Question about 1992 Ford Tempo

Open Question

How to take the door panel off a 92 ford tempo

Door handle does not work

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: Door handle on 1998 Ford Ranger

Remove the door panel and on the inside of the door is a clip or a couple of nuts you'll need to remove. The door handle will fall out.

Posted on Jun 14, 2008

Ad
dgjtex
  • 405 Answers

SOURCE: door handles

You have to remove the inner door panels, remove all screws on inside some may be hidden under platic clip in pieces. after you remove them there will be a plastic sheet glued to door. pull this back and you will have access to the linkage, these clips can be purchaes at autoparts store or of course from the dealer. Hope this helps

Posted on Dec 15, 2008

michigan man
  • 3533 Answers

SOURCE: changing outside door handle drivers door

first disconnect the negative side of battery and then open the door and start looking for small black screws or nuts then remove you find some hidden behind what look like little doors that you will need to remove with a screw driver becareful not to pry the plastic completely out of the door panel itself because if this happens you will have to figure out a way to repair so the panel will stay on the door get a thin pry bar to this job or a butter knife

Posted on Jan 05, 2009

mohammed387
  • 1952 Answers

SOURCE: I have a 1993 Ford

remove the door panel and check to make sure the linkage to the lock assembly is still attached. I can't give an estimate because I don't know what is wrong at this point

are the locks manual or electric?i have seen most electric locks freeze up because of rust/.corrosion.the rubber accordian seal fails and moisture does it's job.there is no lubrication on the mechanism.it's basically a push pull magnet tube with a spiral grooved actuator rod.this is to assure no accidental vibration/jar induced movement.also means very difficult to budge when corroded.i have gotten a few to move by grabbing lock post with pliers and pulling hard.good luck!



Rear Door Window Regulator and Motor
Removal and Installation
Remove the rear door trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .
Remove the door mounted speaker.
Remove the watershield.
NOTE:The glass must be lowered for this step.

NOTE:Some vehicles may use rivets to attach the glass to the regulator.

Remove the bolt that attaches the glass to the regulator.
Raise and support the rear door window glass to the full up position.

NOTE:Do not detach the door handle from the latch cable during this step.

Remove the rear inside door handle.
Remove the screw.
Disengage the inside door handle from the door.
If equipped, disconnect the power door lock rod from the back of the inside door handle.

Gain access to the power window motor electrical connector located in the front of the door.
Fig. 90: Identifying Power Window Motor Electrical Connector
Courtesy of FORD MOTOR CO.
Disconnect the power window motor electrical connector.
Press down on the connector tab.
Pull the connector upward and remove through the speaker opening in the door.
Disconnect the rear door window regulator and motor assembly from the door.
Remove the nuts.
Remove the screws.
Fig. 92: Disconnecting Rear Door Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_2.jpg
Remove the window regulator and motor assembly from the door.
Fig. 93: Removing Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_3.jpg

To install, reverse the removal procedure.

Posted on Jul 01, 2009

  • 9 Answers

SOURCE: how to replace fuelpump 92 fuel pump do you have

yes

Posted on Jul 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the trunk release button in the glove box of my 1991 ford tempo work off of a fuse?


Yes ,inside fuse panel . fuse #6 it's a 20amp ! Do you know where it is , the fuse panel ? Under the drivers side dash .

Sep 15, 2016 | 1991 Ford Tempo 4 Door

1 Answer

Ford tempo temp gauge not working


Ect engine coolant temp sensor bad

May 16, 2016 | 1992 Ford Tempo

1 Answer

92 ford tempo engine cooling fan wont run


Its probably a relay (big funny looking fuse thingy), or your thermostatic control unit. Search any fuse panel in the car for anything thats labeled fan, and try replacing it. I'd suggest checking under the hood first, then move to your internal fuse block

Jul 19, 2012 | 1992 Ford Tempo

1 Answer

Drivers door wont open


If it were me , I'd remove the inside door panel and take it from there. It may be that you can pry open the lock mechanism with a screw driver or a similar tool, allowing you to open the door - which obviously you must do. Even that, though, will not solve the cause of your problem. You may wind up at the dealer.

Aug 19, 2017 | 1986 Ford Tempo

1 Answer

Replaced neutral switch in 92 ford tempo. now the


Did you knock the linkage off from the throttle body to the transmission right above the neutral safety switch?

May 17, 2010 | Ford Tempo Cars & Trucks

2 Answers

1993 Ford Tempo Electric windows will work sometimes and then the next time they will not. Please tell me what may cause this and if I can fix it.


Check wires between door and body where door hinges are. Then check connector at main harness inside drivers door. You will need to pull door panel for this. Under switch is a connector that sometimes gets corroded.:)

Sep 07, 2009 | 1993 Ford Tempo

1 Answer

I have a 1993 Ford Tempo and am having problems removing the motor from the door. I already have the door panel removed and the power disconnected from the motor.


remove the door panel and check to make sure the linkage to the lock assembly is still attached. I can't give an estimate because I don't know what is wrong at this point

are the locks manual or electric?i have seen most electric locks freeze up because of rust/.corrosion.the rubber accordian seal fails and moisture does it's job.there is no lubrication on the mechanism.it's basically a push pull magnet tube with a spiral grooved actuator rod.this is to assure no accidental vibration/jar induced movement.also means very difficult to budge when corroded.i have gotten a few to move by grabbing lock post with pliers and pulling hard.good luck!



Rear Door Window Regulator and Motor
Removal and Installation
Remove the rear door trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .
Remove the door mounted speaker.
Remove the watershield.
NOTE:The glass must be lowered for this step.

NOTE:Some vehicles may use rivets to attach the glass to the regulator.

Remove the bolt that attaches the glass to the regulator.
Raise and support the rear door window glass to the full up position.

NOTE:Do not detach the door handle from the latch cable during this step.

Remove the rear inside door handle.
Remove the screw.
Disengage the inside door handle from the door.
If equipped, disconnect the power door lock rod from the back of the inside door handle.

Gain access to the power window motor electrical connector located in the front of the door.
Fig. 90: Identifying Power Window Motor Electrical Connector
Courtesy of FORD MOTOR CO.
Disconnect the power window motor electrical connector.
Press down on the connector tab.
Pull the connector upward and remove through the speaker opening in the door.
Disconnect the rear door window regulator and motor assembly from the door.
Remove the nuts.
Remove the screws.
Fig. 92: Disconnecting Rear Door Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_2.jpg
Remove the window regulator and motor assembly from the door.
Fig. 93: Removing Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_3.jpg

To install, reverse the removal procedure.

Jul 01, 2009 | Ford Tempo Cars & Trucks

1 Answer

Door handles


You have to remove the inner door panels, remove all screws on inside some may be hidden under platic clip in pieces. after you remove them there will be a plastic sheet glued to door. pull this back and you will have access to the linkage, these clips can be purchaes at autoparts store or of course from the dealer. Hope this helps

Dec 15, 2008 | 1991 Ford Tempo 4 Door

1 Answer

Poping the hood with a don't inside latch of the hood


I have a 1999 Suburban that has several of the door latches that do not operate properly with the remote button or the power door lock button on the door. If your locks open okay with the key, it is most likely the lock actuator that is the problem. The coils on these can get weak and not be able to operate the locking mechanism. Changing them out is probably required. Haven't actually changed mine yet, but have taken door panel off to lubricate actuator rod. This helped only briefly. Good luck. The actuators themselves are quite expensive from the dealer. ($60-$80 each, excluding installation)
If you mean the door handle on the inside of the vehicle, it is probably broken. So, when you pull on it it can't pull the actuator rod. You have to change the handle assembly. They cost about $40. But you have to drill out the rivet. So buy a pop rivet gun and a trim removal tool. 1. Un-bolt the window regulator panel (after you have removed the trim panel) 2. Pull the top the panel back a bit. Lowering the window about 3 inches will help. But, don't pull on the panel too hard. 3. Stick rim removal tool in there and pop off the power door look rod. 4. Use you hand and pop off the handle actuation rod 5. Drill out the rivet on the latch assembly 6. Slide assembly forward and remove. 7. Do things in reverse to reassemble

Jun 20, 2008 | 1986 Ford Tempo

Not finding what you are looking for?
1992 Ford Tempo Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...