire Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...