Question about 1999 Isuzu Amigo

1 Answer

Where is the cmp located on a 99 amigo 3.2 engine

Camshaft sensor location on the 3.2 amigo

Posted by on

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

The camshaft position sensor (CPS) is located on the side of the left cylinder head. It's shadowed underneath the intake manifold.

Posted on Feb 21, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 8 Answers

SOURCE: thermostat on 1998 Isuzu Amigo

Yes, It's under the intake manifold. The manifold would need to be removed Lower hose from radiator is attached to steel pipe leading to it. It will not be an easy mission,and the new thermostat is rated for I believe 170 degrees. That's not much help to keep the interior warm with a rag top when it's 20 below zero.

You can boost the heating level by adding vinyl cover over the front portion of grill. Any boat interior shop has the material. Modify any large air leaks. Use the fan to keep fresh air filling vehicle, not recirculate.

Posted on Nov 16, 2008

emissionwiz
  • 77499 Answers

SOURCE: where is the water pump located on a 1993 isuzu amigo

it is on the front of the engine, the cooling fan is attached to it, do u have the new part?

Posted on May 30, 2009

honeymokey
  • 3113 Answers

SOURCE: how do I replace the camshaft position sensor on

4cyl? Its behind th timing cover between the cam pulleys. Should take about 15 minutes to replace. loosen upper cover and pull back to expose part

Posted on Sep 28, 2009

stevenhurc
  • 450 Answers

SOURCE: where do i locate the

it is located on the inner rear section of the left hand head (left side of vehicle) under inlet manifold dont need to remove inlet manifold
and connector must face rearwards to work correctly


stevenhurc_4.jpg

Posted on Feb 04, 2011

  • 118 Answers

SOURCE: What's an egr? Where is located on 1999 isuzu

EGR stands for exhaust gas recirculation, the main function of this valve is to allow exhaust gases to re-enter through the intake to help lower engine temperatures, and control emissions. Search around the intake manifold area, this is usually where it is mounted.

Posted on May 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is cam shaft sensor located on a 08 saturn aura


Which engine ? This vehicle had option of six different engines , 2.4 , 3.5 , 2.8 , 3.0 , 3.2 , 3.6 And are you picking on the right part ? What code > DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit
It may not even be a cam sensor problem !
DTC P0340: Intake CMP Sensor Circuit

DTC P0365: Exhaust Camshaft Position (CMP) Sensor Circuit
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance
Camshaft Position (CMP) Actuator System
The camshaft position (CMP) actuator system is an electro-hydraulic operated device used for a variety of engine performance and operational enhancements. These enhancements include lower emission output through exhaust gas dilution of the intake charge in the combustion chamber, a broader engine torque range, and improved fuel economy. The CMP actuator system accomplishes this by changing the angle or timing of the camshaft relative to the crankshaft position. The CMP actuator simply allows earlier or later intake and exhaust valve opening during the four stroke engine cycle. The CMP actuator cannot vary the duration of valve opening, or the valve lift.
During engine OFF, engine idling conditions, and engine shutdown, the camshaft actuator is held in the Park position. Internal to the CMP actuator assembly is a return spring and a locking pin. During non-phasing modes of the camshaft, the return spring rotates the camshaft back to the Park position, and the locking pin retains the CMP actuator sprocket to the camshaft


It may

Jul 06, 2016 | 2008 Saturn Aura

1 Answer

Coolant temp sensor location on 1998 Isuzu Amigo 2.2L 4X4.


Go in on utube and ask the question Where is the 1998 Isuzu amigo coolant temp sensor located good luck

Oct 22, 2014 | 1998 Isuzu Amigo

1 Answer

Where is the camshaft position sensor located in a


The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Oct 10, 2014 | Cars & Trucks

2 Answers

Where is 2003 ford focus camshafts position sensor


Camshaft Position Sensor
The camshaft position (CMP) sensor detects the position of the camshaft. The CMP sensor identifies when piston No. 1 is on its compression stroke. A signal is then sent to the powertrain control module (PCM) and used for synchronizing the firing of sequential fuel injectors. The Coil On Plug (COP) Ignition applications also use the CMP signal to select the proper ignition coil to fire. The input circuit to the PCM is referred to as the CMP input or circuit.
There are two types of CMP sensors: the three pin connector Hall-effect type sensor (Figure 25) and the two pin connector variable reluctance sensor

a452a319-2d08-4e59-9885-fe43b5fc7f61.gif

and next the location of 2003 ford focus camshafts position sensor
96d62950-03fc-4668-b3ad-dfa939f76b14.gif

Sep 13, 2014 | 2003 Ford Focus

1 Answer

Location of camshaft position sensor on 2009 saturn aura


2.4L cmp sensor exhaust located upper rear of the engine near camshaft cover. 2.4L cmp sensor intake located upper front of the engine near the camshaft cover. the 3.5L cmp sensor located right side of engine compartment above the timing chain cover.below power steering pump.3.6L cmp sensor located right side of the engine near the front and rear.

Sep 26, 2013 | Cars & Trucks

1 Answer

I went to scan my toyota yaris car and the following codes were give ; temperature ckt low input po117


EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

Dec 13, 2012 | 2001 Toyota Yaris

1 Answer

Do you have to remove the cam gear to change the camshaft senaor.


Courtesy of a Beetle forum.

The camshaft position sensor is located at the front of the cylinder head under the timing belt cover. On 2.0L models, the camshaft position sensor is located behind the camshaft sprocket and is equipped with a pigtail lead and a remote connector. On 1.8L turbo models, the camshaft position sensor is located at the front of the intake camshaft. check the terminals in the connector and the wires leading to the sensor for looseness and breaks. Repair as required.

Before checking the camshaft position sensor, check the voltage supply and ground circuits from the ECM. Dosconnect the electrical connector from the camshaft position sensor and connect a voltmeter to terminals 1 and 3 at the harness connector from the camshaft position sensor and connect a voltmeter to terminals 1 and 3 at the harness connector. Turn the ignition key On - the voltage should read approximately 5.0 volts. If the voltage is incorrect, check the wiring from the camshaft position sensor to the ECM. If the circuits are good, have the ECM checked at a dealer service department or other properly equipped repair facility.

To check the camshaft position sensor operation, reconnect hte connector to the camshaft position sensor and using a suitable probe, backprobe terminal no. 2 of the camshaft position sensor connector. Connect the positive lead of a voltmeter to the probe and the negative lead to a good engine ground point. Turn the ignition key On. Rotate the engine slowly with a breaker bar and socket attached to the crankshaft pulley center bolt while watching the meter. The voltage should fluctuate between zero volts and 10.0 volts as the vanes in the reluctor wheel past the sensor. If the test results are incorrect, replace the camshaft position sensor. Note: Rotate the engine slowly through at least two complete revolutions. Removing the spark plugs from the engine will make the crankshaft much easier to turn. Warning: If you remove the spark plugs, unplug the primary (low voltage) electrical connector(s) from the ignition coil(s) to disable the ignition system

Jul 11, 2012 | Cars & Trucks

1 Answer

Location on 2005 trailblazer of Camshaft Position Sensor


4.2l engine cmp sensor located front right corner of the engine cylinder head. 5.3l engine cmp sensor location front of the engine block just above the crankshaft.

Nov 23, 2011 | 2005 Chevrolet Trailblazer Ext

1 Answer

Where is the camshaft position sensor located on a 06 jeep grand cherokee limited 4.7 l automatic ? ... also the crank position sensor


The CMP sensor engine contains a hall effect device called a sync signal generator to generate a fuel sync signal. This sync signal generator detects notches located on a tonewheel. The tonewheel (4) is located at the front of the camshaft for the right cylinder head (2). As the tonewheel rotates, the notches (1) pass through the sync signal generator. The pattern of the notches (viewed counter-clockwise from front of engine) is: 1 notch, 2 notches, 3 notches, 3 notches, 2 notches, 1 notch, 3 notches and 1 notch. The signal from the CMP sensor is used in conjunction with the crankshaft position sensor to differentiate between fuel injection and spark events. It is also used to synchronize the fuel injectors with their respective cylinders.


ledsled378_115.jpg

ledsled378_116.jpg

May 12, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Where is the location of camshaft sensor, vehicle will not start


The camshaft position sensor (CMP) on the 3.0L OHC (4 valve) and 3.4L SHO engines is a variable reluctance sensor that is triggered by a high point on the left-hand exhaust camshaft sprocket. The CMP sends a signal relating camshaft position back to the PCM which is used by the PCM to control engine timing.

The camshaft position sensor (CMP) on the 3.0L OHV (2 valve) engine is a single hall-effect magnetic switch that is triggered by a single vane which is driven by the camshaft. The CMP sends a signal relating camshaft position back to the PCM which is used by the PCM to control engine timing.

Hope helps.

Sep 26, 2010 | 1999 Ford Taurus

Not finding what you are looking for?
1999 Isuzu Amigo Logo

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...