Question about 2004 Ford Focus

1 Answer

2004 ford focus headlights

The low and high beams do not work when turned on, have running lights, side lights etc. checked the fuses and look fine, not sure if BOTH bulbs are out, anything I should look at before taking in to have repaired?

Posted by on

  • 1 more comment 
  • Anonymous Dec 25, 2008

    No head lights at all, all fuses are ok, also the fuses from the engine compartment

  • Greg Wilkins
    Greg Wilkins May 11, 2010

    Do you mean you don't have high beams or just no head lights at all.

  • Sandra Cass
    Sandra Cass Dec 20, 2013

    I replaced the dimmer switch and the light switch in the dash and the relay fuse still no low beams help

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 580 Answers

You need to replace the high/low beam switch

Posted on Jul 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a problem with the low beams on my headlights. The high beams works just fine. All of the other lights(turn signal, emergency lights, etc.) work except for the low beams.


Check the fuses first. then replace the turn signal switch if all fuses are good. All the lights run threw it, except the high brake light on the rear.

Jan 01, 2015 | 2003 Ford Escape

1 Answer

No power to right side (PS) headlight low beam plug socket, new bulb, fuse is good. High beam works, blinker works, park light works. just no low beam and doesn't register any voltage on volt meter.


check low beam fuse when switched on if it has voltage registering across the fuse ,if there is voltage across the low beam RHS fuse then it is possibly a pinched wire from the headlight running back towards inside of the car

Jan 30, 2014 | Cars & Trucks

3 Answers

One low beam head lights will not work, high beam works though


check for a damaged wire for the low beam. Also wouldn't hurt to check the ground wire as the high beam will try and ground through the low beam but not visa verse

Dec 29, 2013 | 1997 Chevrolet Blazer

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

2 Answers

Prius high beam lights work but low beam lights do not work?


On a 2008 Prius, If both High beams work but only one side has working low beams, then it is most likely a fuse. So before breaking your knuckles to change the bulb, check the fuse first. I found out the hard way as my mom distressed to me that her drivers side headlights were out. So without checking to see if low and high were working, I proceeded to remove and replace the bulb - ouch! There are 4 10 amp fuses that protect the circuits for low/high beam function. They are under the hood in the fuse box on the drivers side and they are marked on the box cover. Check them before changing the bulb.

Oct 29, 2012 | 2006 Toyota Prius

1 Answer

Both low beam headlights are out.


check for voltage at the high beam switch when high beams are turned on.

Oct 08, 2012 | 2004 Ford Focus

2 Answers

Headlights do not work. Beam works, park lights and other lights work. Bulbs ok


more than likely a fuse or a relay is bad. locate the fuse for the headlights (owners manual) and check if it is bad, if the fuse is good, find the relay and give it a flick or two and try the headlights then, if they work, its time for a new relay

Mar 19, 2011 | 2006 Ford Focus

1 Answer

98 ford lariat. Headlights stopped working. running lights come on and brake lights and turn signals. checked all fuses under dash and under hood, pulled out headlight switch and it looks fine. note only...


Is this both the high beams and low beams that do not work ?

If you checked all 3 fuses with a meter ( with the headlamp in Low position for both low beam fuses or in high for the high beam fuse ), the next items to test are the MFS ( MultiFunction Switch ) and the main headlamp switch ( test not look at it ).

The main headlamp test chart
568bbbb.jpg

The test chart for the MFS
4fc6f66.jpg
097ea29.jpg

Oct 25, 2010 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
2004 Ford Focus Logo

1,027 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...