Question about 2008 Chrysler Sebring Convertible

Open Question

Abs light comes on and stays on but break fluid level is full.

The ABS light came on and stays. I thought may be it needed brake fluid, so I filled it up. However, the ABS light is still. What might be the problem?

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 51 Answers

SOURCE: brake and ABS warning lights on, trac off on.

You may have a bad abs controller. You need to get the code for the abs light from a shop or auto parts store.

Posted on Oct 08, 2008

motor1258
  • 6674 Answers

SOURCE: ABS & Brake light stay on?whats the prob?what needs to be done?£?

Obviously a time for a brake checkover, but if the weather there is snowy & slushy, then perhaps a trip to a carwash & spraying as best as you can behind the wheels, may clean out some debris that may be making one or more of your sensors trip. Not too sure how experienced you are at these type of repairs, as I suspect one or more of your ABS sensors is dirty or faulty, it may be wise to have them checked for safety sake. Be aware that when light is on,ABS may not work, and could allow one or more wheels to lock up when hitting brakes hard in an emergency stop like situation.

Posted on Jan 30, 2009

  • 6 Answers

SOURCE: brake and abs lights and engine light on

have to pull the codes on each system to find problem but the other shop should look at it again if they just worked on it

Posted on Mar 26, 2009

  • 412 Answers

SOURCE: 2002 concord abs-brake airbag light stay on untill bang steering

sounds like you have a faulty ignition switch..have seen this before

Posted on Jun 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My abs and brake light stay on while am driving


The computer has detected a condition that indicates a fault with the ABS/Traction system. Typically that's caused by a wheel sensor problem, but it can also be caused by a faulty connector, peripheral device or the computer.
The above is the shop or garage answear. How about telling us how to fix the problem , besides replacing the computer or wheel sensor? How do we check these things?
Sometimes can be as simple as a short circuit in the rear break lights or a faulty connection in the break lights.
You can start checking the break light system. Then the sensors and finally the computer.

Antilock Brakes

Jul 29, 2016 | Cars & Trucks

1 Answer

My break light keeps coming on


You are low on brake fluid, the handbrake is engaged, or the switch on the handbrake needs to be looked at. If it is the ABS light, there is a problem with the ABS system. The brakes will still work fine, you'll just have regular brakes with no ABS.

Feb 20, 2014 | 1995 Eagle Summit

1 Answer

ABS pump and relay


First of all, make sure that your brake fluid level is correct. The brake, traction, and ABS systems on these cars all work together and if one thing goes wrong in any one part of the system, all of those lights will come on at the same time. Check your brake fluid level and be sure to use the correct DOT 3 brake fluid. DO NOT SUBSTITUTE with any other fluid. Let me know if your brake fluid level is ok and we'll go from there.

Aug 15, 2012 | 2001 Oldsmobile Aurora

2 Answers

Check breaks message displays on board I feel my car a little heavy and shaking behing


you need to check the brakes, your pads are probably worn to the point that the check brake light shows up,, also check the brake fluid level, it may need topping off, only fill it to the full line, not above , check around in your town, there are many shops that will check your brakes for free

Aug 29, 2011 | Kia Amanti Cars & Trucks

2 Answers

My brake and anti brake lights stay on all the time


CHECK ALTERNATOR OUTPUT IT SHOULD BE 13.5 TO 14.5 VOLTS WITH ENGINE RUNNING.IF VOLTAGE LOWER 12 VOLTS THAT WILL CAUSE BRAKE AND ANTI LOCK BRAKE LIGHTS TO COME ON BECAUSE THAT NOT ENOUGH POWER FOR ABS BRAKES OPERATION.IF ALTERNATOR GOOD.BRAKE AND ABS LIGHTS ON ALSO MEANS LOW BRAKE FLUID LEVEL CHECK BRAKE FLUID LEVEL.ALSO. YOU HAVING BRAKE FAILURE.YOU NEED TO HAVE GARAGE OR DEALERSHIP CHECK BRAKES SYSTEM.BEFORE BRAKES COMPLETELY FAIL.

Mar 23, 2010 | 1991 Dodge Dakota

1 Answer

Light stays on all the time


Some vehicles have the ABS light come on when it is time to change your breaks. Have a look at them, front and back. Also, check your Brake fluid level and your lines.

Mar 19, 2010 | 1997 Ford F350 Crew Cab

2 Answers

Abs light say on and breaK LIGHT


check your fluid level, and pads if good it could be a bad abs sensor

Jan 16, 2010 | 2002 Chevrolet Malibu

1 Answer

My brake light stays on and the fluid is full. what can i do to fix it


is it the abs light or the brake light there could be a couple different things wrong with it. if it's the abs light your abs system is acting up and it will need to be checked out. if it's the brake light then your brake fluid level sensor could be bad, or your parking brake switch could be going out, and there's other things that could be wrong with it.

Aug 23, 2009 | 1998 Ford Windstar

3 Answers

My brake light stays on in the dash


Typically, worn brake pads won't cause the warning light to come on. Some vehicles have a brake fluid sensor that can cause the light to come on. Also make sure the parking brake is completely releasing and if you have ABS, make sure everything is working there.
Uneven brake pressure will certainly cause the brake light to come on, that's when the master cylinder is working a lot harder for one circuit (front or back) than it is for the other, indicating either low brake fluid level or damaged/worn wheel cylinders.
If you can't find anything by examining the brakes, you may need to pay for a scan of the ABS computer.

Aug 07, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
2008 Chrysler Sebring Convertible Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...