Question about Mitsubishi Cars & Trucks

1 Answer

Thermostat housing complete

Pls

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 77,169 Answers

We have no parts here, just advice. Sorry.

Posted on Feb 21, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is thermstat


Assume you are asking about the thermostat. You can find it by tracing the radiator hose to where it connects on the intake manifold. The piece it connects to is the thermostat housing. The thermostat lives inside that housing.

Jul 17, 2014 | 1998 Ford Escort

1 Answer

How to replaced thermostat of toyota avanza 2007 model


route the radiator hose to the engine. from radiator the coolant hose goes to thermostat housing. remove that housing so you can find thermostat. you may need to remove the hoses before removing the thermo housung

Apr 13, 2014 | 2007 Toyota Sienna

1 Answer

Remove thermostat


the complete housing has to be replaced as there will be a corrosion hold in the aluminium

Dec 22, 2013 | Cars & Trucks

1 Answer

Replace thermostat in a 1997 Dodge Intrepid


The thermostat is an easy replacement. The part from the part store should be very inexpensive and is very easy to install. IMPORTANT: allow the cars cooling system to completely cool down before starting to work on it. Here are the steps to replace the thermostat:

1. Allow car to cool.
2. Place drain pan under radiator and allow for coolant to drain below the thermostat. Do not completely drain the system unless replacing the fluid.
3. Remove the hose clamp and hose from thermostat housing.
4. Remove the two bolts holding the housing to engine.
5. Remove the thermostat gasket and clean the gasket completely off the engine and thermostat housing.
6. Remove the thermostat and replace with new.
7. Place new gasket on with reassembly.

Oct 12, 2013 | 1998 Dodge Intrepid

1 Answer

Need to change engine thermostat on 2002 saturn vue. would like diagrams on how to and what to look for.


2.2L Engine To Remove:
  1. Drain the cooling system.
  2. Remove the exhaust manifold heat shield.
  3. Remove or disconnect the following:
  4. Thermostat housing to water pump feed pipe chevy_cav_02-04_tstat.gif
  5. Remove the thermostat cover bolts from the thermostat housing.
  6. Remove and discard the thermostat housing O-ring.
  7. Thermostat assembly saturn-03-22-4279.gif
  8. Twist the water feed pipe while pulling to remove it from the water pump. Remove the water pipe from the water pump assembly.
  9. Remove and discard the seals from the water pipe.
  10. Remove the inner thermostat sleeve.
  11. Remove the thermostat assembly.
To Install:
  1. Install the thermostat cartridge into the thermostat housing while aligning the cartridge tangs up with the thermostat housing bolt holes. This will assure the inner sleeve can be completely installed.
  2. Align and insert the inner sleeve notch into the thermostat housing. If the inner sleeve notch is not properly positioned, the sleeve will not completely seat into the housing.
  3. The water feed pipe seals can be slightly lubricated with silicone gel to aid during installation. Install a new O-ring on the water pipe.
  4. Position the water pipe into the water pump assembly.
  5. Seat the water feed O-ring by pushing and twisting toward the water pump. Take care not to tear or damage the O-ring.
  6. Install the thermostat housing cover to the water pipe. The water feed pipe has a locating tab to assure proper alignment.
  7. Install a new thermostat housing cover seal into the recess groove.
  8. Position the thermostat housing cover into position.
  9. Install the thermostat housing cover bolts and tighten bolts to (89 in-lb 10 Nm).
  10. Install the exhaust manifold heat shield.
  11. Fill the cooling system.

Dec 24, 2010 | 2002 Saturn VUE

1 Answer

Is not heating


  • Raise and fully support the hood on the ford Remove the radiator cap and place a coolant drain pan underneath the radiator.
  • Open the drain-**** on the radiator and completely drain all of the coolant from it. It should take 10 minutes to fully drain. After this time close the drain-**** securely.
  • Locate the thermostat housing on the side of the engine below the alternator. It's not necessary to remove the hose from the thermostat housing. You can access the thermostat easily once the housing unbolted.
  • Slide your coolant drain pan directly beneath the thermostat housing. This way any coolant that comes out of the housing will go into the drain pan and not on the ground.
  • Remove the two bolts holding the heater core housing to the engine with a socket wrench. Pull the housing away from the engine and take out the thermostat.



  • Install the new thermostat just as you removed the old thermostat. Your new thermostat should have a rubber seal already installed on it, if not you have the wrong replacement part.
  • Position the thermostat housing back into its original location and then return both of its bolts by hand to insure they thread correctly. Set your 1/4-inch drive torque wrench to 89 inch-lbs. and completely secure both bolts in place.
  • Refill the radiator with fresh coolant or with the coolant from the drain pan if it's less than three years old. Return the radiator cap and then start the engine on the Bravada. Check for leaks every five minutes until the engine reaches normal operating condition. Take the truck for a test drive once you've determined there aren't any leaks present.



  • Dec 04, 2010 | 2002 Ford Taurus

    1 Answer

    Were is my thermostat in my 1997 eagle vision


    REMOVAL & INSTALLATION
    1. Disconnect negative battery cable. CAUTION
      Do not remove the radiator pressure cap with the cooling system hot and under pressure. Serious burns from hot, pressurized coolant can result.
    2. Allow cooling system to cool completely. Place a pan under the radiator drain, located at the lower right side of the radiator. Open the valve to drain the cooling system to a level just below the thermostat. Do NOT drain the cooling system completely, unless the coolant is being changed. Close the valve.
    3. Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing and if necessary disconnect the hose from the housing. Fig. 1: Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing 88173p06.jpg
      Fig. 2: If necessary, separate the upper hose from the thermostat housing (it is not required) 88173p11.jpg

    4. Remove the thermostat bolts and housing. Fig. 3: Loosen the thermostat housing bolt with the proper size socket 88173p07.jpg

    5. Remove the thermostat and discard the gasket. Thoroughly clean both gasket sealing surfaces. Fig. 4: Separate the housing to access the thermostat 88173p08.jpg
      Fig. 5: Lift the thermostat out . . . 88173p09.jpg
      Fig. 6: . . . then clean the mating area 88173p10.jpg
      To install:
    6. Clean the thermostat housing bolts well. On any engine, bolts that thread into the water jacket are subject to rust and corrosion. A bolt with rust or debris in the threads can easily strip out the threads in an aluminum manifold requiring a time-consuming thread repair operation. Clean the bolts well and lightly lubricate before installation.
    7. Install the thermostat into the recess in the intake manifold. Place a new gasket, moistened with water, on the water inlet mating surface on the intake manifold.
    8. Install the thermostat housing over the gasket and thermostat and tighten the mounting bolts to 21 ft. lbs. (28 Nm) on the 3.3L engine and 105 inch lbs. (12 Nm) on the 3.5L engine.
    9. Connect the upper radiator hose to the thermostat housing and tighten the radiator hose clamp.
    10. Refill and bleed the cooling system.
    prev.gif next.gif

    Aug 19, 2010 | 1997 Eagle Vision

    2 Answers

    How do i remove rhe thermostat from the housing in a 2004 GMC Envoy


    Hello, to remove the thermostat from the housing , follow this steps:

    1. Remove the necessary coolant from the radiator.
    2. Remove the alternator, Loosen the outlet hose clamp at the thermostat housing. Remove the outlet hose from the thermostat housing.
    3. Remove the thermostat housing bolts.
    4. Remove the thermostat housing from the engine block.
    5. Clean all of the surfaces of the thermostat housing.
    6. Clean the sealing surface of the engine block.
    Thanks

    Aug 17, 2010 | GMC Envoy Cars & Trucks

    1 Answer

    Need to find where the thermastat is on a 2003 cadi


    It is in the rear of the engine by the firewall and the intake manifold will need to be removed to gain access t it.

    Engine Coolant Thermostat Replacement (LA3, LY9) Removal Procedure
    1. Remove the thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement .

    2. 790876.gif
      tif.gif
    3. Complete the following in order to remove the thermostat from the thermostat housing:
    4. 2.1. Depress the ears on both sides of the thermostat. 2.2. Rotate the thermostat until it clears the retaining feature of the housing. 2.3. Release the pressure from the thermostat. 2.4. Pull the thermostat from the thermostat housing.
    Installation Procedure

      790876.gif
      tif.gif
    1. Complete the following in order to Install the thermostat into the thermostat housing:
    2. 1.1. Align the thermostat pin to the thermostat housing orifice. 1.2. Depress the ears on both sides of the thermostat. 1.3. Rotate the thermostat until it aligns with the retaining feature of the housing. 1.4. Release the pressure from the thermostat.
    3. Install the thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement .

    Jul 10, 2010 | 2003 Cadillac CTS

    1 Answer

    My Geo tracker 95 shows overheat on the assistant board.


    track the top hose from the radiator back to the engine where it should run into a rounded housing. This is the thermostat housing. Next time the vehicle shows its running close to 180 or higher (dont let it get too hot or your engine will fail completely)
    With the engine to temp, squeeze the upper radiator house. If it is hard then your have pressure running through the line, so then check the lower one. If no pressure, its your water pump.

    if hose can be squeezed, then the thermostat is not opening and allowing the coolant to circulate. Smack the housing a few times with some hard and blunt until you feel pressure in the hose again, or the temp gauge begins to regulate (if this is the case, you need a new thermostat; they are about $5 at any auto parts store......just remember to replace the gaskets while your at it)

    GOOD LUCK AND PLS RATE THIS POST!!!!!!

    Jun 03, 2010 | Chevrolet Tracker Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    15 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mitsubishi Experts

    yadayada
    yadayada

    Level 3 Expert

    77169 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8732 Answers

    Are you a Mitsubishi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...