Question about Chrysler Cars & Trucks

Open Question

Pressure relief and rollover valve in the tank of chrysler lebaron 1992

Locate in the top of the fuel tank

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2039 Answers

SOURCE: leaking coolant.

4 cyl under the ac compressor 6 cyl in the middle it driving by the timming belt you can not see it unless you remove the timing belt cover the 6 cyl 3.0 liter is and expensive job 4 to 6 hour labour plus part good luck pierre

Posted on Jun 26, 2008

  • 11 Answers

SOURCE: 1992 chrysler lebaron

First and foremost, check the fluid! Second, check ALL the vacuum lines in the vehicle. Now as for the fuse... referencing the shop manual, I can not find a transmission related fuse. Did you try checking the trouble codes, if any?

Posted on Jan 28, 2009

  • 1201 Answers

SOURCE: Location of Oil Pressure Sensor and Oil Pressure Relieve Valve

the oil pressure switch is on pssenger side, lower engine area,beside oil filter, mounted in engine block. The pressure relief valve is in the oil pump, in which case, you have to drop the oil pan,and take off the oil pump.

Posted on Jan 31, 2009

wireguy212
  • 1627 Answers

SOURCE: 1987 chrysler lebaron 2.5, car runs fine, then

i have had simmilar problems with my dodge dynasty and in the end an ignition coil fixed the problem.the fuel does only run for a second the will not run again until it see engine speed

Posted on Aug 07, 2009

BRADLEYFRANC
  • 104 Answers

SOURCE: looking for oil pressure relief valve on my 95 cabrio

The oil pressure relief valve should be on the oil pump.If your oil pressure is ok,have the wiring tested to theswitches or try another set of clocks

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 CHRYSLER lEbARON


If it cranks but won't start, have you checked for fuel pressure at the injectors and spark at the plugs ?

Jan 11, 2013 | 1992 Chrysler Lebaron

1 Answer

Where do I find the fuel filter on an 89 chrysler lebaron


On 1989 Chrysler Lebaron 2.2L TBI 4cyl the Fuel Filter is located under vehicle, passenger side, below trunk area, next to fuel tank, mounted in fuel line.

Hope this helps; remember to rating this answer leaving a testimonial comments. Thank you for using Fixya.

Oct 17, 2011 | 1989 Chrysler LeBaron

1 Answer

Engine light on po455


CODE PO455 - EVAP SYSTEM LARGE LEAK DETECTED. POSSIBLE CAUSES. FUEL FILLER CAP LOOSE. PURGE SOLENOID VALVE IS DAMAGED OR HAS FAILED. CHARCOAL CANISTER IS LOADED WITH FUEL OR MOISTURE OR HAS FAILED. CANISTER DRAIN CUT VALVE CDCV IS DAMAGED OR LEAKING. FUEL TANK PRESSURE SENSOR IS DAMAGED OR HAS FAILED.CATCH TANK OR ROLLOVER VALVE IS DAMAGED OR FUEL TANK IS LEAKING. VAPOR LINES DAMAGED OR LEAKING BETWEEN THE PURGE SOLENOID AND INTAKE MANIFOLD PURGE SOLENOID AND CANISTER OR BETWEEN THE PRESSURE CONTROL VALVE.CHECK VALVE AND ROLLOVER VALVE. PCM HAS FAILED.

Aug 22, 2011 | 2001 Mazda MPV

1 Answer

How to locate the gas filter on a voyager 4cl lx 2003


FUEL FILTER LOCATED ON TOP OF FUEL TANK.YOU HAVE TO LOWER TANK JUST ENOUGH TO REMOVE FUEL FILTER.FIRST RELIEF FUEL PRESSURE BEFORE REMOVING FUEL FILTER.TO RELIEF FUEL PRESSURE REMOVE FUEL FILLER CAP.REMOVE FUEL PUMP RELAY FROM THE FUSE AND RELAY BOX LOCATED LEFT SIDE OF THE ENGINE COMPARTMENT. START ENGINE LET IT RUN UNTIL IT RUN OUT OF FUEL.CRANK ENGINE OVER FEW MORE TIMES TO MAKE SURE ALL FUEL OUT OF FUEL LINE.NOW FUEL PRESSURE IS RELIEF.WHEN YOU ARE DONE CHECK FOR FUEL LEAKS BEFORE DRIVING VECHICLE.

Dec 26, 2010 | 2003 Chrysler Voyager

1 Answer

How to rplace the fuel pump+


Check this procedure to REMOVAL & INSTALLATION
(see Figures 1, 2 and 3 / click over pics for zoom)

zjlimited_258.jpg

Fig. 1: Remove the nuts retaining the access cover in the trunk

zjlimited_259.jpg

Fig. 2: Once the cover is removed, access to the pump is obtained



zjlimited_260.jpg

Fig. 3: Note the alignment marks must be met to install the pump correctly
An electric fuel pump is used with fuel injection systems in order to provide higher and more uniform fuel pressures. It is located in the tank. To perform the testing or servicing, you will need a DRB III or equivalent scan tool.

  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Open the trunk lid, then remove the trunk liner.
  4. Remove the access panel fasteners.
  5. Remove the access panel and gasket. Inspect the gasket for damage. If necessary, replace the gasket.
  6. Disconnect the electrical wiring from the top of the pump module.
  7. Disconnect the fuel supply and return tubes from the fuel pump module.
  8. Disconnect the hose from the pressure relief/rollover valve.
  9. A band clamp fastens the pump module to the tank. The module rises up from the tank after loosening the clamp.
  10. Loosen the band clamp until the pump module rises up from the tank.
WARNING The pump reservoir may contain fuel. Do not spill fuel while removing the module.
  1. To absorb any possible spillage, place a shop towel around the access opening. Without removing the modular, tip it backwards to allow fuel in the reservoir to run down the side and back into the tank.
  2. The float arm of the sensor catches on the inside of the tank while removing the module. Tilt the module to the one side when removing it from the tank.
  3. Remove the pump module and gasket from the tank.
  4. Drain the remainder of fuel from the reservoir before servicing the pump module.
To install:


The fuel pump module and tank have alignment marks. The tank has two molded lines at the ten o'clock position. The fuel pump has a triangular alignment mark. Align the marks to correctly position the pump.
  1. With a new gasket, insert the pump straight into the tank to set the float on the bottom. Align the marks on the pump and tank.
  2. Seat the pump to tank by pushing the top downward. Make sure the gasket does not slip over the outside or inside edge of the tank lip. While holding the pump in the seated position, place the band clamp over the lip of the tank and edge of the pump. Tighten the band clamp to 31 inch lbs. (4 Nm). Do not over tighten.
  3. Install the fuel tubes over the return and supply nipples on the module.
  4. Connect the vent line to the pressure relief/rollover valve.
  5. Attach the electrical wiring to the pump.
  6. Using a DRB III or equivalent scan tool, pressurize the fuel system.
  7. Check for leaks.
  8. Install the access cover and gasket. Tighten the fasteners.
  9. Install the trunk liner.
  10. Connect the negative battery cable.

Hope this hellps (remeber to rate this answer).

Dec 17, 2010 | 1997 Dodge Intrepid

3 Answers

Is the fuel pump located outside the gas tank or inside the gas tank?


HI. This vehicle has a fuel pump access cover located inside the trunk, under the carpet overlay. Once you have removed the carpet; the cover can be seen in the center section of the trunk bed. There are 4 retaining nuts that are holding the cover on the access hole. Remove the nuts retaining the access cover in the trunk and lift up the cover. Once the cover is removed, the fuel pump will be exposed for maintenance or replacement.
fc673e0.jpg

The complete fuel pump module assembly in located inside your tank under the cover.
7041258.jpg

Aug 09, 2010 | 1994 Chrysler Concorde

1 Answer

1995 Lebaron gtc fuel system shrader valve location?


if you cant find it on the rail there probably isn't one to find, you trying to do a pressure check???

May 25, 2010 | 1995 Chrysler LeBaron

1 Answer

Change fuel pump


Chrysler Concorde/Intrepid/LHS/New Yorker/Vision 1993-1997

Electric Fuel Pump - REMOVAL & INSTALLATION
(see Figures 1, 2 and 3)

bd45105.jpg

Fig. 1: Remove the nuts retaining the access cover in the trunk

3fb5c2c.jpg

Fig. 2: Once the cover is removed, access to the pump is obtained

9028002.jpg

Fig. 3: Note the alignment marks must be met to install the pump correctly

An electric fuel pump is used with fuel injection systems in order to provide higher and more uniform fuel pressures. It is located in the tank. To perform the testing or servicing, you will need a DRB III or equivalent scan tool.
  1. Release the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Open the trunk lid, then remove the trunk liner.
  4. Remove the access panel fasteners.
  5. Remove the access panel and gasket. Inspect the gasket for damage. If necessary, replace the gasket.
  6. Disconnect the electrical wiring from the top of the pump module.
  7. Disconnect the fuel supply and return tubes from the fuel pump module.
  8. Disconnect the hose from the pressure relief/rollover valve.
  9. A band clamp fastens the pump module to the tank. The module rises up from the tank after loosening the clamp.
  10. Loosen the band clamp until the pump module rises up from the tank.

WARNING The pump reservoir may contain fuel. Do not spill fuel while removing the module.
  1. To absorb any possible spillage, place a shop towel around the access opening. Without removing the modular, tip it backwards to allow fuel in the reservoir to run down the side and back into the tank.
  2. The float arm of the sensor catches on the inside of the tank while removing the module. Tilt the module to the one side when removing it from the tank.
  3. Remove the pump module and gasket from the tank.
  4. Drain the remainder of fuel from the reservoir before servicing the pump module.

To install:
The fuel pump module and tank have alignment marks. The tank has two molded lines at the ten o'clock position. The fuel pump has a triangular alignment mark. Align the marks to correctly position the pump.
  1. With a new gasket, insert the pump straight into the tank to set the float on the bottom. Align the marks on the pump and tank.
  2. Seat the pump to tank by pushing the top downward. Make sure the gasket does not slip over the outside or inside edge of the tank lip. While holding the pump in the seated position, place the band clamp over the lip of the tank and edge of the pump. Tighten the band clamp to 31 inch lbs. (4 Nm). Do not over tighten.
  3. Install the fuel tubes over the return and supply nipples on the module.
  4. Connect the vent line to the pressure relief/rollover valve.
  5. Attach the electrical wiring to the pump.
  6. Using a DRB III or equivalent scan tool, pressurize the fuel system.
  7. Check for leaks.
  8. Install the access cover and gasket. Tighten the fasteners.
  9. Install the trunk liner.
  10. Connect the negative battery cable.

Hope this help to solve your problem (remember rated and comment this).

Mar 23, 2010 | 1996 Dodge Intrepid

2 Answers

Where is the fuel pump located in a 1994 chrysler Lebaron gtc


Both 4 and 6 cylinder's fuel pump located in gas tank.

Jan 13, 2010 | 1994 Chrysler LeBaron

2 Answers

1987 chrysler lebaron 2.5, car runs fine, then cuts out, after awhile it runs again. in-tank fuel pump whirrs when ignition is turned on but only for a second, the car seems to have elec. when it kicks out...


i have had simmilar problems with my dodge dynasty and in the end an ignition coil fixed the problem.the fuel does only run for a second the will not run again until it see engine speed

Aug 07, 2009 | 1989 Chrysler LeBaron

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...