Question about 1999 Chrysler Cirrus

Open Question

Directions on how to replace egr valve on a 1999 chrysler cirrus

Posted by Anonymous on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 96 Answers

SOURCE: 1999 Chrysler Cirrus Lxi 2.5l high rpm

The throttle position sensor may be misaligned. This tells the computer how much throttle is being applied, and when they go bad, or come out of alignment, the idle tends to get up there. If that's not the issue, remove your air cleaner, the housing and everything until you get to the MAP sensor. Give it a good spray with carb cleaner, let it dry and replace the air cleaner with a new one. If the MAP sensor detects minimal air flow, the computer jacks up the idle to compensate.

Posted on Nov 07, 2008

  • 4 Answers

SOURCE: Need to replace EGR valve

The exhaust gas recirculation valve is located on the intake manifold on my Isuzu. All it does is make the exhaust coming out of the tailpipe less poisonous. I'm ironiclly going to replace mine tomorrow. There should be a wiring connecter that you dissconnect and a large outgoing pipe that you need to unthread and remove. All that is holding on your EGR valve are two bolts. Remove those and the gasket and good riddance! Scrape the intake manifold with a razor blade, gently to remove the gasket completely and thread on the gasket to the new valve. Then just rebolt everything and plug in the electrical connection and start the engine. It should sound good.

Posted on Jan 12, 2009

  • 353 Answers

SOURCE: How do you replace the EGR valve on a 2004

check with you dealer, that part may have a manditory extended warranty by law

Posted on Jun 24, 2009

  • 3854 Answers

SOURCE: 1999 chrysler cirrus transmission will not shift

It sounds like it may be you speed sensor at the transmission which is also called Vehicle Velocity Sensor (VVS), The sensor or the wire harness may have gone bad and needs to be replaced, but it's a good thing to have your car scanned at Auto Zone since they scan free of charge. I just want to make sure it is the VVS and not the transmission Control Module (TCM), Check the fuse under the dash and under the hood and look for any blown fuse like the TCM fuse. Good luck and hope this helps, keep me posted

Posted on Jun 24, 2009

  • 1 Answer

SOURCE: Code P0406

Where is the egr valve on my crystler 300?

Posted on Aug 17, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Bottom hose on egr valve keeps blowing off, what could be causing this?

Hoses are a vacuum source,they won't come off,
unless somehow the valve is shot inside & exhaust
gases have some effect

You should have a MI Lamp lite if the valve was bad

Sep 30, 2014 | 2000 Chrysler Cirrus

1 Answer

Burning coolant

check for corrosion holes in the egr valve housing Replace if corroded

Dec 28, 2013 | 2000 Chrysler Cirrus

1 Answer

1999 chrysler cirrus engine is smoking

i would start with washing the engine down with a degreaser the smoke could be old oil burning off then if you still have a burning smell you will know its fresh you can get a dye from a parts store and with a black light you can trace the leak

Aug 08, 2012 | 1999 Chrysler Cirrus

1 Answer


EGR valve , either the valve is malfunctioning, or the electronic control is...

Jun 19, 2012 | 1999 Chrysler Cirrus

4 Answers

99 chrysler cirrus lxi won't shift out of 2nd, no speedometer

Had the same problem on my 1999 cirrus lxi. Replaced the output speed sensor on the tranny and topped off the tranny fluid... cleared the check engine light and the cirrus ran great. Caution...the output speed sensor reqires removal of the front left tie and plastic weatherproofing to replace. once you find it's locvation, the replacement is relatively easy.

Oct 30, 2009 | 1999 Chrysler Cirrus

1 Answer

Where is oil sending unit location on 1999 chrysler cirrus 2.4 ?

most likley place is on the engine block look for it there

Oct 24, 2009 | 1999 Chrysler Cirrus

1 Answer

Master cylinders number 2,4,5,6 are miss firing

I'd say most likely you're catalytic converter and or the EGR valve may need repaired or fixed. THe EGR recycles some exhaust in order to recombust fuel. The catalytic converter reduces toxicity of emissions. Car dealers can diagnose these thing for around $100-200.

Sep 28, 2009 | 1999 Chrysler Cirrus

1 Answer

How to find oil bolt to change oil on 1999 chrysler cirrus

lift up the car on ramps or a jack and crawl underneath the front of the car the oil pan is directly below the motor at the lowest point you will find the bolt

Mar 10, 2009 | 1999 Chrysler Cirrus

Not finding what you are looking for?
1999 Chrysler Cirrus Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides