Question about Ford Escape

Open Question

Is bank one on a 2004 ford escape v6 engine located towards the front of the vehicle or the rear

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

  • 225 Answers

SOURCE: Need locations of o2 sensors in a 04 Ford Escape.

bank 1 sensor 1 is next to the fire wall. on the upper end of the exhaust

Posted on Aug 14, 2009

Testimonial: "Thank you for your help!!"

bschilz
  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks

7acfed1.gif
d9eb1af.gif

Posted on Oct 20, 2009

  • 31 Answers

SOURCE: when i turn the air on it doesn't flow from the front vents.

Sounds like the switch or actuator is not operating. Some vehicles have mechanical operators, and some have vacuum actuators. If a vacuum line is loose, it will not actuate.

Posted on Aug 01, 2010

ZJLimited
  • 17970 Answers

SOURCE: Engine misfire 2004 ford escape v6 3.0 ltr, need

2004 Ford Escape 3.0 liter V-6 VIN "1"

2b4e09d.gif


The next, I "bid" it. Good luck.

Posted on Oct 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Bank1 sendor 1 02 sensor-where is it?


bank 1 means before convertor on manifold usually ! has to be cold when doing it and very careful not to break it when removing or installing. its done with a socket but some have special plugs so be carefull don't drop sensor. some have 2 or 3. o2 sensors. before replacing look for loose vaccum lines and if you don't find any then replace it. some times you can get a false reading and the fix will be something different.

May 22, 2014 | 2004 Dodge Ram 1500

1 Answer

Where is number 5 cylinder located


On Ford engines, #5 cylinder is located between #4 cylinder and #6 cylinder (see picture) Please note that the arrow in the picture is pointing toward the fornt of the engine, NOT the front of the vehicle. With this in mind, the picture is accurate for both front wheel drive vehicles and rear wheel drive vehicles.

7_23_2011_11_58_41_pm.gif

Jul 23, 2011 | 2004 Ford Freestar

1 Answer

I'm getting codes with obd II read for o2 sensor 1 bank 1 and sensor 1 bank 2 i have a rough running 2004 ford escape 3.0 V6


If the O2 Sensors are original,you could just change the front 2

The ones closest to the engine.

Any other issue you need to actually diagnose, as codes
are for just that reason

They don't ever tell you to replace anything

Running rough is more the O2 Sensors

Plugs
MAF Dirty
Vacuum Leaks
Ignition Coils going bad

May 31, 2011 | Ford Escape Cars & Trucks

2 Answers

2004 saturn vue v6 sensor 1 bank 1 where is that


zjlimited_569.jpg

Fig. Heated Oxygen (HO2S) location (bank 1, sensors 1 & 2) - 3.5L engine


zjlimited_570.jpg

Fig. Heated Oxygen (HO2S) location (bank 2, sensors 1 & 2) - 3.5L engine


Hope helps.

Jan 28, 2011 | Saturn Vue Cars & Trucks

1 Answer

This question is for a 2001 ford escape 3.0L v6 i need the number order for the ignition coils 1 to 6


Hello! The firing order is; 1-4-2-5-3-6...Left bank, from front to rear=1-2-3...Right bank,from front to rear=5-6-4....

Guru...................Saailer

Aug 10, 2010 | 2001 Ford Escape

2 Answers

Whats firing order diagram of 2002 ford escape v6 engine


Ford V6's - rear bank of cylinders are 1 - 2 - 3. Front bank are 4 - 5 - 6 starting from passenger side (front) of engine.
Your firing order is
1 - 4 - 2 - 5 - 3 - 6

You're welcome.

Sep 29, 2009 | 2002 Ford Escape

2 Answers

Repalced O2 sensors, mass air flow sensor, and plugs error messag


Did you reset the system also sounds like you might be having ECM problems. I would try disconnecting the negative battery cable for a few minutes and reset the system and see if that helps. If that doesnt work I would have the computer checked out.

Aug 15, 2009 | 2004 Ford Escape

2 Answers

Ford escape 2002 firing order


V6 1-4-2-5-3-6 back bank pasenger side right to left cylinders 1 2 3
front bank passenger side right to left 4-5-6
4 cly 1-3-4-2

Jun 23, 2009 | 2002 Ford Escape

1 Answer

Firing order


for the 1993 probe i could only find a 2.5 V6. there are two banks of cylinders, odd and even. in other words as you stand in front of the vehicle the odd bank is toward the firewall, the even bank is closest to you.
the number one cylinder is on the passenger side toward the firewall and firing order is 1-2-3-4-5-6. hope that helps

Jun 02, 2009 | 1993 Ford Probe

1 Answer

O2 sensor


On the left front part of the engine, near the bottom, you also have a second one underneather the car right past the engine towards the rear of the car

Feb 08, 2009 | 2001 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...