Question about 2003 Pontiac Bonneville

Open Question

Motor mounts needs replaced how many are on a 2003 pontaic bonneville

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 341 Answers

SOURCE: replacing accessories belt 1997 bonneville (vin k)

on the 3.8 you have to take bolts out of motor mount and lift motor ...belt goes mount

Posted on Dec 10, 2008

johnny5846
  • 379 Answers

SOURCE: 1999 Pontiac Bonneville serpentine belt installation.

if you look by the crankshaft pulley to the right you will see a tubular looking shaft about 1" diameter , you will notice you can't get the belt out from under this piece , it has a nut on it , once you take the nut off , you will notice it has a star shaped point on the tip of the stud , it requires a reverse torx socket or wrench to remove the stud , when you get the stud out the tube piece it can be removed , then the belt comes off , replace the belt , now comes the tricky part , fitting that tube spacer back into its spot , it can be difficult , once its in place put the stud back in , and put the nut on and tighten it , your pretty much a pro now . thanks.

Posted on Dec 30, 2008

  • 1 Answer

SOURCE: 2004 Pontaic Bonneville humming noise wheel bearing?

I had a similar problem, when turning to the right or on a right curve, the noise would go away. After some research I found it was the left wheel bearing assembly. I replaced it and the problem is gone. Therefore, check the wheel bearing assembly. You may have to replace it.

Posted on Jun 09, 2009

  • 10 Answers

SOURCE: need to replace serpentine belt on 96 pontiac

On Bonnevilles (1996 SE ), the belt is routed around the front engine mount to get to the air conditioner accessory. Once you turn the tensioner counter-clockwise using I believe 5/8" socket with a 1/2" drive breaker bar, so you have good leverage, you can remove the belt from the accessories. The front engine mount has three legs that connect to the front of the engine (on the passenger side of the car). You have to unscrew the lowest of the three mounting points (easiest done from the under side of the car, with the plastic shielding moved out of the way), which is right next to the crankshaft pully. Then there is a round tube spacer in between the engine block and this leg of the engine mount that you take out, and you can pull the belt out through there.

Posted on Nov 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Three back spark plug install 2004 pontiac bonneville


you need a tool to rock motor toward grill it replaces motor mount just for this see most popular part stores will loan the tool

Oct 14, 2014 | 2004 Pontiac Bonneville

1 Answer

How to locate shift solenoid for 03 pontaic bonneville


Shift solenoids are inside the transmission. They attach to the valve body. Access them by removing the oil pan on the transmission.

Mar 01, 2012 | 2003 Pontiac Bonneville

1 Answer

How do I replace my throttle position sensor on a 2003 bonneville ssei


Hi, The tps is located on the side of the throttle body. Disconnect the wiring connector and then the two mounting screws. You may need to wiggle the tps a little to free it from the throttle body. Installing is just the reverse and there is no adjustment for these. Good Luck

Sep 13, 2010 | 2003 Pontiac Bonneville

1 Answer

Need location in vehicle of blower in a 2003 pontiac bonneville sse


These are typically located behind the glove compartment, or under the hood on the driver side mounted to the rear fire wall (usually older models).

Please let me know if you need further assistance.

carsandcomps,

Guru, Premium Expert @ Fixya.com

Jun 22, 2010 | 2003 Pontiac Bonneville

2 Answers

Blower is making a roaring noise and sounds like


The noise is caused from a bad or dried up bearing. You will need to replace the whole blower motor

Jan 12, 2010 | 2003 Pontiac Bonneville

1 Answer

Just wanted to change the #6 sparkplug how do i do this it seams hard to get to from thr top 1996 pontaic bondiville v6


to give more room - the motor cover can be taken off by unscrewing oil cap out of front valve cover - reach across or lay across motor to reach rear plugs

Sep 19, 2009 | 1996 Pontiac Bonneville SE CA Value

1 Answer

2004 Pontaic Bonneville humming noise wheel bearing?


I had a similar problem, when turning to the right or on a right curve, the noise would go away. After some research I found it was the left wheel bearing assembly. I replaced it and the problem is gone. Therefore, check the wheel bearing assembly. You may have to replace it.

Jun 03, 2009 | 2004 Pontiac Bonneville

1 Answer

Replacing accessories belt 1997 bonneville (vin k)


on the 3.8 you have to take bolts out of motor mount and lift motor ...belt goes mount

Dec 10, 2008 | 1997 Pontiac Bonneville

Not finding what you are looking for?
2003 Pontiac Bonneville Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...