Question about Ford Cars & Trucks

Open Question

1996 ford explorer 5.0 v8 code p0446,code p0346

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
sir fixalot
  • 146 Answers

SOURCE: 1997 ford explorer V8 5.0 engine

P1405-Differential Pressure Feedback Electronic (DPFE) sensor upstream hose off or plugged - or cracked.

I believe it is on the driver's side of engine about half-way down. also, check all other hoses for damage

Posted on Jun 04, 2008

Ad
Papa Chan
  • 56 Answers

SOURCE: O2 sensors

The o2 sensor you are looking for is on the drivers side of the engine and it is the first on closest to the engine. Before the cat. I hope this is helpful.

Posted on Jan 05, 2009

fischmilch
  • 96 Answers

SOURCE: install water pump

5.0L Engine
Removal

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the fan/clutch assembly and shroud.
  4. Loosen the water pump pulley attaching bolts.
  5. Remove the accessory drive belt.
  6. Remove the water bypass hose from the pump.
  7. Disconnect the heater hose at the pump.
  8. Remove the engine control sensor wiring harness brackets and position the harness out of the way.
  9. Remove the water pump pulley.
  10. Remove all of the water pump attaching bolts. Pay attention to the locations of any stud bolts.
  11. Pull the water pump away from the front cover, then disconnect the lower radiator hose from the pump
  12. Lift the water pump from the vehicle.
    To install:
  13. Clean the mounting surfaces of the pump and front cover thoroughly. Remove all traces of gasket material.
  14. Apply adhesive gasket sealer to both sides of a new gasket and place the gasket on the pump.
  15. Install the lower radiator hose to the water pump.
  16. Position the pump on the cover and install the bolts finger-tight. When all bolts are in place, torque them to 15-21 ft. lbs. (20-28 Nm).
  17. Position the engine control sensor wiring harness and install the retaining nuts.
  18. Install the water pump pulley and its attaching bolts. Snug the bolts.
  19. Install the heater and water bypass hoses to the water pump.
  20. Lift the accessory drive belt tensioner and install the belt.
  21. Securely tighten the water pump pulley attaching bolts.
  22. Install the engine fan/clutch assembly and the shroud.
  23. Refill and bleed the cooling system.
  24. Connect the negative battery cable, start the engine and check for leaks.

Posted on Mar 20, 2009

bitchn65cuda
  • 70 Answers

SOURCE: high mileage 1996 Ford Explorer v8 overheats at 75-80 mph

if your mechanic seen no leaks from hoses or thermostat housing its sounds that either your fan clutch or your thermostat is bad. if its heats will driving streets and not highway its your fan clutch and needs to be replaced. if it overheats in streets and highway its your thermostat and needs to be replaced,you will need a thermostat and gasket with some silicone. Drain, follow the radiator hose to the housing and take 3 bolt off, clean housing well,CAREFULLY install the t-stat exactly the way is was taken out (pic), gasket,sillicone, bolt. ecc3d0c.jpg   its an easy job. Good luck!

Posted on Apr 27, 2009

  • 25 Answers

SOURCE: 1996 Ford Explorer XLT abs light comes on on

The ABS light is for the Anti-lock Braking System. The MIL will illuminate if there is a difference in wheel speed sensors signals to the PCM. So you might have a wheel speed sensor that is going out on you. Does the light come on at low speeds, or just higway speeds? You could take the vehicle to a local parts store and have them pull the codes for you and that will tell you which speed sensor is out of whack. Also road grime, dirt and gunk buildup can cause speed sensors to give false readings. Hope tihs helps you out.......

Posted on Oct 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code p0446, code po340


P0446 is a malfuntion in what is called your EVAP system spicifly the canaster purge valve . What this system dose is it takes fuel vaper and exese fuel from the fuel return at the gas tank and on damand at at hire speed or heavy load and send it to the intake manifold to be burned so it dosn't leak into the atimisphere. The P0340 code is a mis fire on #4 cylinder random and is being caused by the 0446 code.P01850 sounds like a transmissiton code that is like a byproduct and also caused by the P0446 as well .The first thing to check is the gas cap the system is a sealed system its the cheapest and easyest thing to check if it is leaking it would cause all of these problems . If its not that then you need to look at canaster purge valve its one of these two things

Feb 21, 2012 | 1996 Ford Explorer

1 Answer

Need the fireing order


For the 1996 Ford Explorer
I do not know if you have the 4.0L V6 or the 5.0L V8; however I have included both below:

For the 4.0L V6:
Firing Order:
1-4-2-5-3-6
Cylinders:
....(back)....
'..3..'..'..6..'
'..2..'..'..5..'
'..1..'..'..4..'
...(front)
Coil Connections:
....(back)....
'..1...2...3..'
'..5...6...4..'
....(front)

For the 5.0L V8:
Firing Order:
1-3-7-2-6-5-4-8
Cylinders:
......(back)......
'..4..' .....'..8..'
'..3..'......'..7..'
'..2..'......'..6..'
'..1..'......'..5..'
......(front)
Distributor Connections:

[..].3...1
7..............8
2..............4
.....6...5.[..]

Let me know if this helped....Thank you for using FixYa.com!

Sep 22, 2010 | 1996 Ford Explorer

1 Answer

After i've been driving for about 30-60 mins. and


Idle air controll motor is bad, 60 dollar part and 5 mins to change

Jun 12, 2010 | 1996 Ford Explorer

1 Answer

What is the firing order of the sparks plugs


2.3L 4: 1 - 3 - 4 - 2

4L V6: 1 - 4 - 2 - 5 - 3 - 6

5L V8: 1 - 3 - 7 - 2 - 6 - 5 - 4 - 8

Apr 26, 2010 | 1996 Ford Explorer

1 Answer

P0446 error code 2004 ford explorer


Hi jh9848, I'm glad to help!

P0446 code is related to the Evaporative Emission Control System Vent Control Circuit Malfunction. Anytime a "CIRCUIT" is involved it can be the component itself OR the wiring and connector that goes to that component. Sometimes it can be the controller but not very often. On most vehicles the vent control system is part of the emissions canister. You'll need to contact the dealer and ask them. Hope this helps and have an awesome day jh9848.

Apr 16, 2010 | 2004 Ford Explorer

1 Answer

Need firing order for coil pack, 1994 ford explorer,4.0


V8 or V6

Cyl 1 thru3 or 4 ---front to back --pass side

Cyl 4 thru 6 --or 5 thru 8 in case of V8 --driver side

V6 1-4-2-5-3-6

V8 1-3-7-2-6-5-4-8

Mar 12, 2010 | 1994 Ford Explorer Limited

2 Answers

Need diagram of firing order


Sorry for the delay.
I am personally going back to answer your unanswered question. I do not know if you still need the answer, but I am going to answer it in case you still do.


I do not know if you have the 4.0L V6 or the 5.0L V8; however I have included both below:

For the 4.0L V6:
Firing Order:
1-4-2-5-3-6
Cylinders:
...(back)
3...........6
2...........5
1...........4
...(front)
Coil Connections:
...(back)
1....2....3
5....6....4
..(front)

For the 5.0L V8:
Firing Order:
1-3-7-2-6-5-4-8
Cylinders:
.....(back)
4...............8
3...............7
2...............6
1...............5
....(front)
Distributor:
.....(back)
(+)..3....1
7...............8
2...............4
......6....5..(+)-screw
......(front)

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


Oct 19, 2009 | 1996 Ford Explorer

1 Answer

P0446


Check for any damage to the cap or on the wiring if no damage is visable replace the cap.

Aug 27, 2009 | 2007 Ford Explorer Eddie Bauer

1 Answer

O2 sensors


The o2 sensor you are looking for is on the drivers side of the engine and it is the first on closest to the engine. Before the cat. I hope this is helpful.

Jan 05, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...