Question about 2001 Daewoo Lanos

Open Question

Brake line diagram ,2000 daewoo lanos - 2001 Daewoo Lanos

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

leirob007
  • 5 Answers

SOURCE: front brakes stick on

either your calipers are sticking and need replacing. OR the hoses have failed internally. and need replacing.. very rare but possible the master cylinder is not allowing the fluid to return usually caused bu a booster failing and causing some down travel in the master cylinder. I'd start by raising the front end up. appling hard brake pressure. turn the tire.. then loosen the brake bleeder to check for pressure. if the bleeder sprays fluid and the brakes release forget the calipers. if they are still tight then replace the calipers. pump them up again if they released.. and break the line free at the master cylinder. if they don't release then replace the hoses..

Posted on Nov 16, 2008

johnny5846
  • 379 Answers

SOURCE: 2000 daewoo lanos head torque

the 2000 daewoo lanos 1.6L dohc head torque is as follows , step 1 = 18 ft. lbs. , step 2 = 70 degrees , step 3 = 70 degrees , step 4 = 30 degrees . sequence is as pictured .

58bb502.jpg

there ya go , gears to the left , looking at the front of engine .

Posted on Jan 09, 2009

emissionwiz
  • 75744 Answers

SOURCE: Where is the timing mark for the camshaft on a 2000 Daewoo Lanos?

Here is the entire timing belt replacement procedure.
Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on May 22, 2009

stevenhurc
  • 450 Answers

SOURCE: Where is the timing mark for the camshaft on a 2000 Daewoo Lanos?

single cam or twin?

466b3f3.jpg 1f27bcc.jpg

Posted on May 28, 2009

  • 7 Answers

SOURCE: How to replace front wheel bearings on 2000 Daewoo Lanos

they come as a whole assembly hub and all

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lanos 2001 brake lines specifications


Measure the old ones or cut to length while fitting new ones using the proper flaring tool or compression fittings.

May 18, 2015 | 2001 Daewoo Lanos

1 Answer

Best way to remove a spoiler off a Daewoo lanos 2000 model,


Its bolted up from under the boot lid just like the astra ,simple once you have the panel off the inside of the boot .If it has a brake light inside the spoiler then you cannot remove it as this will infringe the certificate of homoglonation and the vehicle will fail its yearly mechancial inspection .

Feb 11, 2012 | 2000 Daewoo Lanos

1 Answer

I have a 2000 Daewoo Lanos hatchback. All the turn signals quit working last weekend but all other lights work. I suspect I have a bad fuse. What fuse do I need to replace and where is it located?


since the tail lamps and brake lamps work it will not be a fuse
the directional switch incorporated inside the steering column needs to be checked

Aug 20, 2011 | 2000 Daewoo Lanos

1 Answer

I need to put on the timing belt were do i set the crank and over head cams


Hi, I'm having trouble linking to you on the chat window, but here is a link to the diagrams you would need. Please let me know if you have any questions. http://www.2carpros.com/diagrams/daewoo/lanos/2000

Apr 05, 2011 | 2000 Daewoo Lanos

1 Answer

2000 Daewoo. Lanos won't start. What are the cam shaft positions


both lobes on number 4 cylinder face each other (point towards centre of engine)when timming marks on cam gears are lined up

72ae3c2.jpg

Aug 24, 2009 | 2000 Daewoo Lanos

1 Answer

Binding brake


hand brake cable adjuster lives under centre console at rear 10mm spanner required unadjust this and then remove rear drums to adjust linings so they just drag on drum then go back and adjust cable in car

Jun 03, 2009 | 1999 Daewoo Lanos

1 Answer

Timing belt diagram for 2000 Deawoo


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
http://www.2carpros.com/car_repair_information/year/2000/make/daewoo/model/lanos/2000_daewoo_lanos_timing_belt_diagram_marks.htm

Apr 04, 2009 | 2000 Daewoo Lanos

1 Answer

Radio code daewoo lanos 2000


Try one of these, I found these codes online mine was one of them for my Daewoo Lanos 2000.
1165 5241 1341 6361 4353 1156 4362 4316 3241 2145 5632 1636 5813 1651 1652 5436 3451 5324 4513 5346 4524 1857 1638 2152 5624 3346 1656

Feb 05, 2009 | 2000 Daewoo Lanos

2 Answers

2000 daewoo lanos head torque


the 2000 daewoo lanos 1.6L dohc head torque is as follows , step 1 = 18 ft. lbs. , step 2 = 70 degrees , step 3 = 70 degrees , step 4 = 30 degrees . sequence is as pictured .

58bb502.jpg

there ya go , gears to the left , looking at the front of engine .

Jan 09, 2009 | 2000 Daewoo Lanos

Not finding what you are looking for?
2001 Daewoo Lanos Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...