Question about 2002 Mercury Sable

1 Answer

Fuse for turnsignals - 2002 Mercury Sable

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Do u have an owners manual? look in the glossary it should tell u where all of your fuses are at. if not look on lft side of dash on the end where the door closes, should be a fuse cover there or under hood lft side fender well.

Posted on Feb 21, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2008 chevy impla and the left turnsignal fuse keep blowing every time i use the the left turnsignal ?


Sounds like a short in either the front or rear bulb, or a bad socket or even possibly a bulb installed backwards. Has anything been changed in either of these locations?

Feb 18, 2015 | Cars & Trucks

1 Answer

1987 ford ranger turn signals keep blowing fuses. have changed flasher fuse and switch on column. just keeps blowing?


first thing i guess to understand what is going on here ,is a little back to basics on how turnsignals work , first item you have is power fuse then it's off to flasher module than it goes to the turnsignal switch on colum ,of course anywhere on it way to there the power could got to ground and cause the fuse to trip, now the power depending on Left or right selection , is directed to lights on both front and back of truck,thankfully rangers don't have em on the side) now any place in this pathway the wire could go to ground and blow the fuse, now to troubleshoot and narrow down the area that fault is located , (1) replace fuse with correct size and ck for proper fit in fusebox and start and operate truck for a few minutes DO not use turnsignals, ck fuse is it still good if so go to step 2 if not stop and ck wire conditions in steering colum and switch(2) start truck and try right hand turn signal only verify lights working ,Ok yes/no if not replace fuse and try left side same way, Ok yes /no if right or left side only blows fuses take ALL bulbS OUT of lights and try again , if fuse still blows then look for wire fault on that side of truck if fuse is still good then look carefull at light bulb sockets for rust and powered corrosion (ill bet an 87 has some ) you may need to replace bulb sockets , they do sell em in autoparts stores .

Jun 30, 2014 | 1987 Ford Ranger

1 Answer

Turnsignals and blower on heat stopped working at


check the fuse links under the hood near the battery / starter area and also check the main plug into the firewall

Jan 20, 2010 | 2000 Dodge Caravan

2 Answers

Where is the turnsignal flasher located 1991 nissan sentra 4dr


In your fuse box should be a large 1-2" square box inside the fuse box. Or under the dash board .

Jul 09, 2009 | 1991 Nissan Sentra 2 Door

1 Answer

Turnsignals just stopped working.Hazards will not operate either.All fuses are good


There is a relay that controls this that needs to be replaced. Here is a link to the part:
http://www.bestvalueautoparts.com/item.wws?sku=7060&itempk=315698&mfr=WAGNER%20LIGHTING&weight=1

Jun 02, 2009 | 1992 Lexus Es 300

1 Answer

Where is the turnsignal flasher & hazard flasher on this jeep


I believe both are located on the fuse block, driver side of steering column.

Apr 22, 2009 | 1997 Jeep Grand Cherokee

1 Answer

I CHECKED THE TERMINAL AND THE FUSE MY TURNSIGNALS


Probably the flasher unit, it is under the top column cover (behind the steering wheel) and plugs into the multi-function switch. There are two phillips screws that hold the covers together, accessible from the bottom cover.

Buy one from the dealer only, as the aftermarket ones are junk and most don't work.

Apr 02, 2009 | 1997 Dodge Intrepid

2 Answers

No brake lights on 1995 lunina


check your fuses first, if none blown check the brake ligft switch.its located on the brake peddal assembly.

Aug 12, 2008 | 1995 Chevrolet Lumina

Not finding what you are looking for?
2002 Mercury Sable Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...